Flymo 970483362 EasiGlide 300V Electric Hover Lawnmower User Manual

EasiGlide 300V Art. 970483362
EasiGlide 330V Art. 970483462
EasiGlide 360V Art. 970483562
Oper’s manual
Electric Hover Lawnmower

Original instructions.

This product may be used under supervision, or if instruction regarding the safe use of the product has been provided and the resulting dangers have been understood, by children aged 8 and above, as well as by persons with physical, sensory or mental disabilities or a lack of experience and knowledge. Children must not be allowed to play with the product. Cleaning and user maintenance must not be performed by children without supervision. The use of this product by young people under the age of 16 is not recommended.

Intended use:
The FLYMO Lawnmower is intended to mow the lawn in private domestic gardens and allotments.
The product is not intended for long-term use.

DANGER! Risk of injury!
Do not use the product to cut bushes, hedges, shrubs, to cut off climbers or grass on roofs or balcony boxes, to chop up branches, twigs, and to level irregularities in the soil. Do not use the product on a slope steeper than 20° maximum.

SAFETY

IMPORTANT!
Read the operator’s manual carefully before use and keep it for future reference.
Symbols on the product:

| Read operator’s manual.
---|---
Keep bystanders away.
Beware of sharp blades. Blades continue to rotate after the motor is switched off. Remove plug from mains before maintenance or if the cord is damaged.
Keep the mains cable away from the cutting blades.

General safety warnings
Electrical safety

DANGER! Electric shock!
Risk of injury due to electric shock.
The product must be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30 mm.
WARNING! Risk of physical injury!
Cut injury when the blade turns or the product starts accidentally.
Disconnect the product from the mains before you do maintenance or you replace parts. Thereby the disconnected socket must be in the visual range.

Cables
If extension cables are used, these must comply with the minimum cross- sections in the table below:

Minimum rating: 1.0 mm² size cable, 10 amps 250 volts AC.
Your product is supplied with cable wired directly into the product.

1. If the supply cord is damaged, it must be replaced by your local Husqvarna UK Ltd. Approved Service Centre or similarly qualified persons in order to avoid a hazard.
2. Do not wire an extension cable directly to your product yourself. Please contact your local Husqvarna UK Ltd. Approved Service Centre for further information on the connectors and kits available.
3. Only use extension cables specifically designed for outdoor use and which conform to one of the following specifications: Ordinary rubber (60245 IEC 53), Ordinary PVC  (60227 IEC 53), or Ordinary PCP (60245 IEC 57).

Training
a) Read the instructions carefully. Be familiar with the controls and the correct use of the machine.
b) Never allow children or people unfamiliar with these instructions to use the machine. Local regulations can restrict the age of the operator.
c) Never operate the machine while people, especially children, or pets are nearby.
d) Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property.

Preparation
a) While operating the machine always wear substantial footwear and long trousers. Do not operate the machine when barefoot or wearing open sandals. Avoid wearing clothing that is loose-fitting or that hanging cords or ties.
b) Thoroughly inspect the area where the machine is to be used and remove all objects which can be thrown by the machine.
c) Before using, always visually inspect to see that the blade, blade bolt, and the blade assembly are not worn or damaged. Replace worn or damaged components in set to preserve balance. Replace damaged or unreadable labels.
d) Before use check the supply and extension cord for signs of damage or aging. If the cord becomes damaged during use, disconnect the cord from the supply immediately. DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY. Do not use the machine if the cord is damaged or worn.

