JOCEL JAG014146 Portable Gas Heater Instruction Manual

GAS HEATER

JAG014146

FOR ENERGY SAVING, THIS PRODUCT IS NOT SUITABLE FOR PRIMARY HEATING PURPOSES
Read the Instruction Manual carefully.

READ INSTRUCTIONS CAREFULLY: READ AND FOLLOW ALL INSTRUCTIONS. PLACE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE. ONLY USE IN A WELL VENTILATED AREA
WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY. A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE. PERSONAL INJURY OR LOSS OF LIFE

TECHNICAL CHARACTERISTICS

Medium: 2,9kw
Minimum: 1.5KW
Consumption;| Maximum: 305g/H
Medium: 207g/h
Minimum: 110g/h
Ignition system:| Piezo-spark ignition
Cylinder Type:| UP to 15kg cylinders

WARNING:

1. THE APPARATUS IS NOT READY FOR THE PHYSICALLY WEAK, SLOW RESPONSE, OR MENTAL DISORDERS (INCLUDING CHILDREN) TO USE UNLESS IT BEARS RESPONSIBILITY FOR THE GUIDANCE OF SAFETY OR SAFE USE OF THE HELP.
2. CHILDREN SHOULD BE MONITORED TO ENSURE THEY DO NOT PLAY APPARATUS.
3. THE HEATER IS NOT LOCATED IMMEDIATELY BELOW A SOCKET OUTLET.
4. THIS HEATER IS NOT EQUIPPED WITH A DEVICE TO CONTROL THE ROOM TEMPERATURE. DO NOT USE THIS HEATER IN SMALL ROOMS WHEN THEY ARE OCCUPIED BY PERSONS NOT CAPABLE OF LEAVING THE ROOM ON THEIR OWN UNLESS CONSTANT SUPERVISION IS PROVIDED.

SAFETY PRECAUTIONS:

| 1. Always use the heater in accordance with instructions supplied with each heater. Keep instructions in a safe place.
2. DO NOT place clothes or other materials on the heater. This could cause fire risk and/or affect the efficiency of the appliance.
3. DO NOT position the heater close furniture.
4. DO NOT move the heater from room to room when lit.
5. DO NOT position the heater close to walls, furniture, net curtains, bed linen, or any other inflammable materials as this could result in the risk of fire. The following minimum distances should be respected; 50cm from the side, 100 cm from the front. ALWAYS face the heater towards the center of the room. The heater should be positioned on a level surface at all times.
6. If a leak is suspected, turn the gas off at the cylinder. DO NOT disconnect the regulator. Check all connections. Slowly turn the gas on and brush the connections with soapy water or liquid detergents a gas leak will form bubbles. If a leak is found, turn the gas off. DO NOT use the heater again until it has been checked by a competent person in accordance with the Gas Safety (installations and use) Regulations 1998.
---|---

USING ENVIRONMENT:

Your heater consumes oxygen while it is in function. For that reason, adequate ventilation should be provided in rooms in which the heater is used. This ensures the removal of products of combustion and allows the entry of replacement air.
Adequate ventilation should considerably reduce the possibility of condensation occurring. The following table shows the smallest sizes of room suitable for each heat setting and the ventilation.

FOR CATALYTIC HEATER MODELS:

Number of heaters continuously IN USE| ROOM SIZE| VENTILATION
---|---|---
Low level|
1| 40 cubic meters – 4m•4m2.5| 40cm2| 1
2| 70 cubic meters – 7m•4m2.5| 70cm2| 2
3| 105 cubic meters – 105m4m2.5| 105cm2| 3

