GI DRC-400 Remote Control User Guide

DRC-400/425
UNIVERSAL REMOTE CONTROL

OVERVIEW

The General Instrument DRC Universal Remote Control will control up to four devices, including GI Cable Converters (i.e., DCT-1000, DCT-1200, DCT-2000, and  CT5000),
most TVs and VCRs, and auxiliary components.
The DRC requires two fresh AA alkaline batteries and easy programming to control all functions of your Cable Converter, as well as all of the basic functions of your other original remote controls. For best results, please read and perform all instructions listed here. Also, keep these instructions for future reference.

FEATURES AND FUNCTIONS

Use the DRC mode keys (i.e., AUX, VCR, CABLE, or TV) to control the desired device. When pressed, the selected mode key will light, confirming your choice. Use the other
keys to perform desired actions (see the following key chart).
NOTE: The selected mode will remain active until you press another mode key.

AUX, VCR, CABLE, or TV| Press AUX, VCR, CABLE, or TV once to select a home entertainment component to control.
---|---
POWER| Press POWER once to turn on or off the selected home entertainment component.
HELP| Press HELP once to display the help screen.
MUTE| Press MUTE once to turn the sound off or on.
| Use PAGE s (or PAG E t ) to page up (or down) through menu screens and the program guide.
LOCK/PPV| Use LOCK/PPV to restrict viewing of selected programs or to view the PPV menu.
EXIT| Use EXIT to exit the menu or guide.
INFO| Use INFO to display current channel and program information.
| Use cursor keys to move the cursor in the program guide and menu screens.
| Use OK/SELECT to select menu options, PPV events, and to tune programs from the program guide.
GUIDE| Use GUIDE to display the program guide.
MENU| Use MENU to display the main menu.
VOLUME| In TV or CABLE mode, use VOLUME + (or VOLUME -) to raise the (or lower) sound volume.
CHANNEL| Use CHANNEL + (or CHANNEL -) to select the next higher (or lower) channel.
LAST| Use LAST to recall the last channel or go back to one screen in the menu.
FAVORITE| In the CABLE mode, press FAVORITE once to display preset favorite cable channels.
| These functions are set by your cable system operator.
| Use the keypad (0 ~ 9) to directly select channels (e.g., 09 or 31).
TV/VCR BYPASS| Press TV/VCR BYPASS once to switch VCR to view TV or tape (not supported by all applications).
| Use ENTER/MUSIC to display a menu of digital music channels, or to enter channels on some TV models.
| In the VCR and TV modes, use the STOP, PAUSE, P L AY, R EW. , RECORD, and F.FWD.
keys to control VCR. To record a program, press RECORD once.
---|---
| In the CABLE mode, press DAY> (or <DAY) once to move the program guide ahead (or
back) 24 hours.

*NOTE: Functionality of the LOCK/PPV and SELECT/OK keys are dependent on the software and the model of the converter.

INSTALLING BATTERIES

1. On the DRC’s back, pull back the battery cover and remove it.
2. Obtain two (2) fully charged AA alkaline batteries. Match the + and – marks on the batteries to the + and – marks in the battery case, then insert the batteries.
3. Push the battery cover back into place.
4. Test the unit by pressing POWER and any mode key (e.g., AUX, VCR, CABLE, or TV). If the batteries are inserted correctly, the selected mode key will be lit.

NOTE: Removing the batteries WILL NOT require you to reprogram your DRC. A selected mode key will blink two times with each key press when batteries need replacing.

PROGRAMMING TV CONTROL

1. Turn on the TV.

2. On the DRC, press and hold the TV (at least 6 seconds) until you see the programming mode start.
   Each mode key light will turn off and on sequentially, starting with AUX on through TV, and the sequence will repeat twice. At this time, release the TV and wait until it’s lit continuously.

3.  Locate the code for your TV in Setup Codes for TVs below. Brands are listed in alphabetical order with the most popular codes listed first.

4. Enter the first four-digit code for your TV. If you perform this procedure correctly, the TV light will blink three times.
   NOTE: If you enter an invalid code, the TV light will turn off. In that case, repeat steps 2 through 4 with a valid code.

5.  Aim the DRC at your TV and press POWER once. The TV should turn off. If it does not respond, repeat steps 2-4, trying each code listed for your brand until you find the one that operates your TV. If your TV still does not work with the DRC, try searching for the code (see Searching For Your Code on the backside).