Operation
a) Operate the machine only in daylight or in good artificial light.
b) Avoid operating the machine in wet grass.
c) Always be sure of your footing on slopes.
d) Walk, never run. e) Mow across the face of slopes, never up and down.
f) Exercise extreme caution when changing direction on slopes.
g) Do not mow excessively steep slopes.
h) Use extreme caution when reversing or pulling the machine towards you.
i) Stop the blade(s) if the machine has to be tilted for transportation when crossing surfaces other than grass, and when transporting the machine to and from the area to be used.
j) Never operate the machine with defective guards or shields, or without safety devices, for example, deflectors and/or grass collector, in place.
k) Switch on the motor carefully according to instructions and with feet well away from the blade(s).
l) Do not tilt the machine when switching on the motor, except if the machine has to be tilted for starting. In this case, do not tilt it more than absolutely necessary and lift only the part, which is away from the operator.
m) Do not start the machine when standing in front of the discharge opening.
n) Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.
o) Do not transport the machine while the power source is running.
p1 ) Stop the machine, and remove the plug from the socket. Make sure that all moving parts have come to a complete stop.
– whenever you leave the machine,
– before clearing blockages or unclogging chute,
– before checking, cleaning, or working on the machine,
– after striking a foreign object. Inspect the machine for damage and make repairs before restarting and operating the machine;

if the machine starts to vibrate abnormally (check immediately)
– inspect for damage,
– replace or repair any damaged parts,
– check for and tighten any loose parts.

Maintenance and storage

a) Keep all nuts, bolts, and screws tight to be sure the machine is in safe working condition.
b) Check the grass collector frequently for wear or deterioration.
c) Replace worn or damaged parts for safety.
d) On machines with multi-blade, take care as rotating one blade can cause other blades to rotate.
e) Be careful during the adjustment of the machine to prevent entrapment of the fingers between moving blades and fixed parts of the machine.
f) Always allow the machine to cool down before storing.
g) When servicing the blades be aware that, even though the power source is switched off, the blades can still be moved.
h) Use only genuine replacement parts and accessories.

Additional safety warnings
Electrical safety

DANGER! Cardiac arrest!
This product makes an electromagnetic field while it operates. This field may under some conditions interfere with active or passive medical implants. To decrease the risk of conditions that can possibly injure or kill, we recommend persons with medical implants to speak with their physician and the medical implant manufacturer before they operate the product.
Before use, examine the cable for signs of damage or aging. If the cable is found to be defective, take the product to an authorized Service Centre and have the cable replaced.
Do not use the product if the electric cables are damaged or worn.
Immediately disconnect from the mains if the cable is cut, or the insulation is damaged. Do not touch the electric cable until the cable has been disconnected.
Do not repair a cut or damaged cable. Replace it with a new one.
The extension cable must be uncoiled. Coiled cables can overheat and reduce the efficiency of your mower.
Keep the extension cable away from the product, always work away from the power point mowing up and down, never in circles.
Do not pull cable around sharp objects.
Always switch off at the mains before disconnecting any plug, cable connector, or extension cable.
Stop the motor, disconnect the mains and examine the cable for damage or aging before you wind the cable for storage. Do not repair a damaged cable, replace it with a new one. Use only genuine replacement cable.
Always wind the cable carefully, avoid kinking.
Do not carry the product by cable.
Do not pull on the cable to disconnect any of the plugs.
Use only on AC mains supply voltage shown on the product rating label.
Our products are double insulated to EN60335. Do not connect the earth to any part of the product.
Check the working area for hidden cables.
Do not use for pond care or close to water.

Personal safety

DANGER! Risk of suffocation!
Small parts can be easily swallowed. There is also a risk that the polybag can suffocate toddlers. Keep toddlers away when you assemble the product.
Let the hover mower cool down for at least 30 minutes before storage or maintenance.
If blockage of cutting element stop product and check.
Do not tilt the machine in the direction of the user.
Do not move backward.
Stay alert during operation.
Do not use it in an explosive atmosphere.
Do not operate the product when you are tired, ill, or under the influence of alcohol, drugs, or medicine or when you are exhausted.
Do not overload the mower.
Use gloves, wear slip-resistant shoes, and wear eye protection.
Do not use it under wet conditions.
Do not use on wet grass.
Do not disassemble the product further than the delivery status.
Only start the mower with an upright standing handle.
Do not use the start levers alternately.
Use the handles carefully.

Safety Cut-Out
The motor is protected by a Safety Cut-Out which is activated when the blade becomes jammed or if the motor is overloaded. When this occurs, stop and disconnect the product from the mains. The Safety Cut-Out will only reset when you release the start/stop lever. Clear any obstruction and wait for a few minutes for the Safety Cut-Out to reset before you continue to use the product.

