DAIKIN IBPRO6 Monochrome Airzone Think Radio User Manual

DAIKIN IBPRO6 Monochrome Airzone Think RadioWARNINGS AND ENVIRONMENTAL POLICY

For your security, and to protect the devices, follow these instructions: Do not manipulate the system with wet or damp hands.
Disconnect the power supply before making any connections.
Take care not to cause a short circuit in any of the system connections.

ENVIRONMENTAL POLICY

Do not dispose of this equipment in the household waste. Electrical and electronic equipment contain substances that may damage the environment if they are not handled appropriately. The symbol of a crossed-out waste bin indicates that electrical equipment should be collected separately from other urban waste. For correct environmental management, it must be taken to the collection centres provided for this purpose, at the end of its useful life. The equipment components may be recycled. Act in accordance with current regulations on environmental protection. If you replace it with other equipment, you must return it to the distributor or take it to a specialized collection centre.
Those breaking the law or by-laws will be subject to such fines and measures as are laid down in environmental protection legislation.

AIRZONE BLUEFACE

Interface with a 3,5” colour screen for controlling the air conditioning.

• Basic functions of air conditioning control.
• Room temperature and relative humidity reading.
• Eco-Adapt saving function.
• Navigation through zones.
• Time schedules.
• Wired communication.

AIRZONE THINK

Low-energy E-ink thermostat for controlling your air conditioning through capacitive buttons.

• Basic functions of air conditioning control.
• Room temperature and relative humidity reading.
• Navigation through zones.
• Wired/Wireless communication1

AIRZONE LITE

Interface for controlling the air conditioning through capacitive buttons.

• On/off button.
• Buttons for selecting the temperature.
• Wired/Wireless communication.

AIRZONE BLUEFACE

SCREENSAVER

The screensaver pops up after about 15 seconds of inactivity, displaying the following information:

• Time and date. This information can be edited from the user settings menu. (See section user settings).
• Current zone. It indicates the zone where the interface is located.
• Room temperature. It indicates the room temperature of the zone where the Blueface is located.
• Relative humidity. It indicates the humidity of the zone.
• Zone state. It displays information about the zone state and settings, warnings and errors of the system (see section system warnings and errors).
• On/Off. On and off of the zone where the thermostat is located.

HOME SCREEN

• Operation modes. Select among the available modes: cooling, heating, ventilation and stop. (See section air conditioning control and operation modes).
• Eco-Adapt function. It offers several energy efficiency levels and also adapts the temperatures to boost the efficiency of your system. (See section air conditioning control; Eco-Adapt saving function).
• Fan Speed. It sets the operating speed of the AC unit fan. (See section Fan Speed).
• Current zone/Room temperature. It indicates the zone where the thermostat is located. The name of the zone can be edited. It also works as shortcut to zone navigation. (See section navigation through zones). It displays the current temperature of the zone where the Blueface is located.
• User settings. From this parameter you can control several functions such as the language, the screen brightness, the screensaver, etc. (See section user settings)
• Set-point temperature. Press on the temperature to set the set point. (See section air conditioning control)
• Relative humidity. It indicates the humidity of the zone.
• Air conditioning control. Control menu of the basic functions of Airzone systems.
• Time schedules. In this menu, you can program your Airzone system and activate/deactivate time schedules. (See section time schedules).
• System consumption. It provides information about the consumption of your system.
• Zone settings. Sleep, anti-freezing and other parameters depending on your type of system (See section zone settings).
• On/Off. On and off of the zone where the thermostat is located.

