WDXBE Digital Bass Enhancer Instruction Manual
- June 6, 2024
- WDX
Table of Contents
WDXBE Digital Bass Enhancer Instruction Manual
INTRODUCTION
Congratulations on purchasing the WDXBE you are now the proud owner of the finest and most accurate bass enhancing & restoration system available.
Whether your interest is in Beethoven’s kettle drums, in Miles Davie trumpet or in the percussion of Rap lyrics, the WDXBE would restore the long lost bass notes, with amazing accuracy and clarity.
There’s a dash mount level control unit which permits instant adjustments: weather it’s because your passanger is not as much a “bass-head” as you are or for whatever reason you want to turn it down a bit, this handy knob does the trick.
FEATURES
BASS Driver: The WDXBE contains a Bass Driver circuit that accurately recreates and injects Low frequency information bath into the signal path. What that means in everyday terms is that the Bass Booster will give more bass impact to your best compact discs or even your old tapes.
Bass Equalization Circuit: The WDXBE has a unique equalization circuit that contours the restored bass to your speaker systems.
Dash Mount Remote Control: The WDXBE comes with a dash mountable remote control that allows you to enjoy the effects of the WDXBE without having to leave the driver’s seat. The dash mount control has a LED indicator, this LED will grow brither as you add more bass or dimmer when you decrease it.
Bass Maximizer Indicator: Not only does the WDXBE provide good music to your ears. but it also gives you some visual enjoyment as well. On the chassis of the E5 BE there is one LED that indicates that the system is on.
PFM Subsonic Filter Switch: This unique feature is legendary with its ability to fine tune the bass response of any system, why waste power on nasty subsonic information when the PFM Subsonic Filter Switch can help you clean things up?
Bass Output Control: The WDXBE has the ability to produce large amounts of deep, mind shattering bass without damaging your speakers. The Bass Output Control circuit allows the WDXBE to maximize the bass output of any auto sound audio system while restraining destructive bursts.
FUNCTIONS
THE OUTSIDE
- Inputs: The inputs of the WDXBE use a balacenced input circuit to help minimize induced noise. They are also designed to handle very high signal voltage, up to 15 volts.
- Outputs: These RCA connectors should be connected to the next component after the WDXBE as a crossover, equalizer, or amplifier. Just remember, the WDXBE should go inline before a crossover.
- Dash Remote Control
- Power Connector
- BASS Controls: These 2 knobs control the Bass functions of the WDXBE. The SWEEP knob allows you to pick the center frequency that you want the WDXBE bass restoration circuit to maximize. The WIDE knob adjusts how wide of a frequency range the WDXBE will affect.
- Power on LED
- SUB VOLUME CONTROL
- ash Subsonic Control: This knob controls the subsonic frequency from 35 Hz to 80 Hz.
ELECTRONIC CONNECTIONS & WIRING
Power Connection
B+(12V): Connect a red wire to the car battery of other power source.
REMOTE: Connect an orange wire to remote activation (12V DC) wire of car stereo or equalizer.
GND: Connect a black wire to the car chasis for ground connection.
SIGNAL CONNECTION
Note: For signal connection, the output RCA connectors should be connected to the next component after the WDXBE, such as a crossover , equalizer, or amplifier, just remember, the WDXBE should go inline before a crossover
Adjusting the Bass Controls
The bass response in a system is affected by four factors:
- The acoustics of the vehicle
- The locations of the speakers
- The music on the tape
- Speakers and speaker enclosures.
Because of the variations in the recording process, we developed the WDXBE to restore any low frequencies lost during the recording process; however, the acoustics of various enviroments are different. The Sweep control allows you to select a center frequency (the frequency most affected) between 27 and 63 Hz. The width controls them to allow you to control the shape of the filter centered on the sweep frequency.
Setting the Bass Output Control
The WDXBE is a powerful bass processor. This device is equipped with several output voltage selections, if you should need to change the settings, please use the chart below for guideance as recommended list to the factory setting before changing your Bass Output settings.
Recommended Settings
| Setting | Amplifier Input Voltage | Minimum Speaker Size |
|---|---|---|
| 2.5 Volts | 3.0 Volts or less | 8″ |
| 5.0 Volts | 5.0 Volts or less | 10″ |
| 7.5 Volts | 7.5 Volts or less | 15″ |
| 10 Volts | 10 Volts | 15″ |
SPECIFICATIONS
Maximum input Level…………………………. 15V rms
Maximum Output Level……………………………….. 13.2V peak
Frequency Response………………………………. 10 Hz -35 KHz
T.H.D………………………………………….. 0.0025%
Signal to Noise Ratio…………………………. 133 dB
Balanced input Noise Rejection……………………………. >62 dB
input Impedance……………………………… 10K ohms
Output Impedance…………………………………… 150 ohms
Power Supply……………………………. High headroom PWM
Power Draw…………………………………… 150mA
TROUBLE SHOOTING GUIDE
If the Unit does not turn on, and/or the power indicator LED is NOT illuminated, do this:
-
Check and make sure that B+ and GND are not reversed
-
Check that all power wires are properly connected and have the appropriate potential (11 – 16 volts)
-
Check that the fuse is intact.
If you experience high audible distortion or low output volume: -
Check that the input and output levels are set correctly. Input should match the source and output should match the sensitivity of the host.
-
Check the crossover settings, make sure they’re correct; for high “Q” systems set it to 1 octave or more.
If you experience whining or engine noises: -
Verify that the GND connection is secure, the conductor (wire) is not too thin and unnecessarily long.
-
Check that the B+ wire is not too thing and unnecessarily long.
-
Change the power source; try taking power from a different point.
INSTALLATION
LIMITED WARRANTY
DB Drive™ warrants any products purchased in the U.S.A. from an authorized DB Drive™ dealer. All products are warranted to be free from defects in material and workmanship under normal use and service for a period of one (1) year when the unit is installed by an authorized DB Drive™ dealer. Non-authorized dealer installed products carry a one (1) year parts and labor limited warranty. This warranty applies to the original purchase only.
DB Drive™ will either repair or replace (as its option) any unit that had been found to be defective and under warranty provided the defect occurs within: One (1) year, if purchased through an authorized DB Drive™ dealer with original proof of purchase.
This limited warranty periods do not extend to units having been subjected to misuse, abuse, neglect, or accident. Products that in DB Drive™ judgment shows evidence of having been altered, modified, or serviced without DB Drive™ authorization, will be ineligible under this warranty.
To obtain warranty services please contact your retailer or visit our website at www.dbdrive.net for more details.
DB Research L.L.P. • 302 Hanmore Industrial Parkway • Harlingen, TX 78550 Ph: 877-787-0101 • Tech Support: support@dbdrive.net
Designed and Engineered in the U.S.A
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>