6. Write your TV code in the boxes below for future reference.

NOTE: Remember, to use the DRC to operate your TV, press TV first.

0016, 0039, 0166, 0466
Daewoo…………………………………………………………………………………………………………………. 0451, 0451, 0019, 0039, 0091, 0092, 0623,
Denon| 624
Dumont| 19
Dwain| 145
Dynatech| 0017, 0019
Electro band| 0720, 0774
Electrohome| 49
Emerson| 0154, 0236, 0463, 0180, 0282, 0178, 0019, 0179, 0039, 0038, 0158, 0177, 0181, 0182, 0183, 0185, 0270, 0280,  0623, 0624
---|---
Envision| 0030
Fisher| 0154, 0159
Fujitsu| 0179
Funai| 0180, 0179, 0171
Futuretech| 0180
GE| 0047, 0051, 0451, 0093, 0282, 0178,0021, 0055, 0027, 0029, 0135, 0174, 0251, 0279
Gibraltar| 0017, 0030, 0019
GoldStar| 0030, 0178, 0019, 0056, 0001, 0002,
Gradiente| 0053, 0056, 0392
Grumpy| 0180, 0179
Hallmark| 0178
Harley| 0179
Hitachi| 0054, 0078
Infinity| 0180, 0068
Inteq| 0145, 0056, 0032, 0038, 0097, 0151,
JBL| 0054
JCB| 0017
JVC| 0054
Janeil| 0000
KEC| 0053, 0036, 0069, 0160, 0169, 0182
KMC| 0046
KTV| 0180
Kamp| 0106
Kawasho| 0180, 0030, 0039, 0183, 0185, 0217,
Kaylani| 0216
Kenwood| 0158, 0216, 0308
Kloss 0024, LG| 0052
LXI| 0030, 0019
Logik| s 0024, 0046, 0078
Luxman| 0056
MEI| 0047, 0054, 0154, 0156, 0178, 0148
MGA| 0016
MTC| 0056
Magnavox| 0185 0036, 0096, 0186, 0187, 0230, 0386
Majestic| 0150, 0030, 0178, 0019, 0155
Marantz| 0060, 0030, 0019, 0056, 0049, 0091,
Matsushita| 0036, 0096, 0186, 0187, 0230, 0386
Megatron| 0016, 0015
Memorex| 0054, 0030 0106
Midland| 0250
Minute| 0178, 0145, 0003
Mitsubishi| 0154, 0250, 0150, 0178, 0056, 0016,
Motorola| 0047, 0017, 0051, 0039, 0032, 0135 0155, 0331, 0358
Multitech| 0021
NAD| 0093, 0150, 0178, 0019, 0014, 0098,
NEW| 0093, 0055
NTC| 0180, 0049, 0217
Nikko| 0156, 0178, 0166
Noblex| 0030, 0019, 0056, 0036, 0497
Noshi| 0092
Onwa| 0030, 0178, 0092
Optimus| 00430
Optonica| 0018
Orion| 0180
Panasonic| 0154, 0250, 0166
Penney| 0093, 01650021, 0019, 0018, 0056, 0039, 0002, 0003, 0027, 0032, 0110, 0135
Philco| 0236, 0463, 0179
Philips| 0051, 0250, 0055, 0162, 0226
Pilot| 0047, 0156, 0051, 0060, 0030, 0178,
Pioneer| 0028, 0096
Portland| 0054
Prism| 0030, 0019, 0039
Proscan| 0038, 0166
Proton| 0019, 0039, 0092
Pulsar| 0051
Quasar| 0047
RCA| 0178, 0003, 0031, 0052, 0466
Harley| 0017, 0019
Davidson Harman| 0051, 0250, 0165, 0055, 0219
Kardon Harvard| 0047, 0051, 0093, 0019, 0018, 0029,0038, 0090, 0135, 0174, 0278
Radio Shack| 0047, 0154, 0165, 0180, 0030, 0178,0019, 0056, 0039, 0032, 0409
---|---
Realistic| 0056, 0039, 0032 0019, 0056, 0039, 0032, 0409
Rhapsody| 0183, 0185, 0216
Runco| 0017, 0030, 0251, 0497, 0603
SSS| 0180, 0019
Sampo| 0030, 0039, 0032, 0052, 0110
Samsung| 0060, 0030, 0178, 0019, 0056, 0032,0329, 0427, 0482
Sansei| 0039
Sansui| 0451
Sanyo| 0463
Scimitsu| 0154, 0146, 0159, 0484
Scotch| 0019
Scott| 0178
Sears| 0236, 0180, 0178, 0019, 0179 0056, 0015, 0146, 0148, 0159, 0168, 0171, 0281
Semivox| 0047, 0054, 0154, 0156, 0178, 0179,
Sep| 0156
Sharp| 0093, 0165, 0039, 0153, 0157, 0281,0386, 0491
Shogun| 0019
Signature| 0016
Simpson| 0186, 0187
Sony| 0000, 0011, 0080, 0111
Soundesign| 0180, 0178, 0179, 0186
Spectron| 0003, 0137
Square view|