HOW TO USE THE BLUEFACE

Air conditioning control

• On/Off: Press this icon to switch on or off the zone where the thermostat is located.
• Temperature control:  Press on the temperature and use the – and + icons to select the desired set-point temperature (accuracy: ±0.5°C). The available ranges for heating mode are: 15-30° C. For cooling mode, they are: 18-30° C. These ranges may vary depending on the level of efficiency (Eco-Adapt) set on the master thermostat.
• Operation modes: It displays the operation mode of the system. This parameter can be accessed from your master thermostat. The available modes are:
• Stop. The air conditioning system will be off regardless of state of demand of the rest of the zones. In addition, all the terminal elements (ventilation grills, gates…) will remain closed.
• Cooling. In this operation mode, the system works exclusively in cooling mode when any of the zones is generating demand (Setpoint T < room Ta
• Heating. In this operation mode, the system works exclusively in heating mode when any of the zones is generating demand (Setpoint T <room T).
• Ventilation. In this operation mode, the system works exclusively in ventilation mode when any of the zones is generating demand (Setpoint T < room T).
• Dry. In this operation mode the system works in dry mode, refreshing the zone (reducing the humidity) when any of the zones is generating demand (Set-point T< Rooam T).
  Note: This mode is ideal for high humidity days: it reduces the appearance of water particles in the grilles.

Eco-Adapt function: It offers several energy efficiency levels and also adapts the temperatures to make your system more efficient. Eco-Adapts sets limits based on the level of efficiency:
Disabled. In this option, there are no saving limits. The available temperature ranges of temperatures are the ones allowed by the system: 15-30 °C in heating mode and 18-30 °C in cooling mode.
Manual. It sets the temperature limits of the zones according to the temperature set in the Master thermostat.
Efficiency indicator. Depending on the operating temperature, the Blueface displays a range of colors that reflects the level of efficiency of the system:

Green: very efficient
Yellow: efficient
Orange : inefficient
Red: very inefficient

Fan Speed: It is used to set the speed of the AC unit fan. The speed is set in automatic mode by default, imposing the flow depending on the number of zones in demand. In fancoil installations, the system speed can be manually selected from the Master thermostat.

High speed.
Low speed.
Medium speed.
Automatic speed.
Depending of the installation, enables to directly select the speed of the unit, setting the value 1 as the lowest speed. The speed is set in automatic mode by default.

Navigation through zones

From the main screen press on the name of the zone, a list with all the zones and their status will be displayed. This screen enables the control of all the zones at the same time or individually, it is also possible to switch on/off the zones from this screen, press < and > to see the rest of the zones.

The “All zones” option gives access to the control of all the zones at the same time, broadcasting the changes to all of them. Press on the zone’s name to access to all the parameters of the zone and control them from your controller. When the system detects a temperature error on a specific zone, the zone displays the error code instead of the room temperature (see section Warnings and errors).
Remote zone icons:

• Exit zone. It closes the zone and returns to the main zone.
• It returns to the list of zones.

ADVANCED USE OF AIRZONE BLUEFACE THERMOSTAT

User settings

Use this parameter to control and change all the basic functionalities. Touch once to display the shortcuts. Press on the icons to access the parameters.

Language/Country. Select the values for your system.
Brightness. You can set the brightness intensity and determine whether want to activate the screen brightness while the screensaver is displayed or not.
Date and time. Press on the clock to set the time, the format type (12 or 24 hours) and if you want the system to change the time automatically. Press on the calendar to set the date.
Clean screen. Select this option if you want to clean the screen. The screen will lock for a few seconds in order to help you clean it.
Screensaver. You can define the information displayed on the screensaver. Depending on your system configuration, you can select

• State of the zone: it displays information about the state and configuration of the zone.
• Weather information: Only available with Webserver Airzone Cloud.
• AC unit consumption: only available for computers with consumption reading.
• If you disable the information option, only the time and state will be displayed. Information. This parameter provides information on:
• Zone: firmware, zone, association, actuator or status of the communications.
• System: firmware, settings and information about the system controllers.
• Devices: It displays the elements connected to the system.
• Webserver: How to configuration and how to associate it, IP address and MAC address.
• Errors: Warnings on system incidents.

Times schedules

If you press the time schedule icon, you will access the menu where you can schedule up to 24 per zone:

Use the Add icon to apply a time schedule to a zone and follow the instructions.

• 1. Select the type of time schedule you want to apply and press confirm. There are two types of schedules:
  •  Mode. Allows to choose the operation mode (only available for Master Blueface).
  • Temperature. Allows to choose the temperature of the zone for cooling and heating mode.
• Select the days of the week, the time and the type of time schedule to be applied on the schedule
•  Press Confirm.

