PANTUM CDW-G4822BU-01 WiFi Module User Manual
- June 6, 2024
- Pantum
Table of Contents
- PANTUM CDW-G4822BU-01 WiFi Module
- Overview
- Features
- Precautions
- FCC regulatory compliance statement
- Frequency Band
- General Specification
- DC Characteristics
- Dimension & Pin Assignments
- Key material list
- Modular photo
- Electrical Characteristics
- Packing information
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
PANTUM CDW-G4822BU-01 WiFi Module
Overview
The CDW-G4822BU-01 is based on RTL8822BU-CG, which supports 2-stream 802.11ac solutions with multi-user MIMO (Multiple-Input, Multiple-Output) with Wireless LAN (WLAN) USB2.0 network interface controller. It combines a WLAN MAC, a 2T2R capable WLAN baseband, and RF in s single chip. The CDW-G4822BU-01 provides a complete solution for high-performance integrated wireless.
Features
- IEEE 802.11a/b/g/n/ac compatible WLAN
- 5MHz / 10MHz / 20MHz / 40MHz / 80MHz bandwidth transmission
- Complies with USB2.0 for WLAN controller
- Dual-band 2T2R mode with data rate up to 867Mbps
- Support 802.11ac 2×2, Wave-2 compliant with MU-MIMO
- Complete 802.11n MIMO solution for 2.4GHz and 5Ghz band
- Maximum PHY data rate up to 173.3 Mbps using 20MHz bandwidth,
- 400Mbps using 40MHz bandwidth, and 866.7Mbps using 80MHz bandwidth
- DSSS with DBPSK and DQPSK, CCK modulation with a long and short preamble, OFDM with BPSK, QPSK, 16QAM,64QAM and 256QAM modulation. Convolutional Coding Rate: 1/2, 2/3, 3/4,and 5/6
- Support STBC, Support LDPC
- Build-in both 2.4GHz and 5GHz PA, Build-in both 2.4GHz and 5GHz LNA
- Enhanced WLAN Coexistence Control to improve transmission quality in different profiles
Precautions
Pantum Regulatory Type/Model Number CDW-G4822BU-01; FCC ID:2AEGO4020WM 5G band I (5150-5350MHz) indoor use only. 5. Hereby, [Zhuhai Pantum Electronics Co., Ltd.] declares that the radio equipment type [CDW-G4822BU-01] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.http:WWW.PANTUM.COM
FCC regulatory compliance statement
Statement This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. §15.21 Information
to user
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
List of applicable FCC rules:
- 47 CFR Part 15, Subpart C 15.203
- 47 CFR Part 15, Subpart C 15.205
- 47 CFR Part 15, Subpart C 15.207
- 47 CFR Part 15, Subpart C 15.209
- 47 CFR Part 15, Subpart C 15.247
- 47 CFR Part 15, Subpart E 15.407
Summarize the specific operational use conditions
This module can be used in IoT devices, the input voltage to the module is
nominally 5V. Only the embedded integral antenna is allowed. Any other
external antenna is prohibited.
Limited module procedures
This module is not a limited module.
Trace antenna designs
The antenna is not a trace antenna.
RF exposure considerations
This Module complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Antennas
If you desire to increase antenna gain and either change antenna type or use
the same antenna type certified, a
Class II permissive change application is required to be filed by us, or you
(host manufacturer) can take responsibility through the change in FCC ID (new
application) procedure followed by a Class II permissive change application.
Label and compliance information
Please notice that if the FCC identification number is not visible when the
module is installed inside another device, then the outside of the device into
which the module is installed must also display a label referring to the
enclosed module. following: “Contains FCC ID: 2AEGO4020WM” any similar wording
that expresses the same meaning may be used. § 15.19 Labelling requirements
shall comply on end-user device.
Labeling rules for a special device, please refer to §2.925, § 15.19 (a)(5),
and relevant KDB publications. For E-label, please refer to §2.935.
Information on test modes and additional testing requirements
The OEM integrator is responsible for ensuring that the end-user has no manual
instruction to remove or install-module. The module is limited to installation
in mobile applications, a separate approval is required for all other
operating configurations, including portable configurations with respect to
§2.1093 and different antenna configurations.