0171 ,0015, 0146, 0148, 0159

Starlite| 0080
Supre-Macy| 0046
Supreme| 0000
Sylvania| 0054, 0030, 0020, 0028, 0065, 0096,0381
Symphonic| 0171
TMK| 0178, 0056, 0177
Tandy| 0093
Tatung| 0055, 0003, 0049, 0396
Technics| 0051, 0250
Technol Ace| 0179
Technovox| 0007
Techwood| 0051, 0056, 0003
Teknika| 0054, 0180, 0150, 0060, 0019, 0179,0056, 0016, 0039, 0092, 0186, 0312
Telefunken| 0056
Tera| 0031
Toshiba| 0154, 0156, 0060, 0036
Tonic| 00185
Television| 0039
Trial| 00157
Universal| 0027
Vector Research Victor| 0030
Video Concepts Vidikron| 0053
Vtech| 0098
Viking| 0054, 0242
Wards| 0178, 0019, 0036 ,0179, 0056, 0016, 0020, 0027, 0028,
0029, 0080, 0096, 0111, 0174
White Westinghouse Yamaha| 0046, 0312
Zenith| 0054, 0165, 0030, 0178, 0021, 0019,
Zonda| 0623, 0624
Yamaha| 0030, 0019
Zenith| 0017, 0016, 0092
Zonda| 0003

PROGRAMMING VCR CONTROL

1. Turn on your VCR and insert a videocassette.

2. On the DRC, press and hold VCR (at least 6 seconds) until you see the programming mode start. Each of the mode key lights will turn off and on sequentially, starting with AUX on through TV, and the sequence will repeat twice. During this time, release VCR and wait until it’s lit continuously.

3.  Locate your VCR brand in the SETUP CODES FOR VCRs below. Brands are listed in alphabetical order with the most popular codes listed first.

4. Enter the first four-digit VCR code for your VCR. If you perform this procedure correctly, the VCR light will blink three times.
   NOTE: If you enter an invalid code, the VCR light will turn off. In that case, repeat steps 2 through 4 with a valid code.

5. Aim the DRC at your TV and press POWER once. Your VCR should turn off. If your VCR remote control does not have a POWER key, press PLAY. If it does not respond, repeat steps 2-4, trying each code listed for your brand until you find the one that operates your VCR. If your VCR still does not work with the DRC, try searching for the code (see Searching For Your Code on the backside).

6. Write your VCR code in the boxes below for future reference.

NOTE: Remember, to use the DRC to operate your VCR, press VCR first.

