DITRIO InfiColors M12R LED Lights Kit User Manual
- June 6, 2024
- DITRIO
Table of Contents
DITRIO InfiColors M12R LED Lights Kit
Specifications & Parameters
IM,after i a I’: Sil iron,e LED model: SMD RGB 5050 input Voltage,: DC 12V
1(Workable between 10-ESV) Wattage: Max1imum 50 w S,service Life: 510,000
Hours Control: MethodRF remote,, e,ffe,ctive, ·within 30 ft
✓ Standard Wattage per LED: 0.2 w
✓ Maximum current: This value is dynamic, depending
on the colors, modes; and b1rightness that I’ve set ..
• Sol1id white color: 0.5 …… 2.0 A
• ,Q,ther sol id colors: 0.3 – 0.9 A
• Fllash, Strob,e, Fade & Sm,o,oth: 1.0 – 2,.0 A
WARNING
Always use the kiU switch to turn off the LED kit when you don,t ride your
bike,, especially for days and weeks. This heps you prevent battery drain.
Test before Installation
- First of all, do ai lighting test bef·ore installation to make sure everything is fine.
- find,a power source with D1C VZV (typ1icaUy the batt1ery of your bike has this vo-tag,e)
- Connect the red wire to the PO, positive, and the black wire to the negative
- lE D strips will go on after ‘YOU turn it on by pressing the push butt1on on the kil. I switch for the 1st ti me
- . Keep the red wine,e, and black wire connected, use the blue wilre to touch the positive,
- Check whether LED s,trips go red, and this is for the brake Ught feature
- After you confirm everything works correctly, simulate installation to see whether th1e wires flt aU your target spo1ts,
- llf you see1 a prob,l, em, turn to the back cover of this manual, pick a way to contact D!ITRI01 team, and w·e answer the same day
Conceptual Wiring Diagram
Primarily, the conceptual wiring diagram demonstrates the position and
relation among differ1e nt parts. it helps you,u und1erstand how to connect
parts 1correctly
Be1low is a list of com1ponents indicated with numbers 10n the wiring diagram.
- Contro1 1 box with attached copper wires
- Kill switch with,a push button
- Signal wire for brake light feature
- 1-2 way splitters x 3
- 1-3 way splitters x 4
- @ LED1 strips x 12, 3 sizes
- Ba1ttery fair pow,er supply
- You do1don’t have to install LED strips exactly the same as this la.yout.
Adjust the positions/connection of LED strips to fit your bike, if you have a
different installation co1nieept. Yo,u can add additional items to this
system too.
✓ lt 1d be g1ood to map your lay, out and che1ck wires’ le,ngth before
installation.
✓ Make sure you have an n, necessary items in your hand.
- Brightness up
- Brightness down
- Music mode
- On /Off
- good colors
- ® Lig1hting effects
A useful tip1 for i1n1creasing batteries’ service hours:
✓ Press remotes’ buttons quickly fai r adJustment
✓ Do N01T press and hold any button
✓ Short presses use battery dr, dramatically less than long-press,es
If you need a replacement, cement remote,, pl1eas1e scan this 1QR code. You can pair it to1 your old control box. D,don’t need to replace other things.
SoUd colors
short press: – 1st o 18th for a so:11d color
– 19th o 20th for colors to bea & fade b). long press:
– Change brightness
Lighting effects – 1st press for flashng Ught
– 2nd press for fading light p.s. When colors beat & fade, press B o cha1nge
speeds
Music Mode· ON I OFF
This k1eyieha1in fob has 18 solid col1ors, which airr1e avai1lablle by the 1st
-18th presses on
key A:
• Re1d, Dark Blue, Purple, Green, yellow, Ice B(ue, Orange, Purpl1e, Light
G1r1een, White,. Cyan, Light Pu1rple, Blue, Ice White, Warm White1 , White,
lice Gre1en and Yellow Green
✓ You can put the lights into fats.h.ing and fadingmi0d1es by pres. sing key A
for the 19th and 20thti1me1•
Key B:
✓ The key B is 1mostly for change, I ng lighting effects
✓ it means, after you s1ele 1ct a co1l1or by key A,, then you can use key B
t10 make the Ught flash 01r fade.
- Switch o,n / give electricity t10 the LED light stri1ps
- You will notice, the, LED strips ·flash,, and then th1ey goes off automatically
- Next, the, ey come on again by them1sefves,. and this is the time fair synchronizing
- First, press button Brightness Up and then button Brightness D1own one by one within 3 seconds
- Notice that LED strips flash for 2 time if correctly resynced
- Take the same procedures t,o resync the 4-key remote
- Just replace the 2 brightness keys with the A & B keys
- If you miss the 3 seconds for resyncing, don’t press the buttons repeatedly, but power the system off and try again from the beginning
- If ‘Y10 U have an old RF remote from1 another brand, y1ou may not be able to sync it to 1our control bo,x
- THE same logic for ours, and very Ukely don’two1rk with a control box from another brand
- To make RF remote,tes work, y1ou wiU needs the right programs, and circuits inside contr,ol boxes. Otherwise, they w, don’t sync to each other.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>