To activate/deactivate or modify a schedule, press the desired schedule to access the edit setting and then press the On/Off selector or parameters to modify.
Press and hold on any schedule to see all the available settings:
Edit: Changes the name of a schedule. To edit the name of a schedule, press and hold the name of the zone to access the name editor. Then, change the name.
Delete. It deletes a schedule.
Copy. You can copy a schedule to apply it in any other zone.
When you activate a schedule, the schedule icon is displayed as usual . If you deactivate it, the icon will be displayed as crossed out. Also, the list of schedules will be deactivated although visible .
If you have Airzone Cloud with calendar schedules created, remember that in the event of conflict these schedules have priority over those created for each zone. The priority set for time schedules is:Calendar schedules > system schedules > zone schedules

System consumption

This menu displays daily information about the consumption of your system (Airzone consumption meter required):

• Zone and system usage time.
• Power consumption (power currently used by the AC unit and the accumulated consumption during the day).

System consumption

This menu displays information about the amount of time of air demand of the zone and also about the operation of the AC unit of the system during the day.
If your system provides information on the electrical consumption, it will display the current power of the unit and the accumulated consumption during the day.

Zone settings

From this menu you can act on:
Sleep Mode. The Sleep mode works as an auto power-off Eco-timer of the zone. These are the values you can select:
Off. The timing is off.
30. It activates the timing and switches off the zone after 30 minutes.
60. It activates the timing. After 30 minutes, the zone varies one degree its temperature. After 60 minutes, the zone will switch off.
90. It activates the timing. After 30 minutes, the zone varies one degree its temperature. After 60 minutes, the zone varies another degree the temperature. Finally, after 90 minutes, the zone will switch off.
Anti-freezing. It prevents the room temperature from dropping below 12°C, although the zone is off. (It will not activate in Stop mode).
Depending on the type of installation and on how your system is configured, there are some extra functionalities:
Grille angles: Define the angle of the grilles of the zone for cooling and heating modes. It is defined at 90° by default.
Adjust slats. Define the inclination type of the horizontal and vertical slats on the systems where this function is available.
Control stages: You can choose among:

• Air: Only uses air stage.
• Radiant: Only uses radiant air.
• Combined: The system combines both stages to reach the perfect comfort quickly and efficiently.

Note: for safety reasons the zone turns off when changing any of these parameters.
Q- Adapt: Select the control algorithm that best fits your installation. These are the available options:

• Maximum: The system operates at maximum speed, irrespective of the number of zones.
• Power: The speed of the system is higher than in standard mode to increase the flow.
• Standard: Mode by default. The system automatically regulates the speed based on the number of zones.
• Silence: The speed of the system is lower than in standard mode to reduce the noise.
• Minimum: The system operates at minimum speed, irrespective of the number of zones.

Note: If having the 0-10 V Gateway; the algorithm will, in addition, consider the minimum and maximum voltage values established by the installer within the menu
Lite settings. You can use this parameter to define base set-point temperature for zones with Airzone Lite. Besides, you can also configure your wired Airzone Lite cable to act as wireless (the LED light will switch off after a few seconds).
Note: To access the Lite Settings parameter from any Airzone Blueface thermostat, it is necessary to access the zone through the Zone Navigation parameter.
WARNINGS AND ERRORS: Airzone Blueface thermostat displays all the system warnings in your screensaver. Besides, if there is any error, it will be displayed on the screensaver, on the main screen and on “Errors”, in user settingsAnti-freezing. It will be only displayed when it is activated. (See Section Zone Settings).
Window. It indicates the air conditioning of the zone has been deactivated due to open window. Only available if the window contact of the system is activated.
DHW: DHW is active. If your system has DHW management and it is activated, you will see a message on your Blueface and the zone will be deactivated.
Low battery Lite. Low battery warning. Informs about the involved zone when the icon is pressed.

Incidents

If any of these errors occur, please contact your installer.