Set up Codes for VCR

0208, 0211, 0212, 0294, 0295, 0361, 0479, 0510, 0561
Fuji| 0047, 0104, 0054, 0066
Funai| 0035, 0033
GE| 0000
Garrard| 0060, 0035, 0048, 0240, 0065, 0202
Go Video| 0000
GoldStar| 0232, 0279, 0350, 0432, 0526
Gradiente| 0037, 0038, 0018, 0471, 0480
Grundig| 0000, 0008, 0408
HI-Q –| 0047
---|---
Harley Davidson| 00000
Harman/Kardon| 0081,0038,0075
Harwood| 0072,0068
Headquarter| 00046
Hitachi| 0000,0042,0041,0065,0082,0105, 0166,0292,0396
WC| 0067,0041,0008,0206,0207,0384′
I Jensen| 00041
KEC| 0037,0278
KLH| 00072
Kemvood| 0067t 0041t 0038r 0384
Kodak| 0035,0037
LXI| 00037
Lloyd’s| 0000,0208
Logik| 00072
MEI| 00035
MGA ‘| 0290,0043,13061
MGN Technology| 00240
MTC| 0290,0006
Magnasonic| 00278
Magnavox| 0035,0039,0081, 0000,0149,010 i, 0110
Magnin| 00240
Marantz| 4.’0035,0081
Marta| 0037
Matsushita| 0035.0162,0454
Memorex| 0035,0037, 0048, 0039,0047, 0290,4 0000,0104,0162, 0046,0299,0307
Minolta| 0042,0105
Mitsubishi| 0048,0067,0043,0061,0075,0173, 0219,0292,0443
Motorola| 0035,0048
Multitech| 0000,0072
N AD| 000584
NEC| 0104,0067,0041, 0038,0040,0050, 0082
Nikko| 0037
Nikon| 0034,0253
Noble:| 000290
%Olympus| 0035.0226
Optimus| 0037,0048,0104, 0162,0058,0432, 0454
Optomo| 0062
Orion| 0184.0002.0295, 0479  0035,0162,0077,
0102, 022p, 0226, 0227,0246,0378, 0454
Panasonic
Penney| 0035,0037,0240,0042,0038,0040, 0054
Pentax| 0092,0065,0105
Philco| 0035,0209,0479
Philips| 0035,0081,0062,0110,0403
Pilot| 0037
Pioneer| 0067,0058, (9168
Portland| 0230
Protnromc| 0240
Proscan| 0060,0202
Protec| 0072
Pulsar| 0039,0051
Quarter| 0016
Quartz| 0046, 0155
Quasar| 0035,0162,0077,0454
0060,0035,0048,0240,0042,0149,
0065,0077,0105,0106,0202,0277
RCA
Radio Shack| 00000
_Radix| 000037— 4
Randex| 0037
Realistic| 0035,0037,0048,0047,0000,0104, 0062,0046,0066
Ricoh| 0039,0253
Runco| 0039
SI S| 0042
Salon| 0075
Samsung| 0240, 0015, 0051, 0053
Sank’| 480039
Sansui| 0000,0067.0041.0082,0271,0479
Sanyo| 0047,0290,0104, 0096
Scott| 0189,0095,0121, 0043,0210,0211, 0212
Sears| 0035,0037,0047, 0000,0042,0104,  0046,0054,0057, 0066, 0105
Semp| 0045
Sharp| 0048,0062
Shmtom| 0072
Shogun| 0290,0051
Singer| 0072

PROGRAMMING VCR CONTROL

Setup Codes for VCRs (continued):

Setup Codes for TV/VCR Combos:

NOTE: Some TV/VCR Combo codes may require a separate TV code to control volume. Check the codes above and follow the instructions in the “Programming TV  ontrol” section (on the front side) using the supplied TV code. If there is no TV code listed for your TV/VCR Combo’s operating code, you will need to use the volume control capabilities of your General Instrument Cable Converter.

PROGRAMMING CABLE CONVERTER (OR DBS) CONTROL

When you received your DRC remote control, it was already programmed to operate your GI Cable Converter. However, if you want to control a DBS receiver or a different Cable Converter, perform the following instructions (otherwise skip to the next topic):

1. Turn on the Cable Converter or DBS Receiver.

2. On the DRC, press and hold CABLE (at least 6 seconds) until you see the programming mode start. Each of the mode key lights will turn off and on sequentially, starting with AUX on through TV, and the sequence will repeat twice. During this time, release CABLE and wait until it’s lit continuously.

3. Locate your Cable Converter or DBS brand in the SETUP CODES FOR CABLE CONVERTERs or SETUP CODES FOR DBSs below. Brands are listed in alphabetical order with the most popular codes listed first.

4. Enter the first four-digit code for your Cable Converter or DBS. If you perform this procedure correctly, the CABLE light will blink three times.
   NOTE: If you enter an invalid code, the CABLE light will turn off. Repeat steps 2 through 4 with a valid code.

5. Aim the DRC at your Cable Converter or DBS Receiver and press POWER once. Your Cable Converter or DBS receiver should turn off. If it does not respond, repeat steps 2-4, trying each code listed for your brand until you find the one that operates your Cable Converter or DBS Receiver. If your unit still does not work with the DRC, try searching for the code (see Searching For Your Code).

6. Write down the Cable Converter or DBS Receiver code in the boxes below for future reference.”
   NOTE: Remember, to use your DRC to operate your Cable Converter or DBS Receiver, press CABLE first.

