TRENDNET AX1800 Dual Band Wi-Fi 6 Router Installation Guide

June 6, 2024
TRENDnet

TRENDNET AX1800 Dual Band Wi-Fi 6 Router

Ancatus

Front indicator

Indicator status description

If the indicator light is not normal, please check if the connection is correct,

Cable and art connection instruction

Configuration instruction

Connect the device

Connect the LAN interface and WAN interface (community broadband) on the router with an Ethernet cable (network cable).

Connect to Wi-Fi

Use a laptop or mobile phone to search for the SSID corresponding to the Wi-Fi network. on the nameplate at the bottom of the device and join it.

Set up the network

Visit 192.168.10.1 through the browser to complete the se, and log according to the account password on the bottom nameplate.

Log in  configuration interface

Power on the router, and connect the mobile phone/computer to the router with a network cable or wirelessly.

Open the browser and enter 192.168.10.1 or wifi.CMCC/ to enter the login interface.

Enter the user name USER and the configuration management password to log in. For the configuration management password, see the nameplate at the bottom.

Modify WIFI name and password

Modify 2.4g WIFI name and password

  1. Select “Network”–+ “WLAN Network Configuration”

  2. Modify the 2.4g WIFI name in “SSID”, and modify the WIFI password in
    ”WPA pre-authentication shared key”

  3. After the modification is completed, click “SAVE” to save it and complete the modification of the wifi name and password

Modify WIFI name and password

Modify 5g WIFI name and password

Select “Network”–+ “WLAN 5g Network Configuration”

Modify the 5g WIFI name in “SSID”, and modify the WIFI password in
“WPA pre-authentication shared key

After the modification is completed, click “SAVE” to save it and complete the modification of the wifi name and password

Environmental re requirements

This form is compiled in accordance with the provisions of the SJ!T11364 standard.

0 indicates that the content of this toxic and hazardous substance in all homogeneous materials of this part is below the limit requirement of the G B / T standard.

X indicates that the content of the toxic and hazardous substance in at least one of the homogeneous materials of the part exceeds G B / T 2 6 5 7 2 The specified limit requirements.

This table shows the hazardous substance information contained in this device. The hazardous substance information of the parts is based on the information provided by the supplier and the internal inspection results. The hazardous substances contained in some parts are impossible to replace under the current technical standards.

The number in this logo indicates that the EFUP of the product under normal use is 10 years. some components may have an EFUP mark and the EFUP shall be subject to the number in the mark. due to different models, the product may not contain all the above components except the host. please refer to the actual sales configuration of the project.

Recycling

This product bears the selective sorting symbol for waste electrical and electronic equipment(WEEE). This means that this product must be handled according to European directive 2012/19 /EU in order to be recycled or dismantled. This will minimize the negative effects on the environment and human health resulting from the possibility of the presence in the equipment substances, mixtures and hazardous components.A user can give the
product to a competent recycling organization.to WEEE collection points or to a distributor(in accordance with local regulations).

FCC NOTICE:

This equipment has been tested and found to comply with the limits for a Class 8 digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  •  Reorient or relocate the receiving antenna.

  •  Increase the separation between the equipment and receiver.

  •  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

  • Consult the dealer or an experienced radio/TV technician for help.
    Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is
    subject to the following two conditions:

  • This device may not cause harmful interference, and

  • This device must accept any interference received, including interference that may cause undesired operation.
    The equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body,

Repair description

Warranty description

  1. Thank you for purchasing our products. To protect the rights and interests of the purchaser, please fill in this card carefully, and read the following warranty terms carefully.

  2.  Please keep this warranty service card properly. If the warranty service card is lost, it will not be reissued. Please be sure to keep the invoice or copy or relevant valid proof of purchase. If you cannot provide valid proof of
    purchase. Then the product warranty period will start from the date of manufacture.

  3.  This warranty card must be provided at the time of warranty.

  4.  The Information filled In this warranty card should be true, otherwise, It will be invalid.

  5.  If the host of this product is sold within 18 months, free after-sales maintenance service is guaranteed if a hardware failure occurs under normal use conditions.
    The company has the right to charge maintenance service fees if the following factors are involved:
    Due to natural disasters (floods, fires, earthquakes, lightning strikes, typhoons, etc.)
    Damage caused by careless use:
    Disassemble, repair, or send the product to a repair center that is not certified by the company for inspection and repair;
    The company’s warranty identification label is torn or cannot be identified, the warranty service card is altered or the product is inconsistent;
    4. Other problems and malfunctions caused by abnormal use.
    The company will strictly abide by the Three Guarantees policy formulated by the state for warranty service.
    The right to interpret the warranty regulations and contents belong to our company and are subject to change without notice.
    Customer Service:support@ancatus.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

TRENDnet User Manuals

Related Manuals