ASSEMBLY

DANGER! Risk of injury!
Cut injury when the product starts accidentally.
Wait for the blade to stop, disconnect the product from the mains and use gloves before you assemble the product.

To assemble the lower handle [ Fig. A1 ]:

1. Place the end of the lower handle (1) into the slots on the deck (2).
2. Secure the lower handles (1) to the deck (2) by firmly pushing fixing pin (3) through the holes in the deck (2) and handle (1).
3. Repeat on the other side.
   NOTE : Should a problem occur when securing the handle to the deck with the fixing pin, carefully lever fixing pinout of location and repeat steps 1 to 3 above.

To assemble the upper handle [ Fig. A2 / A3 ]:

1. Make sure that the upper handle (4) is located correctly with the safety lock-off button (5) on the switchbox facing upwards.
2. Make sure that the upper handle (4) and the lower handle (1) are aligned correctly.
3. Insert the nut into the handle knob (6) (if necessary).
4. Fit the bolts (8), the washers (7), the handle knob (6), and the mains cable hooks * (H) onto the handles (1) / (4) in the correct positions.

• The mains cable hooks (H) are selected models only. 5. Attach the cable (9) to the handles (1) / (4) with the clips (10) provided.
  Make sure that the cable (9) is not trapped between the upper handle (4) and the lower handle (1).

OPERATION

DANGER! Risk of injury!
Cut injury when the product starts accidentally.
→ Wait for the blade to stop, disconnect the product from the mains, and use gloves before you adjust or transport the product.

To connect the mower [ Fig. O1 / O2 ]:
DANGER! Electric shock!
To avoid damage to the extension cable (11), the extension cable (11) must be inserted into the cable lock (L).
→ Before you operate insert the extension cable (11) into the cable lock (L).

1. Connect the female extension cable (11) connector to the back of the switchbox (12).
2. Form a loop in the extension cable (11), insert the loop into the cable lock (L) slot in the switchbox (12), and pull tight.
3. Connect the extension cable (11) into a 230 V mains socket.

To adjust the cutting height [ Fig. O3 / O4 / O5 ]:
CAUTION! Do not use more than 3 cutting height spacers (13). The cutting height spacers (13) must only be fitted between the blade (14) and the fan (15). Do not fit the cutting height spacers (13) between the blade (14) and the blade bolt (16).

1. To remove the blade bolt (16), hold the fan (15) firmly and loosen the blade bolt (16) with the spanner (17) provided.

2. Remove the blade bolt (16), the blade (14), the cutting height spacers (13), and the fan (15).

3. Inspect for damage and clean as necessary.

4. Put the fan (15) on the product.
   Make sure that the fan (15) is fully in place and the hole of the fan is in line up with the threaded hole.

5. Put the cutting height spacers (13) onto the fan (15).
   Higher Cut – less cutting height spacers Lower Cut – more cutting height spacers Make sure that the pegs have located into the holes.

6. Put the blade (14) on by aligning the D-shaped holes onto the cutting height spacers (13).
   Make sure that the pegs have located into the holes on the blade.

7. Put the blade bolt (16) through the center hole of the blade (14).

8. Tighten down the blade bolt (16) clockwise by hand.

9. Hold the fan (15) firmly and tighten the blade bolt (16) with the spanner (17) provided.

Operation position:
Adjustment is not required to move the handle to the operating position.
Simply pull down from the forward position or lift up from the down position until the handle is in the most comfortable operating position.

To start the mower [ Fig. O6 / O7 ]:
DANGER! Risk of injury!
Risk of injury if the product does not stop when you release the start levers.
→ Do not bypass the safety devices or switches. For example, do not attach the start levers to the handle.

To start:
The product is provided with a two-handed safety device (start lever (18) and safety lock-off button (5)) to prevent the product from being turned on by accident.
There are two start levers (18) fitted. Either one has to be used to start.

1. Push the safety lock-off button (5) with one hand and pull the start lever (18) with the other hand.
   The mower starts.

