SAMSUNG CBAR210P Module User Manual
- June 6, 2024
- Samsung
Table of Contents
CBAR210P Module
User Manual
Functional Description
CM01BHS11MDWCE is the module for BLE at embedded and Digital appliance applications. It is based on the PHY+ PHY6212 solution which comprises a single chip with integrated BLE 5.0.
Features
-
BLE – compliant
-
Supports Adaptive Frequency Hopping
-
On-chip support for serial peripheral interface (master and slave modes)
-
Compact dimension: BLE Module(PHY+): 24.5mm x 11mm / H : 3.0 mm
-
Host Interfaces: UART Interface
-
RoHS compliant
-
Supply voltage range
VCC 3.3V(2.97V ~ 3.63V) -
Power Consumption: 200mW
Electrical Characteristics
Absolute Maximum Ratings
| Symbol | Parameter | Min. | Max. | Unit |
|---|---|---|---|---|
| VDD | DC Supply Voltage | 2.97 | 3.63 | V |
Power Consumption
| Parameter | Conditions | Min. | Nom. | Max. | Unit |
|---|
Tx mode (Max current)
TX Power| 5V, 0dBm(+/-5dB) Tx Power| | | 40| mA
Recommended Operating Conditions
| Symbol | Parameter | Conditions | Min. | Nom. | Max. | Unit |
|---|---|---|---|---|---|---|
| VDD | BLE Module(PHY+) Voltage | – | 2.97 | 3.3 | 3.63 | V |
| Top | Operating temperature(Ambient) | – | -20 | – | 85 | °C |
Environmental Characteristics
| Symbol | Parameter | Conditions | Min. | Max. | Unit |
|---|---|---|---|---|---|
| ESD | Electro-static discharge voltage | IC Level | -2K | +2K | V |
| Module Level | -4K | +4K | V | ||
| Connector Level | -8K | +8K | V | ||
| Top | Operating temperature | – | -20 | +85 | °C |
| Tstg | Storage temperature | – | -30 | +85 | °C |
RF Specifications
All measurements are made under nominal supply voltage, room temperature, and conducted conditions at each antenna port except antenna.
| Parameter | Conditions | Min | Typ. | Max | Unit |
|---|---|---|---|---|---|
| Frequency Range | 2402+K*2MHz (K=0-39) | 2402 | – | 2480 | MHz |
Receiver
Sensitivity (PER)| PER 530.8%| –| –| -70 dBm
Transmitter
Output Power| | –| 0| 2.0| dBm
ICFT| | -150| –| 150| kHz
Frequency Drift| | -50| –| 50|
Drift rate| | –| –| 20| kHz/50us
Frequency Deviation| Avg
(payload sequence 11110000)| 225| –| 275| kHz
Max
(payload sequence 10101010)| 185| –| –| kHz
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Radiation Exposure Statement :
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Industry Canada Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Industry Canada Radiation Exposure Statement (D claration d’exposition aux radiations ):
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20 cm between the radiator & your body.
IMPORTANT NOTE:
This module is intended for OEM integrators. The OEM integrator is still
responsible for the FCC compliance requirement of the end product, which
integrates this module.
20cm minimum distance has to be able to be maintained between the antenna and
the users for the host this module is integrated into. Under such a
configuration, the FCC radiation exposure limits set forth for a
population/uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could
void the user’s authority to operate this equipment.
The OEM integrator is responsible for compliance with all the rules that apply
to the product in which this certified RF module is integrated.
This module must be integrated into a device where the user cannot access the
antenna connector and should not be able to remove or install the module.
USERS MANUAL OF THE END PRODUCT:
In the user’s manual of the end product, the end-user has to be informed to
keep at least 20cm separation with the antenna while this end product is
installed and operated. The end-user has to be informed that the FCC radio-
frequency exposure guidelines for an uncontrolled environment can be
satisfied. The end-user has to also be informed that any changes or
modifications not expressly approved by the manufacturer could void the user’s
authority to operate this equipment. If the size of the end product is smaller
than 8x10cm, then an additional FCC part 15.19 statement is required to be
available in the user’s manual: This device complies with Part 15 of FCC
rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following ”
Contains TX FCC ID: A3LCBAP210A “. If the size of the end product is larger
than 8x10cm, then the following FCC part 15.19 statement has to also be
available on the label: This device complies with Part 15 of FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
IC Statement
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du
Canada.
This device and its antenna(s) must not be co-located or operated in
conjunction with any other antenna or transmitter.
The device could automatically discontinue transmission in case of the absence
of information to transmit or operational failure. Note that this is not
intended to prohibit transmission of control or signaling information or the
use of repetitive codes where required by the technology.
IMPORTANT NOTE:
This module is intended for OEM integrators. The OEM integrator is still
responsible for the IC compliance requirement of the end product, which
integrates this module.
20cm minimum distance has to be able to be maintained between the antenna and
the users for the host this module is integrated into. Under such a
configuration, the IC RSS-102 radiation exposure limits set forth for a
population/uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could
void the user’s authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
In the user’s manual of the end product, the end-user has to be informed to
keep at least 20cm separation with the antenna while this end product is
installed and operated. The end-user has to be informed that the IC radio-
frequency exposure guidelines for an uncontrolled environment can be
satisfied. The end-user has to also be informed that any changes or
modifications not expressly approved by the manufacturer could void the user’s
authority to operate this equipment. IC statement is required to be available
in the user’s manual: This Class B digital apparatus complies with Canadian
ICES-003. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following ”
Contains TX IC: 649E-CBAR210P “.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>