CHARLXEE BTF-PINK Unicorn Bluetooth Headphones User Guide

Charlee UNICORN BLUETOOTH HEADPHONES

ATTENTION: PLEASE READ THIS MANUAL CAREFULLY BEFORE USING THE PRODUCT AND KEEP IT PROPERLY.
PACKING LIST:
– WIRELESS HEADSET
-INSTRUCTION SHEET
-USB CHARGING LINE
-1pcs 3.5MM Audio Cable
-25 pcs Unicorn Stickers
-1pcs Unicorn Bracelet

METHOD OF USE

POWER ON| PRESS THE MULTIFUNCTION BUTTON FOR ABOUT 3 SECONDS UNTIL THE LED LIGHT TURNS BLUE
---|---
POWER OFF| LONG PRESS THE MULTIFUNCTION BUTTON FOR ABOUT 3 SECONDS UNTIL THE LED IS OFF AND THEN RELEASE
STANDBY STATUS PROMPT| IN STANDBY STATE, BLUE FLICKER MEANS THE POWER IS SUFFICIENT, AND RED FLICKER MEANS THE POWER IS TOO LOW
CHARGING STATUS PROMPT| THE RED LIGHT IS ALWAYS ON WHEN CHARGING, AND THE BLUE LIGHT IS ALWAYS ON AFTER CHARGING
ANSWER/ HANG UP| PRESS THE MULTIFUNCTION BUTTON ONCE TO ANSWER AN
INCOMING CALL AND AGAIN TO HANG UP THE CALL
VOLUME| LONG PRESS “VOLUME +” OR “VOLUME -” TO ADJUST
STOP/ PLAY| PRESS THE MULTIFUNCTION BUTTON ONCE TO PAUSE THE MUSIC WHILE IT IS PLAYING, AND THEN AGAIN TO CONTINUE
LAST/ NEXT| QUICKLY PRESS THE VOLUME “+” OR VOLUME “-” BUTTON ONCE

PARAMETER

CONNECTION METHOD:

1. PRESS AND HOLD THE BUTTON ON THE HEADPHONE TO TURN ON THE HEADPHONE AND YOU WILL SEE THE LIGHT FLASH RED AND BLUE. THIS INDICATES THAT YOUR HEADPHONE IS READY TO PAIR.
2. FROM YOUR SMARTPHONE OR TABLET, FIND A LIST OF NEARBY DEVICES & CHOOSE “Charlxee-Unicorn ”. THE HEADPHONE WILL FLASH A BLUE LIGHT WHEN THE PAIRING IS COMPLETE.

CONNECTION LOST?
-IF PAIRING THE HEADPHONE DOES NOT WORK, TURN OFF THE HEADPHONE AND REPEAT THE STEPS AGAIN IN “PAIRING YOUR  HEADPHONE”.
-MAKE SURE YOUR HEADPHONE IS WITHIN RANGE OF YOUR SMART DEVICE.
-IF YOU HEAR A LONG BEEP, YOU NEED TO RECHARGE YOUR HEADPHONE. CONNECTION MAY LOST DUE TO LOW BATTERY.
-WHEN CHARGING YOUR HEADPHONE, ONLY USE THE ENCLOSED USB CABLE
WARNING
-PLEASE STORE AND USE THE PRODUCT AT ROOM TEMPERATURE.
-DO NOT EXPOSE THE PRODUCT TO RAIN OR HUMIDITY.
-DO NOT THROW, TO AVOID PRODUCT DAMAGE DUE TO DROP.
-DO NOT DISASSEMBLE, REPAIR OR MODIFY THE PRODUCT BY YOURSELF.
-DO NOT WIPE THIS PRODUCT WITH CHEMICAL SOLVENT.
-DO NOT THROW AWAY OR SET FIRE TO AVOID DANGER.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements. in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>