2. Release the safety lock-off button (5).
   To prevent a ring from being cut in the lawn and to clear any residual grass, tilt the mower slightly. When the lawnmower has reached full speed gently lower it onto the lawn.

To stop:
→  Release the start lever (18).
The mower stops.

To empty the grass box [ Fig. O8 / O9 ]:
DANGER! Risk of physical injury!
Cut injury when the blade turns or the product starts accidentally.
→ Wait for the blade to stop, disconnect the product from the mains and use gloves before you put /remove the grass box.

Models with a transparent window (23) in the lid show the filling level of the grass box (22). This should be cleaned after every lawn mowing.

1. Push in the lid (21) where indicated and open the lid (21).
2. Remove the grass box (22) by the molded handle recesses at the front and rear of the grass box (22).
3. Empty the grass box (22).
4. Replace the grass box (22). Make sure that it locates securely onto the deck fixing locations.
5. Close the lid (21).
   Failure to fit the grass box (22) and the grass box lid (21) correctly can cause a poor collection of grass clippings.

Tips to use the mower [ Fig. O10 / O11 ]:
Mow twice a week during the growing season. The lawn will suffer if more than a third of its length is cut at one time and this may also result in the poor collection.
For the best results mow the outside edge of the lawn in a clockwise direction first.
Start to mow the edge of the lawn nearest to the PowerPoint. So the cable is laid out on the lawn you have already cut.
For best grass collection always mow in a straight line. Do not swing the lawnmower from side to side.
For the best cutting results mow in straight lines with an overlap of approximately 8 – 10 cm on each pass with the mower.
Do not overload the mower. To mow long thick grass may cause the motor speed to drop and you will hear a change in the motor sound. If the motor speed drops you may overload the mower which may cause damage. When you mow in long thick grass a first cut with the cutting height set higher will help reduce the load. See To adjust the cutting height.

**MAINTENANCE

**

DANGER! Risk of injury!
Cut injury when the product starts accidentally.
→ Wait for the blade to stop, disconnect the product from the mains and use gloves before you maintain the product.

To clean the mower:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
→ Do not clean the product with water or with a water jet (in particular high- pressure water jet).
→ Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.

The airflow slots must always be clean.

To clean the underside of the mower [ Fig. M1 ]:
The underside is easiest to clean after you mowed.

1. Lay the mower on its side carefully.
2. Clean the underside (19) by removing any grass build-up with the spanner/scraper tool (17).
3. Clean the blade (14) and the fan (15) with a soft brush (do not use sharp objects).

To clean the outside of the mower [ Fig. M2 ]:

1. Clean the outside with a dry cloth.
2. Clean the airflow slots (20) with a soft brush (do not use sharp objects).

STORAGE

To put into storage:
The product must be stored away from children.

1. Disconnect the product from the mains.
2. Clean the mower (see 4. MAINTENANCE).
3. Store the mower in a dry, enclosed, and frost-free place.

Storage positions [ Fig. S1 / S2 ]:

1. Push the lower handle (1) inwards from both sides simultaneously.

2. Rotate the handle (1) to the desired position, either forward for the folding storage position or backward for the wall mounting storage position.

3. Loosen the handle knob (6) and the mains cable hook (H) and fold the upper handle (4).
   Make sure that the cable is not locked between the lower and the upper handle.

4. Wrap the mains cable (11) securely around the mains cable hooks (H).

Folding storage position [ Fig. S3 ] Wall mounting storage position [ Fig. S4 ] NOTE: When wall-mounting storage, always hang the mower from the lower handle (1) cross-section.

Disposal:
(in accordance with RL2012/19/EC)
The product must not be disposed of to normal household waste. It must be disposed of in line with local environmental regulations.

IMPORTANT!
→ Dispose of the product through or via your municipal recycling collection center.

**TROUBLESHOOTING

**

DANGER! Risk of injury!
Cut injury when the product starts accidentally.
→  Wait for the blade to stop, disconnect the product from the mains, and use gloves before you troubleshoot the product.