SETUP  CODES FOR CABLE CONVERTERS

SETUP  CODES FOR DBS RECEIVERS

PROGRAMMING AUXILIARY COMPONENT CONTROL

To program the DRC to control an auxiliary component (e.g., a second TV or VCR, a GI DBS Receiver, or Digital Audio Tuner):

1. Turn on your auxiliary component (and if it’s a VCR, insert a video cassette).

2. On the DRC, press and hold AUX (at least 6 seconds) until you see the programming mode start. Each of the mode key lights will turn off and on sequentially, starting with AUX on through TV, and the sequence will repeat twice. During this time, release AUX and wait until it’s lit continuously.

3. Locate the brand in the SETUP CODES listed for your type of auxiliary unit  (e.g., VCRs, TVs, Cable Controllers, or DBS Receivers) or audio service listed below. Brands
   are listed in alphabetical order with the most popular codes listed first.

4. Press AUX, VCR, CABLE, or TV once to let the DRC know what type of device you want to assign to the AUX mode.

5. Enter the first four-digit code for your auxiliary component. If you perform this procedure correctly, the AUX light will blink three times.
   NOTE: If you enter an invalid code, the AUX light will turn off. In that case, repeat steps 2 through 5 with a valid code.

6. Aim the DRC at your auxiliary component and press POWER once (or PLAY once if it’s a VCR). The device should turn off (or start playing the tape). If the auxiliary component does not respond, repeat steps 2-6, trying each code listed for your brand until you find the one that operates your auxiliary component. If it still does not work with the DRC, try searching for the code (see Searching For Your Code).

7. Write down the auxiliary component type and its code in the spaces below for future reference.
   TYPE: __ NOTE: Remember, to use the DRC to operate your auxiliary component, press AUX first.

DRC Setup Codes for Miscellaneous
Audio Services:

SEARCHING FOR YOUR CODE

If your TV, VCR, Cable Converter or Auxiliary Component does not respond to the DRC after trying all of the codes listed for your brand, or if your brand is not listed at all, try searching for your code. For example, after trying all of the codes for your TV, you still cannot get the DRC to operate your TV, then:

1. Turn on your TV.

2. On the DRC, press and hold a TV (at least 6 seconds) until you see the programming mode start. Each of the mode key lights will turn off and on sequentially, starting with AUX on through TV, and the sequence will repeat twice. During this time, release the TV and wait until it’s lit continuously.

3. Press the (UP) cursor key once to start the search mode.
   NOTE: In the search mode, the DRC will send IR codes from its library to the selected component, starting with the most popular codes first. When the component responds to a subsequent key command (e.g., POWER), the correct device code will be found.

4. Press POWER once. The TV key will light on and off, showing that an IR code has been sent.

5. If your television does not turn off, press the UP cursor key once again to call up the next IR code and press POWER once again.

6. If your television still does not turn off, repeat step 5 as many times as needed until your TV turns off.

7. When your television does turn off, a working code has been found. Press OK once to save the code and the TV key will blink three times, confirming the selection.

8. To search for the codes of your other components, repeat steps 1 through 7, but substitute the appropriate device key (i.e., VCR, CABLE, or AUX) for the component you are searching for.

CHECKING THE CODES

If you have set up the DRC using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment. Perform the following procedure after you have set up your components to find out which four-digit code is operating your equipment.
For example, to find out which code is operating your TV:

1. Turn on your TV.

2.  On the DRC, press and hold the TV (at least 6 seconds) until you see the mode light sequence start. Each of the mode key lights will turn off and on sequentially, starting with AUX on through TV, and will repeat twice. During the sequence, release the TV key and wait until it stays lit continually.

3.  Press 9 – 9 – 0. The TV key will blink three times.

4. To view the code for the first digit, press and release 1. Count the number of TV key blinks (e.g., 3 blinks = 3) and write down the number in the leftmost box below.
   NOTE: The mode key will not blink if the code digit is a “0”.

5. Repeat step 4 three more times for each successive digit by pressing and releasing 2, 3, and then 4. Finish writing down the code in the boxes above.

6. To check for the codes of your other components, repeat steps 1 through 5, only substitute the appropriate device key (i.e., VCR, CABLE, or AUX) for the component you are checking. Write down the codes in the boxes below.