1. This appliance requires a hose and a regulator (not supplied).
2. Only use in well-ventilated areas.
3. Do not use in vehicles, caravans, or auto caravans.
4. Do not attempt to use in high-rise flats, basements, bathrooms, or bedrooms.
5. Do not use your heater while sleeping.
6. Do not store flammable liquids or material near the heater.
7. Do not expose the gas bottle to the full summer heat nor too near any other heat source.
8. Do not place a heater in use near curtains, furniture, wood paneling, or combustible material which can deteriorate with heat.
9. While in use, ensure that children do not approach the heater.
10. Do not move the appliance when in use; the safety device may be activated by knocks or
11. This appliance should be tested for leaks before initial use and whenever the cylinder is re-connected.
12. It is important that all gas connections have been correctly made to prevent any leakage. Do not use a naked flame to test for leaks. Call your supplier to ask for support.
13. Always use your cylinder always in an upright position.
14. Always turn off the regulator control when the heater is not in use.
15. When lighting your heater for the first time or after a period of time has passed since the last use, light the heater outside and burn outdoors for 15 minutes.
16. The guard on the appliance is to prevent the risk of fire or injury from burns and no part of it should be permanently removed. It does not give full protection for young children or the infirm. We would recommend a fireguard to be fitted.
17. Only connect the apparatus if the voltage indicated on the type plate corresponds with the mains voltage.
18. In order to avoid overheating, do not cover the heater with towels curtains, or suchlike.
19. Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord
20. Turn off the appliance and unplug from the outlet when not in use and before cleaning. Allow it to cool down.
21. If the supply cord is damaged, it must be replaced by a service agent or equivalent qualified persons otherwise it may cause a hazard.
22. To protect against fire, electrical shock, and injury to a person, do not immerse the appliance, power cord, plug in water, or other liquid
23. This appliance is for indoor use only.
24. Do not handle the plug with wet hands.

The appliance has to be unplugged from the wall socket, using the damp cloth to wipe the enclosure, and then dry it with a dry cloth.

FAULT FINDING CHART

Technical problems

|

Problem

| Problem Causes|

What To Do

---|---|---|---
Smell of gas| Regulator & Hose connection lose| Use soap form for leakage control, check all connection systems replace defective parts
Valve & pipe connection lose
Pipe broken
The missing piece of ceramic
fireclay| Inspect the perimeter of each plaque and locate the place where some fireclay has been displaced.
Repair with PYRUMA and leave to set for Approx. 48 hours.
Inefficient combustion on
ceramic burner| Dirty gas inlets| Please clear injectors with Air
If there is no ignition| Defective Spark – Plug| Check cable of the igniter, & replace defected igniter if necessary
Defective igniter cable| Check spark — plug and connections, & replace defected igniter if necessary
Burner flame has extinguished during operation| Run out of gas| Change the gas bottle
The thermal element has not been warm enough| Try restarting
Wing or draught has extinguished the flame| Put the appliance out of reach of wind and draught, let it cool down for a couple of minutes, and try to restart it
Faulty thermocouple| Replace the faulty thermocouple
Faulty magnetic valve| Replace the magnetic valve
General problem| The heater does not remain alight when pressure is released from the ignition button| Wrong power setting at first process| Turn the control knob at ” START”
Position and press for 10 seconds, whilst pressing the Piezo igniter key to lit
The heater could not be turned on| Did not connect the gas regulator to the gas cylinder heater| Connect heater to the gas cylinder and ensure there is no smell, then follow the Instruction to turn on the
Gas cylinder control is closed| Please turn on the gas cylinder control

For your safety purpose, call the local service center if you have problems.

REPAIRS SHOULD ONLY BE CARRIED OUT BY A COMPETENT PERSON IN ACCORDANCE WITH THE GAS SAFETY (INSTALLATIONS AND USE) REGULATIONS 1998

CONSTRUCTION AND FUNCTION

1. Igniter
2. Gas control knob
3. Front panel
4. Side Panel
5. Protection Guard
6. ODS (Oxygen Depletion Sensor and pilot light)

CONNECTING THE CYLINDER

1. Place the gas-filled cylinder into the back of the heater.

2. Clip-on the gas regulator to the gas cylinder.

3. Turn the regulator on.

4. The regulator is not supplied please contact your gas dealer to advise of the correct type for the gas cylinder being used.

5. IMPORTANT TEST FOR LEAKS:
   This must be carried out in a well-ventilated area, free from naked flames and any other sources of ignition. With the regulator connected to the cylinder turn on the regulator control. Brush all hose connections, pipe connections to the valve, and gas cylinder valve with a 50:50 solution of detergent and water. A stream of bubbles forming indicates a leak. If a leak is found turn off the regulator and disconnect the regulator from the bottle and remove the gas cylinder outdoors or to a well-ventilated area. Contact your gas supplier for assistance. DO NOT USE THE HEATER.

