Hisense MWH411B TV WiFi Module User Manual

Hisense MWH411B TV WiFi Module

Product Description

The TV’s WIFI module allows users to connect their TV to a WIFI network. This module can be operated in all European countries, USA, and Canada.

Basic Parameters

IEEE802.11b: DSSS (Direct
Sequence Spread Spectrum), OFDM (Orthogonal Frequency Division
Multiplexing) for IEEE802.11a/g/n
Data Transfer Rate| —-
Antenna Reference| 2T2R
Interface| —-
Supply Voltage| —-
Dimension| —-
Operating Temperature| —-
Storage Temperature| —-

RF Output Power

The limited power of the WLAN is 2412MHz-2472MHz.

| Banda| Limited power
---|---|---
WlAN| 2412MHZ-2472MHZ| < 20
5150MHZ-5850MHZ

Product Usage Instructions

To connect your TV to the WIFI network using the TV’s WIFI module follow these steps:

1. Insert the TV’s WIFI module into the designated slot on your TV.
2. Turn on your TV and go to the settings menu.
3. Select the network settings option.
4. Select the WIFI option and it will start scanning for available networks.
5. Select your WIFI network from the list of available networks.
6. Enter your WIFI password and select Connect.
7. Your TV is now connected to the WIFI network using the TV’s WIFI module.

The display method of Model approved code
In the factory, the model approve code is pasted on the back shell in a label.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures：

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of FCC RF Rules. This equipment should be installed and operated with a minimum distance of 20 in (50cm) between the radiator and your body. This transmitter must not be co- located or operated in conjunction with any other antenna or transmitter

CAUTION:
To comply with the limits of the Class B digital device pursuant to Part 15 of the FCC Rules, this device is compliant with Class B limits. All peripherals must be shielded and grounded. Operation with non-certified peripherals or non-shielded cables may result in interference to radio or reception

MODIFICATIO N
To assure continued compliance, Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the device.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 50 cm(8 in )between the radiator and your body NOTE To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product Contains Transmitter module FCC ID: SARMWH411B To satisfy IESD exterior labeling requirements, the following text must be placed on the exterior of the end product ” Contains Transmitter module IC ID: 27123-MWH411B

This symbol on the product or on its packaging indicates that this product must not be disposed of with your household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Manufacturer: Qingdao Hisense Communication Co., Ltd.
Address: 218 Qianwangang Road, Qingdao Economic & Technological Development Zone, Qingdao, China
Importers:

Hisense France SAS
Address: 9 Rue des 3 Soeurs, 93420 Villepinte, France
Hisense Iberia, S.L.U
Address : Ronda Auguste y Louis Lumiere. 23 Nave 12. Edificio Lumiere – Parque Tecnológico 46980

Paterna (Valencia) – Spain
Hisense Italia S.r.l
Address: Via Montefeltro, 6/A, 20156 MILANO
Hisense South Africa
Address: The Estuaries, Building 17 Oxbow Crescent, Century City, Cape Town, South Africa.

1. the device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; Footnote4
2. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
3. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate; and
4. where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.

This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:
“Operation is subject to the following two conditions:

1. this device may not cause interference and
2. this device must accept any interference, including interference that may cause undesired operation of the device.”

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>