Error of comunication

1. Blueface thermostat – Main control board
2. Lite thermostat – Main control board
3. Gateway – Airzone system
4. BACnet gateway – Control board
5. Open-circuit temperature probe
6. Gateway – Indoor AC Unit
7. Short-circuit temperature probe
8. Webserver – Airzone System
9. Radiant elements control board – Main control board
10. Expansion module – Main control board
11. Consumption meter – Main control board
12. Lutron gateway – Airzone System
13. Measuring error in consumption meter
    C-02 Production control board – Central
    C-09 Aerotermic gateway – Production control board

AIRZONE THINK

SCREENSAVER

When the screensaver is displayed, you will see the following information:

Date. Informative parameter defined by the master controller in user settings (See section user settings).
Zone state. It displays information about the general settings of the zone: the state (on/off) and the operation mode. In case of failure, it also displays all the errors (See section warnings and errors).
Control bar. It adjusts (by pressing or by sliding) all the parameters controlled by the Think.
Airzone. A button used to confirm and return to home.
On/Off. On/off of the zone where the thermostat is located.

HOME SCREEN

Press on the Airzone icon once to deactivate the screensaver and go to home. Once there, you will find the following functions:

Navigate through the Think Controller by pressing the side buttons on the control bars.
Operation modes. It displays the operation mode selected from the Master controller: cooling, heating, ventilation and stop (See section Operation mode).
Eco-Adapt function. It defines the level of energy efficiency set by the Blueface.
Fan speed. It is an indicator of the fan speed of the AC unit. That speed is set from settings menu (See section Fan speed).
Zone/Room temperature. It displays the zone where the thermostat is located. Its name is defined from the Airzone Blueface thermostat. It displays the room temperature of the zone.
Settings menu. The Sleep mode parameters can be always configured. If you have a Master Think, you can change the operation mode and the fan speed. (See section setting menu).
Set-point temperature. It displays the temperature set from the Think control bar (See section temperature settings). Relative humidity. Indicator of the humidity of the environment.
Sleep Mode. Indicator of the state of the Sleep mode (set from settings menu or from the Blueface).
Time schedules. It displays the state (on/off) of the time schedules of the zone. It is set from the Blueface.
Control bar. It adjusts (by pressing or by sliding) all the parameters controlled by the Think.
Airzone. A button used to confirm and return to home.
On/Off. On/off of the zone where the thermostat is located.’

BASIC USE AIRZONE THINK THERMOSTAT

Temperature Settings

On/Off. Pressing the icon, you will swtich on or off the zone where the thermostat is located.
Temperature control. Select the set-point temperature (0.5 °C) using the control bar. These are the available ranges

• Heating mode: 15-30° C
• Cooling mode: 18-30° C

These ranges may vary based on the efficiency level (Eco-Adapt) selected on the master interface.
Operation mode: It displays the operation mode of the system. For Master Think thermostats, access the settings menu to change the operation mode. The available modes are:
Stop. The air conditioning system will be off regardless of state of demand of the rest of the zones. In addition, all the terminal elements (ventilation grills, gates…) will remain closed.
Cooling. In this operation mode, the system works exclusively in cooling mode when any of the zones is generating demand (Setpoint T < room T).
Heating. In this operation mode, the system works exclusively in heating mode when any of the zones is generating demand (Setpoint T <room T).
Ventilation. In this operation mode, the system works exclusively in ventilation mode when any of the zones is generating demand (Setpoint T < room T).
Dry. In this operation mode the system works in dry mode, refreshing the zone (reducing the humidity) when any of the zones is generating demand (Set- point T< Room T).
Note: This mode is ideal for high humidity days: it reduces the appearance of water particles in the grilles.
Fan Speed: It displays the the speed of the AC unit fan. For Master Think thermostats, access the settings menu to change the fan speed. The speed is set in automatic mode by default, imposing the flow depending on the number of zones in demand.

• High speed.
• Low speed.
• Medium speed.
• Automatic speed.

Depending of the installation, enables to directly select the speed of the unit, setting the value 1 as the lowest speed. The speed is set in automatic mode by default.