6. After leak testing is satisfactorily carried out close the back door of the heater. It may be necessary to move the heater slightly to allow the regulator and hose to fit in the back without kinking the hose.

HOW TO CHANGE A CYLINDER

1. Unplug the heater before taking out the cylinder.
2. Tum off at the regulator and allow the heater to cool fully before removing and replacing the cylinder. Do not attempt to replace the cylinder whilst the heater is still running.
3. Cylinders must be replaced in a flame-free environment.
4. Do not smoke while changing the cylinder.
5. When you need to replace your empty cylinder, turn the gas off at the valve or regulator of the cylinder and take the empty cylinder out of the heater.
6. Remove the regulator from the empty cylinder.
7. Following the steps described under “connecting the cylinder”, connect a new cylinder.

ELECTRIC QUARTZ OPERATION GUIDE

(a) Take out the heater from the carton carefully. Please save the carton for off-season storage.
(b) Make sure the heater is off position “O” before switching on.
(c) Connect to a cylinder with a regulator and hose (not supplied).

GAS HEATER OPERATION GUIDE

1. LIGHTING INSTRUCTION
   The heater has three settings. Lighting (Pos.1) and Minimum (Pos.2); Medium (Pos.3) and Maximum (Pos.4)
   Place the gas-filled cylinder into the back of the heater.
   Clip-on the gas regulator to the gas cylinder.
   Turn on the gas regulator.

2. LIGHTING
   Press the control button for 10 seconds at Position 1, at the same time press the piezo igniter key to light with the thumb finger of the left hand, continue this procedure until the pilot ignites, approximately after 20 seconds leave the control button. At this stage, if the pilot is alight, it means that the heater is at the minimum position (Pos.1). If the pilot flame goes out please repeat this procedure.

3. HEAT SETTING
   To change from minimum to maximum gently press the control button and turn it to position 3.
   To change from maximum to medium gently press the control button and turn it to position 2.

4. TURN OFF THE HEATER
   Turn and press the control knob to the LIGHTNING position. Then turn off the valve on the gas cylinder. If the heater is not used for a period of time, disconnect the regulator from the cylinder.

WARNING

• Read the instructions before using this appliance.
• The apparatus is not ready for the physically weak, slow response, or mental disorders (including children) to use unless it bears responsibility for the guidance of safety or safe use of the help.
• Children should be monitored to ensure they do not play apparatus.
• Use an appropriate regulator (not supplied), ask your supplier to get one.
• Never attempt to light if the hose is loose or damaged in any way.
• Do not press the ignition button for more than 40 seconds.
• Never disconnect the regulator while the cylinder valve or regulator is open.
• Do not change cylinder in areas in which open fire exists.
• Do not expose your cylinder to extreme heat.
• Do not store any other cylinders in the room in which your heater is used.
• Do not insert your finger or any other material through the front panel of the heater.
• Leave at least a 1-meter distance between your heater and the other heat source.
• Do not let unauthorized persons tamper with your heater.
• Do not place appliances under electrical socket outlets.
• Do not use the heater in bathrooms, showers or swimming pools, or leisure vehicles such as caravans or auto caravans.
• This heater must not be used without a gas cylinder fitted for stability purposes.
• Do not cover your heater. Fabrics, clothing, hangings, net curtains, bed linens, and other flammable materials may ignite if placed against the outlets of your heater.
• In the event of leakage, the appliance should be turned off at the regulator switch-on valve and the regulator disconnected from the cylinder.
• After use turns off the appliance at the gas container valve.
• Only use in a well-ventilated area.

STORAGE

1. Disconnect cylinder.
2. Store cylinder in a well-ventilated area away from combustible material. Storage preferable be in an outhouse but must not be in a basement or high-rise flat.
3. The heater should be covered in a dry, dust-free area in its original packaging.

CLEANING

1. Make sure to unplug the heater before cleaning.
2. Turn off your gas supply at the regulator.
3. Use a damp soapy wrung cloth clean the exterior and cylinder storage area of your heater.
4. Make sure that no water gets onto the burners or pilot/light area. Wipe the heater dry before use.
5. Don’t use abrasive cleaners as they may damage the quality paint finish.