To replace the blade:
DANGER! Risk of injury!
Cut injury when the blade turns and it is damaged, bent, out of balance, or has chipped edges.
→ Do not use the mower when the blade is damaged, bent, out of balance, or has chipped edges.
→  Do not regrind the blade.

The FLYMO spare parts are available from your FLYMO dealer or from the FLYMO service.
Only use an original FLYMO blade:
FLYMO Replacement Blade for 30 cm:
Reference no. FLY094
Part no. 529370590
FLYMO Replacement Blade for 33 cm:
Reference no. FLY095
Part no. 529370790
FLYMO Replacement Blade for 36 cm:
Reference no. FLY096
Part no. 529370890

→ Replace the blade (see 3. OPERATION To adjust the cutting height).

Connect the mains cable or if necessary replace it.
The motor is blocked.| Remove the obstacle.
The motor is jammed and makes a noise| The motor is blocked.| Remove the obstacle.
The cutting height is too low.| Raise the cutting height.
Loud noises, the mower is rattling| Screws on the motor, it’s fixing, or on the mower chasing are loose.| Let the screws be tightened by an authorized specialist dealer.
The mower runs unevenly or vibrates strongly| The blade is damaged/worn or the blade mounting is released.| Replace the blade.
The blade is very dirty.| Clean the mower (see 4. MAINTENANCE). If this does not rectify the problem, replace the blade.
Poor grass collection| The lid is not correct in place.| Put the lid correctly on the grass box.
Airflow slots are dirty.| Clean the mower (see 4. MAINTENANCE).
Not mowing in straight lines.| Mow in straight lines.
Lawn is not cleanly mowed| The blade is blunt or damaged.| Replace the blade.
The cutting height is too low.| Raise the cutting height.
Poor flotation| The underside of the mower is dirty.| Clean the underside of the mower.
The cutting height is too low.| Raise the cutting height.
The fan is damaged.|  Check and replace the fan.
If poor flotation persists, contact the local approved Service Centre.|

NOTE: For any other malfunctions please contact the FLYMO service department. Repairs must only be done by FLYMO service departments or specialist
dealers approved by FLYMO.

 TECHNICAL DATA

Electric Hover Lawnmower| Unit| Value (30 cm)| Value (33 cm)| Value (36 cm)
---|---|---|---|---
Rated power| W| 1700| 1700| 1800
Mains voltage| V| 230| 230| 230
Mains frequency| Hz| 50| 50| 50
Speed of rotation cutting| R/min| 4200| 4200| 4200
Cutting width| cm| 30| 30| 36
Cutting height adjustment| mm| 10 – 30| 10 – 30| 10 – 30
The volume of the grass box| l| 20| 20| 26
Weight| kg| 7.6| 7.6| 7.8
Sound pressure level LpA 1) Uncertainty kpA| dB (A)| 843| 833| 833
Sound power level LWA 2): measured/guaranteed Uncertainty kWA| dB (A)| 92 / 96
3.9| 92 / 96
3.2| 92 / 96
3.2
Hand/arm vibration avhw 1) Uncertainty know| m/s2| 1.5
1.5| 1.5
1.5| 1.9
1.5

Measuring process complying with: 1) EN 60335-2-77 2) RL 2000/14/EC

NOTE: The stated vibration emission value has been measured according to a standardized test procedure and can be used for the comparison of one electric power tool with another. It can also be used for preliminary evaluation of exposure. The vibration emission value can vary during the actual use of the electric power tool.

Please consult the supply authority, if necessary, that the equipment is connected only to a supply of an impedance no more than 0.354 Ω.
This maximum permissible system impedance at the interface point of the user’s supply is according to the test value of EasiGlide 360V.

ACCESSORIES

FLYMO Replacement Blade for 30 cm| As a replacement for the blunt blade.| Reference no. FLY094
Part no. 529370590
---|---|---
FLYMO Replacement Blade for 33 cm| As a replacement for the blunt blade.| Reference no. FLY095
Part no. 529370790
FLYMO Replacement Blade for 36 cm| As a replacement for the blunt blade.| Reference no. FLY096
Part no. 529370890

SERVICE / WARRANTY

Service:
Please contact the address on the back page.

