Soar LPSC-026 Record Player Instruction Manual
- June 6, 2024
- Soar
Table of Contents
Soar LPSC-026 Record Player
BEFORE USE
- Choose a safe location and avoid placing the unit in direct sunlight or near any heat source.
- Avoid locations subject to vibrations, excessive dust, cold or moisture.
- Do not open the cabinet as this may result in electrical shock. If a foreign object is inserted accidentally contact your dealer.
- When removing the power plug from the wall outlet, pull directly on the plug, NOT the cord.
- Do not attempt to dean the unit with chemical solvents as this might damage the finishing. A dean, dry doth is recommended for deaning.
- Keep this manual for future reference.
Turntable Parts & Features
- AUTO STOP ON/OFF switch
- 33/45/78 RPM switch – This switch controls the speed of the turntable platter.
- Pitch control knob
- Mode selection knob
- Indicator
- Power on/off and volume control knob
- Headphones jack-to-connect headphones or earphones to enjoy music privately B. stylus-there is a white stylus protector covering on the stylus, remove it before use.
- Tone arm – The turntable comes with a ready to use pre-balanced tone arm and cartridge.
- Platter- Place your record here.
- 45 RPM adapter -used for 45RPM vinyl records
- USB port
- PREV button
- PLAY/PAUSE/ REC button
- NEXT button
- RCA output – Used to connect to external speakers (not included)
- AUX IN jack
- DC IN port- Used to connect power adapter
GETTING STARTED
Fix the dust cover onto the turntable. Firmly and securely insert the DC plug of the adaptor to the DC IN Jack on the back of the unit. Plug the adapter’s AC plugs into a power outlet.
PHONO MODE-VINYL RECORD PLAYBACK
- Turn the mode selection knob to PH.
- Turn the power & volume control knob clockwise. The indicator light will illuminate red.
- Place a record on the turntable platter and select the desired speed (33/45/78) according to the record.
- NOTE : when playing a 45RPM record, use the included 45RPM adapter located in the holder besides the platter(one more 45RPM adaptor can be found in the accessory bag).
- Remove the stylus protector. Open the tone arm clip to release the tone arm. Push the lift lever(it is besides the auto stop switch) backward to raise the tone arm and gently move the tone arm to the desired position over the record. You can turn the pitch control knob to adjust the speed of the platter little by little. The turntable will begin to spin when the tonearm is moved toward the record(when the AUTO STOP switch is ON). Push the lift lever forward to lower the tone arm slowly onto the desired position on the record to start playback.
- If the Auto stop Control Switch is turned ON, the record will stop automatically when finished. If Auto stop Control Sw~ch is turned OFF, the record will NOT stop automatically when finished. Remark: AUTO STOP function applies to most 33RPM vinyl records. However, for very few vinyl records, it will stop when it does not come to the end(in this case, turn the AUTO STOP switch to OFF position and then it will continue playback), or it will not stop when it comes to the end when AUTO STOP is ON.
USB RECORDING
Plug your USB stick into the USB port. During the vinyl records playback, press the REC button and the indicator will flash red and blue alternatively. The vinyl recording starts. Press SPLIT button when recording, the current record will be cut off and automatically stored in a file. Press SPLIT button again and it will generate another file. Press the REC button to stop the recording. The indicator will becomes red during recording, and the recorded files(MP3 format) will be saved in the USB stick.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>