VCR

CABLE
AUX

CHANGING VOLUME LOCK

Your new DRC is set to control the volume of a component through its associated mode (i.e., through the cable in the Cable mode, through the TV in the TV mode, and through the auxiliary device in the Aux. mode). If your TV is not remote controllable, or if you would like the volume to be controlled by a different component, you can change the Volume Lock setting to control a volume through a non-associated mode (e.g., through the cable in the TV mode).
Changing the Volume Lock setting to the Cable or TV mode will change the volume control for all modes except Aux., which will continue to control its own volume. If you change the Volume Lock setting to the Aux. mode, all modes (i.e., Aux., Cable, and TV) will be controlled by the Aux. mode.
NOTE: The volume controls will not operate if Volume Lock is set to VCR mode.
To change the Volume Lock setting to the TV mode:

1. On the DRC, press and hold the TV (at least 6 seconds) until you see the programming mode start. Each of the mode key lights will turn off and on sequentially, starting with AUX on through TV, and the sequence will repeat twice. During this time, release the TV and wait until it’s lit continuously.
2. Press and release VOLUME +.
3. . The TV key light will blink three times, indicating the volume has been locked to the TV mode.
4. Now, whenever you press VOLUME +, VOLUME -, or MUTE on the DRC, the volume will be controlled by your TV.

To change the Volume Lock setting to the CABLE mode:

1. On the DRC, press and hold CABLE (at least 6 seconds) until you see the programming mode start. Each of the mode key lights will turn off and on sequentially, starting with AUX on through TV, and the sequence will repeat twice. During this time, release CABLE and wait until it’s lit continuously.
2. Press and release VOLUME +.
3. The CABLE key light will blink three times, indicating the volume has been locked to the CABLE mode.
4. Now, whenever you press VOLUME +, VOLUME -, or MUTE on the DRC, the volume will be controlled by your Cable Converter.

To change the Volume Lock setting to the AUX mode:

1. On the DRC, press and hold AUX (at least 6 seconds) until you see the programming mode start. Each of the mode key lights will turn off and on sequentially, starting with AUX on through TV, and the sequence will repeat twice. During this time, release AUX and wait until it’s lit continuously.
2. Press and release VOLUME +.
3. The AUX key light will blink three times, indicating the volume has been locked to the AUX mode.
4. Now, whenever you press VOLUME +, VOLUME -, or MUTE on the DRC, the volume will be controlled by your Auxiliary Device.

To unlock Volume Lock:

1. On the DRC, press and hold a mode key (at least 6 seconds) until you see the programming mode start. Each mode key light will turn off and on sequentially, starting with AUX on through TV, and the sequence will repeat twice. During this time, release the mode key and wait until it’s lit continuously.
2. Press and release VOLUME -.
3. The mode key light will blink three times, indicating volume has been unlocked for the selected mode.
4. Now, whenever you press VOLUME +, VOLUME -, or MUTE on the DRC, the volume controls will reset to their original device.

TROUBLESHOOTING

component does not respond.
SOLUTION:| Make sure the DRC is aimed at your home entertainment component and is no farther than
15 feet away.
PROBLEM:| DRC does not control
home entertainment components or commands are not working properly.
SOLUTION:| ‘fry all listed codes for the component brands being set up. Make sure they can be operated with infrared remote control.
PROBLEM:| TV/VCR combo does not respond properly.
---|---
| Use the VCR codes for your brand. Some combo units may require both a TV code and a VCR code for full operation.
SOLUTION:
PROBLEM:
SOLUTION:| No volume on a 2nd TV. I Follow instructions in Changing Volume Lock.
PROBLEM:| CHANNEL+, CHANNEL-, and LAST do not work for your RCA TV.
SOLUTION:| Due to the RCA design (19831987), only the original remote control will operate these functions.
PROBLEM:| Changing channels does not work properly.
SOLUTION:| If the original remote control required pressing ENTER to change channels, press ENTER on the DRC after entering the channel number.

ADDITIONAL INFORMATION

The GI DRC does not have any user-serviceable parts. Opening the case, except for the battery cover, may cause permanent damage to your GI remote control. Copyright 1999 by General Instrument, Inc. No part of this publication may be reproduced, transmitted, transcribed, stored in any retrieval system, or translated to any language, in any form or by any means, electronic, mechanical, magnetic, optical, manual, or otherwise, without the prior written permission of General Instrument, Inc.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>