Mediakind S16955-M1-1RU Interface Module User Guide

Mediakind S16955-M1-1RU Interface Module

Quick Start Guide

Step 1: Connections/Power

1. Insert the 2 CAMs into the required slots in the common interface module of the unit .
   CAUTION : The CAMs are labeled with the matching serial number of the unit, DO NOT mix CAMs between units.

2. Quad Satellite input: connect the F-Type cable(s) to the rear of the unit :
   • Input 1: Feed for G15 (Vertical)
   • Input 2: Feed for G17 (Vertical)
   • Input 3: Feed for G15 (Horizontal)
   • Input 4: Feed for G17 (Horizontal)

3. ASI output: connect the ASI cable to the rear of the unit, on port 2 .

4. Management: connect the Ethernet cable to the rear of the unit on eth0 .

5. Quad 1 GbE output: connect the Ethernet cable(s) to the rear of the unit, (by default, eth2) .

6. Connect the power cord to the back of the unit . Plug the power cord into the grounded outlet, then power up the unit.

Step 2: Configure the network interfaces

The Ethernet interfaces can be configured using the LCD panel:

1. From the root menu, navigate to Network by pressing.
2. Select Eth0 by pressing. Press  again to get to the parameters.
3. For Method, press ENTER, and the  arrows to select Manual. Press ENTER.
4. Press select IP Address. Press ENTER, then  and to enter the address for the management network. Press ENTER to apply the value.
5. Press select Subnet Mask. Press ENTER, then and to enter the mask for the management network. Press ENTER to apply the value.
6. Press select Gateway. If using a gateway, press ENTER, then and to enter the gateway. Press ENTER to apply the value.
7. Press and then twice to select Eth2. Adjust the IP Address and Subnet Mask in the same way as you edited Eth0.
8. For installations using IP outputs edit the address and mask according to the network plan.
9. For installations using an SD transcoder and an Ethernet cable direct to it, use the IP Address 192.128.2.1 and Subnet Mask 255.255.255.0.
10. Do not edit Eth2 Gateway.

Step 3: Login

Launch a web browser:
HTTP://{IP-Address} where {IP-Address} is that set in Step 2.

Enter the username FoxReceivers and password Change2YourSite.

Step 4: Get the receiver entitled

1. Record the receiver serial number starting with 4E as printed on the back of the unit.
2. Call Fox on 1-888-882-5295.

Step 5a: Check the entitled services and adjust

1. Choose Services.

Step 5b: Check the entitled services and adjust

Go to the Solution Manager Transcode and click on the Edit icon.

Check that the Services you think need to be entitled, are entitled, once the Fox representative informs you that the receiver is now entitled. The default Codec for the transcoded service output is MPEG-2 Main. If you need H.264 (AVC), click on the Cog icon on the service you need to adjust, and select H.264 Main.

Press Save and Continue.

Step 6: Configure the output MPTS

1. Click on the Output tab.
2. Enter the output multicast details:
   • Total Bitrate must be enough for all services and overhead of PSI/SI tables, etc.
   • Stream Address is the multicast or unicast address. Multicast ranges are from 224.0.0.0 to 239.255.255.255.
   • Destination UDP port is in the range 0 to 65353, although ports 0 to 1023 should be treated as reserved as ‘well known ports’.
3. Press Save and Exit or Save and Continue to have these settings applied.

Step 7: Change Password

For improved security you may wish to change the password of the FoxReceivers user.
NOTE : You cannot change the username, nor add users.

1. On any page, on the top right corner, click on the username FoxReceivers.
2. Select Change password.
3. Enter the old password then enter the new password twice.

4. Click Change password.
   RX1 MPTS output

    | Service| PIDs|
   Service Name| Service ID| PMT| Video/PCR| Audio 1| Audio 2| SCTE- 35| Resolution
    | 21| 100| 101| 102| 103| 107| HD
    | 31| 120| 121| 122| 123| 127| SD
    | 22| 200| 201| 202| 203| 207| HD
    | 32| 220| 221| 222| 223| 227| SD
    | 23| 300| 301| 302| 303| 307| HD
    | 24| 400| 401| 402| 403| 407| HD
    | 25| 500| 501| 502| 503| 507| HD
    | 26| 600| 601| 602| 603| 607| HD

RX1 back Panel

1. Dual Common Interface
2. Quad Satellite input
3. ASI output
4. 1 GbE – eth0 for management
5. Quad 1 GbE output – eth2 for multicast
6. Power input

NOTE : The back panel components are SELV (Safety Extra Low Voltage) components.
CAUTION : CAMs supplied with the RX1 must be kept with the unit they were supplied with. Do not swap CAMs between RX1 units. The CAMs are labeled with the serial number of the RX1 they belong with. To keep the CAMs with the RX1, we recommend plugging the CAMs into the CI slots soon after unboxing the RX1. Where two CAMs are supplied, it does not matter which CI slot each CAM is fitted in. Always unplug CAMs from the RX1 unit when it transported. Leaving a CAM in a CI slot risks damage to the CAM or the RX1 CI slots.

An electronic copy of this document is available for download at:
https://www.mediakind.com/rx1-quick-start-guide

Documents / Resources

| Mediakind S16955-M1-1RU Interface Module [pdf] User Guide
S16955-M1-1RU Interface Module, S16955-M1-1RU, Interface Module
---|---
| MediaKind S16955-M1-1RU Interface Module [pdf] User Guide
S16955-M1-1RU, Interface Module, S16955-M1-1RU Interface Module

References

• RX1 Quick Start Guide - MediaKind

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>