ADVANCED USE OF AIRZONE THINK THERMOSTAT

Settings menu

This menu allows the access to the options below:
Mode. For Master Think thermostats, select the operation mode for the system. (See section Operation mode). Speed. For Master Think thermostats, select the AC unit’s fan speed. (See section Fan Speed).
Sleep mode. The Sleep mode is an auto power-off timer of the zone. These are the values you can select:

Off. The timing is off.
30. It activates the timing and switches off the zone after 30 minutes.
60. It activates the timing. After 30 minutes, the zone varies one degree its temperature. After 60 minutes, the zone will switch off.
90. It activates the timing. After 30 minutes, the zone varies one degree its temperature. After 60 minutes, the zone varies one more degree its temperature. Finally, after 90 minutes, it switches off the zone.
Zone navigation. Access any zone of the system to change the set-point temperature, switch it on or off or see all its information.
WARNINGS AND ERRORS: The Airzone Think thermostat screenserver displays system warnings.
Anti-freezing. It will be only displayed when it is activated. (See Section Zone Settings).
Window. It indicates the air conditioning of the zone has been deactivated due to open window. Only available if the window contact of the system is activated.
DHW: DHW is active. If your system has DHW management and it is activated, you will see a message on your Blueface and the zone will be deactivated.
Low battery Lite. Low battery warning.
Incidents: If any of these errors occurs, please contact with your installer.

Error of comunication

• Blueface thermostat – Main control board
• Gateway – Airzone system
• BACnet gateway – Control board
• Gateway – Indoor AC Unit
• Webserver – Airzone System
• Radiant elements control board – Main control board Expansion module – Main control board Consumption meter – Main control board
• Lutron gateway – Airzone System
• C-02 Production control board – Central
• C-09 Aerotermic gateway – Production control board
• Short-circuit temperature probe
• Measuring error in consumption meter

On/Off. On/off of the zone. In addition, it indicates the operation mode by using different colours. (See section On/off).
Temperature settings. You can increase or lower by 3°C the set-point temperatures set in Lite Settings parameter of the Blueface thermostat.
Note: To access the Lite Settings parameter from any Airzone Blueface thermostat, it is necessary to access the zone through the Zone Navigation parameter. (See section Zone settings)
Important: After 10 seconds of inactivity, the Wireless Lite Thermostat will turn off the LEDs to save battery. The first press on
displays de status of the zone (On/Off, Operation Mode and Set Point Temperature). This pulsation enables the modification of the desired parameters (On/Off or Temperature).

USING YOUR AIRZONE LITE

Basic Functions:
On/Off. By clicking on the icon will turn on or off the area in which the thermostat is located. This button also works as indicator of the operation mode. It follows a colour code system:
Purple: Stop mode.
Red: Heating mode.
Blue: Cooling mode.
Green: The set-point temperature has been reached.

If the button remains solid, the controller is ON. If the button is blinking, the controller is OFF. The button remains solid for 10 seconds to show the status, then turns off.

Temperature Control. Using the buttons, in probe settings, you can rise or lower (up to 3 °C, in intervals of 1 °C) the set-point temperature with regard to the one set in the Blueface. (See section zone settings).
The Leds indicate the set-point temperature. If it exceeds the permissible temperature limit, the icons to adjust the temperature will flash indicating the limit has been reached.  Temperature Control. Using the buttons, in probe settings, you can rise or lower (up to 3 °C, in intervals of 1 °C) the set- point temperature with regard to the one set in the Blueface. (See section zone settings). The Leds indicate the set-point temperature.
If it exceeds the permissible temperature limit, the icons to adjust the temperature will flash indicating the limit has been reached.
Errors: On/Off icon flashing red quickly. Loss of communication with the central.

ABOUT THE BATTERY

Blueface thermostats and Think thermostats will display on their screen a battery alert when the batteries of the radio interfaces are dying.
Lite thermostats also report when their batteries are dying but on the Blueface thermostat display.
In order to replace the battery, please remove the thermostat from its support and then replace it (CR2450).

Important: We recommend using of top-brand batteries. Using low-quality batteries may reduce the duration of use.
Note: In case it has been installed do not forget to remove the security system before taking away the thermostat from the wall.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>