MAINTENANCE

1. Check flexible tubing between regulator and heater regularly and replace if perished, worn, or In any case, replace tubing taking into consideration the expiration date.
2. It is recommended that the heater be serviced every year by a competent person in accordance with the Gas Safety (installations and use) Regulations 1998.
3. If any parts need replacing, they should be replaced only with the correct parts supplied by the original manufacturer.

Information requirements for gaseous/liquid fuel local space heaters

Model identifier(s): JAG014146
Indirect heating functionality: NO
Direct heat output: 4.2 (kW)
Indirect heat output: NA
Fuel| | | Space heating emissions (3)
NOX
13+(28-30/37)| gaseous| 2830/37 mbar| (mg/kWh input) (GCV)
item| Symbol| Value| Unit| | item| Symbol| Value| Unit
---|---|---|---|---|---|---|---|---
Heat output| | Useful efficiency
Nominal heat output| P(NOM )| 4.2| kW| | Useful efficiency at the nominal heat output| n (nom)| 91|
Minimum heat output| P(MIN)| NA| kW| | Useful efficiency at the minimum heat output| ri (min)| N/A| %
| | | | | | | |
Auxiliary electricity consumption| | Type of heat output/room temperature control
at the nominal heat output| el| 0| kW| | single-stage heat output, no room temperature control| NO
at the minimum heat output| el| 0| kW| | two or more manual stages, no room temperature control| YES
In standby mode| el| 0| kW| | with mechanic thermostat room temperature control| NO
| | | | | with electronic room temperature control plus day timer| NO
| | | | | with electronic room temperature control plus week timer| NO
| | | | | Other control options (multiple selections possible)
| | | | | room temperature control, with presence detection| NO
| | | | | room temperature control, with open window detection| NO
| | | | | with distance control option| NO
Permanent pilot flame power requirement| | |
Pilot flame power requirement (if applicable)| P| 0| kW| | |

WARRANTY CONDITIONS

1. The warranty is valid only on the presentation of the invoice of purchase.
2. This WARRANTY is limited exclusively to parts substitution ineffective due to faulty manufacture, made in our workshops.
3. The elimination of several faults of the scope of the guarantee is made for repair or replacement of defective parts, according to the discretion of our technical services. Defective parts are our property.
4. Are not covered under warranty damage caused by transportation, neglect or poor use, improper assembly or installation, as well as external influences such as lightning strikes or power, flooding, humidity, etc…
5. Lose warranty, all appliances that are not being used according to the instructions, or connected to FEEDING NETWORKS do not guarantee a constant voltage of 220/240V.
6. The warranty does not cover damages for personal injury or damage caused directly or indirectly in any capacity whatsoever.
7. This warranty terminates when it is found to have been undergoing repairs, alterations, or interventions by any person not authorized by Jocel.

THE WARRANTY EXPIRES

1. If the appliance has not been installed by an Accredited Technician.
2. Exceeded the period of 2 years for home appliances and 06 months for industrial appliances, the warranty expires and assistance will be made by charging the costs of manpower, according to current fees
3. With the modification or disappearance of the nameplate of the appliance.

**TECHNICAL ASSISTANCE

**

For technical assistance requests, our services are available through the following contacts:

Telef. 00 351 252 910351
Fax: 00 351 252 910367
E-mail: assistencia@jocel.pt
http://www.jocel.pt

SEDE:
Rua Alto do Curro, n.° 280
4770-569 S. COSME DO VAL
V.N. de FAMALICAO
Telef: 252 910 35012
Fax: 252 910 368/9
email: jocet@jocel.pt
http://www.jocel.pt

DECLARATION OF CONFORMITY

We declare on our own responsibility that the machine indicated below

Product
Brand
Model| GAS HEATER
JOCEL
JAG014146
---|---

Complies with the following European directives and standards implementation

Gas Appliances| (EU) 2016/426
2009/125/EC
2015/1188
2015/1186| EN 449:2002 + A1:2007
---|---|---

Documents / Resources

| JOCEL JAG014146 Portable Gas Heater [pdf] Instruction Manual
JAG014146, Portable Gas Heater
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>