Warranty Statement:
In the event of a warranty claim, no charge is levied to you for the services provided.
FLYMO grants a warranty for all original FLYMO new products for two years from the date of original purchase from the retailer, provided that the devices have been for private use only. This manufacturer’s warranty does not apply to products acquired second-hand. This warranty includes all significant defects of the product that can be proved to be material or manufacturing faults. This warranty is fulfilled by supplying a fully functional replacement product or by repairing the faulty product sent to us free of charge;  we reserve the right to choose between these options. This service is subject to the following provisions:

• The product has been used for its intended purpose as per the recommendations in the operating instructions.
• Neither the purchaser nor a third party has attempted to open or repair the product.
• Only Original FLYMO replacement parts and wear parts have been used for operation.
• Presentation of the receipt.

Normal wear and tear of parts and components (such as blades, blade fixing parts, turbines, light bulbs, V-belts / toothed belts, impellers, air filters, spark plugs), visual changes, wear parts, and consumables are excluded from the warranty.

This manufacturer’s warranty is limited to the replacement and repair of products in accordance with the abovementioned conditions. The manufacturer’s warranty does not constitute an entitlement to lodge other claims against us as a manufacturer, such as for damages. This manufacturer’s warranty does not, of course, affect statutory and contractual warranty claims against the dealer/retailer.
The manufacturer’s warranty is governed by the law of the Federal Republic of Germany.
In case of a warranty claim, please return the faulty product, together with a copy of the receipt and a description of the fault, with postage paid to the service address.

Consumables:
The blade is consumable and is not included in the warranty.

EN Product liability
In accordance with the German Product Liability Act, we hereby expressly declare that we accept no liability for damage incurred from our products where said products have not been properly repaired by an FLYMO-approved service partner or where original FLYMO parts or parts authorized by FLYMO were not used.

EN EC Declaration of Conformity
The undersigned hereby certifies as the authorized representative of the manufacturer, Husqvarna AB, 561 82 Huskvarna, Sweden, that, when leaving our factory, the unit(s)  indicated below is / are in accordance with the harmonised EU guidelines, EU standards of safety and product specific standards. This certificate becomes void if the unit(s) is / are modified without our approval.

Description of the product: Electric Lawnmower

EasiGlide 300V
EasiGlide 330V
EasiGlide 360V
2006/42/EC
2014/30/EC
2000/14/EC
2011/65/EC| 970483362
970483462
970483562Deposited Documentation: Conformity Assessment
GARDENA Technical Procedure:
Documentation, according to 2000/14/EC
M. Kugler 89079 Ulm Art.14 Annex VI
---|---
Harmonized EN /
Harmonisierte EN-Normen: Ulm, den 12.12.2020| EN ISO 12100
EN 60335-1
EN 60335-2-77 Authorised representative
---|---

** John Thompson**
Product and Marketing Director EUAP

Canada / USA
GARDENA Canada Ltd.
100 Summerlea Road
Brampton, Ontario L6T 4X3
Phone: (+1) 905 792 93 30
info@gardenacanada.com
EG300VEU­20.960.01/1020
Husqvarna AB
S­561 82 Huskvarna
Sweden

Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
Copyright © 2020 Flymo S.A. All rights reserved.
Flymo® and other product and feature names are registered or unregistered trademarks of Flymo S.A.

References

• Anasayfa
• Husqvarna UK | Chainsaws, Lawn Mowers & Garden Tools
• Husqvarna Forest & Garden
• Husqvarna Australia | Tools & Equipment for Lawn, Garden and Forestry
• Husqvarna Brasil
• Husqvarna Ecuador
• Husqvarna Magyarország
• 一瀬製作所 | ステンレス建具のプロフェッショナル■設計・製作・施工
• GARDENA - Garden tools - GARDENA
• GARDENA - Garden tools - GARDENA
• GARDENA - Garden tools - GARDENA
• GARDENA - Garden tools - GARDENA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>