JDS LABS EL DAC II + Digital-To- Analog Converter Instruction Manual
- June 6, 2024
- JDS LABS
Table of Contents
JDS LABS EL DAC II + Digital-To- Analog Converter Instruction Manual
SUPPORT
ONLINE
CONTACT@JDSLABS.COM
JDSLABS.COM/SUPPORT
BY PHONE
314 – 252 – 0936
9:30 AM – 6PM CST,
MONDAY THROUGH FRIDAY
BY MAIL
909 NBLUFFRD
COLLINS VILLE , IL 62234
UNITED STATES
QUICK SETUP
CONFIGURATION
Connectivity
EL DAC II+ accepts three methods of digital input:
Maximum RCA Output voltage is 2.0VRMS
- Many coax and optical sources are unable to reliably transmit at 192kHz.
** Windows 7 supports 24/192kHz maximum.
Listening Tips
For maximum signal fidelity, set the DAC to at least 24-bit audio and adjust digital volume slightly below 100% at your computer.
Only control volume from your amplifier.
Listen safely to conserve your hearing:
www.hearingloss.org
To ensure an optimal noise floor, always position audio equipment as far away as possible from wireless devices.
Operating Care
Use gentle force when touching the mode button, and when inserting or removing cables.
Set sampling rate to the highest integer multiple of your music collection. For example, use 176.4kHz for a collection of 44.1k or 88.2k or 176.4kHz files. Use 192kHz for a collection of 48k or 96k or 192k audio files. Alternatively, you may install the optional XMOS drivers in Windows for bitperfect ASIO playback.
EL DAC II+ automatically selects appropriate sampling rate in coaxial or optical modes.
SETUP
Computer Setup
EL DAC II+ requires no drivers in Windows 10/11, macOS, Linux, and modern
version of iOS
and Android. You may download drivers for Win7/8 from jdslabs.com/drivers.
These drivers
may optionally be installed in Win10/11 for ASIO support. Be sure to select
your new DAC
as the default playback device:
Windows 7/8/10/11
Right click the volume icon in your taskbar and choose Sound –> Playback.
Click the XMOS or JDS Labs audio device, then choose “Set Default”. For best
experience, also configure Properties:
- Enhancements: Check “Disable all enhancements”
- Advanced: See Listening Tips
macOS
Ensure JDS Labs audio device is selected from Audio Devices.
Troubleshooting
No USB device or “Failed to Play Audio”
Cause: USB Device is not initialized.
Solution: Turn DAC off, then back on to reset the USB device.
No sound in one channel
Cause: Bad cable, or incorrect computer settings.
Solution: Check balance settings; try another headphone or RCA cable.
Some macOS systems
will pan audio to the Left channel upon initial connection of a DAC. User must
restore balance
to center.
Audio is muted after resuming from sleep or hibernate in Win 10/11
Cause: Microsoft USB Audio 2.0 driver bug.
Solution: Install XMOS drivers, as per page 5.
POWER ADAPTERS
ATTENTION: Incorrect power adapters can result in capacitor explosion
hazards and device damage. Only use the power adapter included with your EL
DAC:
Application for Council Directives 2004/108/EC, 2006/95/EC, 2002/95/ EC. Conformity declared for EN55022:2011, EN611000-3-2, EN61000-3- 3, EN55024-2
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Read More About This Manual & Download PDF:
References
- JDS Labs - Makers of Element and Atom Headphone Amps + DACs
- Drivers & Firmware _ JDS Labs Customer Support
- Homepage - Hearing Loss Association of America
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>