Shenzhen Yingbojingkong Technology IB-IBT01 Wireless Bluetooth BBQ Thermometer User Manual

Shenzhen Yingbojingkong Technology IB-IBT01 Wireless Bluetooth BBQ

Thermometer

FAQ

1. Why the probe display, inaccurate tampandure? Such a 572F ar the IICl’Nl’I display ‘?
   Answer: First please check the probes whether finally inserted in the unit and you may hear a click sound. Customers really need to push it hard in. Then change probes to insult in different pona to check if the probe itself has a problem. Please make sure your probes are firmly inserted, otherwise will diaplay’—–• even if the cell phone pair with Bluetooth successfully.

2. Scan I put this unit in high-temperature places?
   Answer: No, ii can’t The plastic back magnet temperature should not be over 80-C/176’F. Otherwise, the unit will melt Probe temperature range: 32’F – 572’F; (Sholt-time menurenw,t); 32’F-4U”F (continuous monitoring)

3. WITH cell phone can not sean:h the app?
   Answer. Pl1111S1 make sure your GPS is on(Android phone).

4. WITH I need a 4 number pin code? What’s c: connect 5teps lo pair with a cellphone?
   Answer: This unit no need for pin code. Here are two solutions: First, for some customers who have used our lnkbird other thermometers before, you hlVII to delete the before the record, then to pair with this product. Because one cell phone can only connect on• unit at on• time. Second, The correct procedure is to activate your Bluetooth and open GPS service on your phone first, open the BBQGO APP to press the bottom start button 10 searches, then press the on the button of your unite for about 3 seconds it should connect

5. s.can – lrit be linked up to multiple phones or one phone connected with multiple units?
   Answer: One phone can only connect with one unit at on• time. 6″ 9 the probes and wire waterproof
   Answer: No. Only the meat ends are waterproof.

6. Does thiS tampan,. alarm fln:tion7
   Answer: Yes.

7.  Is there any i,aphing or NYe of previous cook data? Answer: It can only display th, current cooking data. Which can’t be saved for download

Get to know the device

• Probe Sockets
• Probe with cable
• USB Charge Cable (Length:50cm)

This device provides 4 probe sockets, which enable you to monitor up to 4 food at the same time.

Charge the device

This device uses a built-in non-detachable lithium battery, usable charging, and power supply. Please note that:

1. The battery cannot be removed
2. takes about two hours to fully recharge.3

Download the APP

Search the keyword “bbq go· in Appstore or Google Play or scan the following QR code with your phone. Download and Install for free.

Make sure your phone meet the requirements: iPhone 4S, and later models;  iPod touch 5th, iPad 3rd generations, and later models, all iPad mini; Android devices running version 4.4 or later, with blue-tooth 4.0module

Install the probes

The device will keep scanning the sockets when its power is switched on, the probe indicators will blink one by one from 1 to 4 where probes are plugged in Then Insert the probes Into the food, make sure the front tip of the
probe is in the center of the food to get accurate temperature

Pair with your phone

1. Press and hold the power button on the device for 3 seconds to power it on.
2. Turn on your cell phone bluatooth
3. Launch the app, and follow the instructions In the app to pair and activate the device.
4. Connected successfully.

Once paired the device with your phone, you don’t need to do it again, unless you change to other phones.

• The max temperature is D-300 •ct32• F – 572 • F; {Short-time measure-men!); 0-250″C/ 32′ F-482 • F (continuous monitoring),if exceed this temperature, the probe and the wire be burned-out. Especially, do not directly put the wire or the probe In the bu ming flame or heating tube
• Do not submerge the probe and the wire in water for a long time, which may cause inaccurate temperature measuring.
• Do not strongly squeeze the probe and the wire, which may break the plastic-covered wire on It and cause a short circuit on the polarity.
• Remove the silicone cover on the end of the sensor before using it.

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions

1. This device may not cause harmful interference;
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority, to operate the equipment
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful Interference to radio or telavlslon reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver Is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>