Additional testing, Part 15 Subpart B disclaimer
This modular transmitter is only FCC authorized for the specific rule parts
listed on our grant, host product manufacturer is responsible for compliance
to any other FCC rules that apply to the host not covered by the modular
transmitter grant of certification. The host manufacturer in any case shall
ensure host product that is installed and operating with the module is in
compliance with Part 15B requirements. Please note that For a Class B or Class
A digital device or peripheral, the instructions furnished in the user manual
of the end-user product shall include the statement set out in. §15.105
Information to the user or such a similar statement and place it in a
prominent location in the text of host product manual. Original texts as
follows: For Class B
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Frequency Band
Frequency Band:
WiFi 2.4GHz:| 2412MHz – 2462MHz
WiFi 5GHz:| 5180MHz – 5320MHz, 5500MHz – 5700MHz
WiFi 5.8GHz:| 5745MHz – 5825MHz
maximum output power : (Declaration for EU Compliance)
Radio| Frequency| Output Power
WLAN 2.4GHz| 2412-2462MHz| 18.58 dBm EIRP
WLAN 5GHz
| 5180-5320MHz
5500-5700MHz
| 20.48 dBm EIRP
21.73 dBm EIRP
WLAN 5.8GHz| 5745-5825MHz| 13.58 dBm EIRP
General Specification
| Model | CDW-G4822BU-01 |
|---|---|
| Product Name | WIFi 11a/b/g/n/ac 2T2R |
| Major Chipset | Realtek RTL8822BU-CG |
| Standard | IEEE 802.11a/b/g/n/ac |
| Data Transfer Rate | 1,2,5.5,6,11,12,18,22,24,30,36,48,54,60, 90,120 and |
maximum of 867Mbps
Modulation Method| CCK//DBPSK/DQPSK/QPSK/16-QAM/ 64-QAM/256QAM
Frequency Band| 2412MHz – 2462MHz,5180MHz – 5320MHz, 5500MHz -5700MHz,5745MHz
– 5825MHz
Spread Spectrum
| IEEE 802.11b: DSSS (Direct Sequence Spread Spectrum)
IEEE802.11a/g/n/ac: OFDM (Orthogonal rthogonal Frequency Division Multiplexing)
Operation Mode| Ad hoc, Infrastructure
Antenna gain
| 2 dBi
Security| WEP, TKIP, AES, WPA, WPA2
Interface| USB 2.0
Operating Temperature| -20~ +70° C ambient temperature
Storage Temperature| -40 ~ 85°C ambient temperature
Humidity| 5 to 90 % maximum (non-condensing)
Dimension| 46.5x40x7.6mm (LxWxH)±0.2mm
DC Characteristics
| Symbol | Parameter | Min. | Typ. | Max | Units |
|---|---|---|---|---|---|
| VD33 | 3.3V I/O supply Voltage | 3.0 | 3.3 | 3.6 | V |
| VD10 | 1.05V Core Supply Voltage | 0.945 | 1.05 | 1.155 | V |
| VIH | Input high Voltage | 2.0 | 3.3 | 3.6 | V |
| VIL | Input low Voltage | — | 0 | 0.9 | V |
| VOH | output high Voltage | 2.97 | — | 3.3 | V |
| VOL | output low Voltage | 0 | — | 0.33 | V |
Dimension & Pin Assignments
| NO | Name | Type | Description |
|---|---|---|---|
| 1 | UV+ | – | Power supply 5V is required（MAX 5.5V） |
| 2 | USB_DM | I/O | USB data- |
| 3 | USB_DP | I/O | USB data+ |
| 4 | GND | – | Ground connections |
| 5 | BT_REG_ON | I | GPIO Control BT device enabled |
| 6 | ON/OFF | I | Control “EN” of DC-DC,High level (default) |
Key material list
| Type | P/N | supplier |
|---|---|---|
| Crystal | 40Mhz | JWT ，FK , SFJ |
| WIFI IC | RTL8822BU | RTL |
| PCBA VER | 63822BU G4822BU | A,O,S |
JWT 40MHz 3225 封装 FK 40MHz 3225 封装 SFJ 40MHz 3225 封装
Modular photo
Electrical Characteristics
GHz RF Specification
| Feature | Description |
|---|---|
| WLAN Standard | IEEE 802.11a/b/g/n/ac WiFi compliant |
| Frequency Range | 2.400 GHz ~ 2.497GHz (2.4 GHz ISM Band) |
| Number of Channels | CH1-CH11(America, |
Canda),CH1-CH13(Europe,China),CH1-CH14(Japan)
Modulation
| 802.11b : DQPSK, DBPSK, CCK
802.11 g/n : OFDM /64-QAM,16-QAM, QPSK, BPSK
Receive
Sensitivity (11b,20MHz) @8% PER
| – 1Mbps| PER @ -93 dBm, typical
– 2Mbps| PER @ -91 dBm, typical
– 5.5Mbps| PER @ -88 dBm, typical
– 11Mbps| PER @ -86 dBm, typical
Receive
Sensitivity (11g,20MHz) @10% PER
| – 6Mbps| PER @ -90 dBm, typical
– 9Mbps| PER @ -89 dBm, typical
– 12Mbps| PER @ -88 dBm, typical
| – 18Mbps| PER @ -85 dBm, typical
---|---|---
– 24Mbps| PER @ -82 dBm, typical
– 36Mbps| PER @ -79 dBm, typical
– 48Mbps| PER @ -74 dBm, typical
– 54Mbps| PER @ -72 dBm, typical
Receive
Sensitivity (11n,20MHz) @10% PER
| – MCS=0| PER @ -90 dBm, typical
– MCS=1| PER @ -87 dBm, typical
– MCS=2| PER @ -85 dBm, typical
– MCS=3| PER @ -81 dBm, typical
– MCS=4| PER @ -78 dBm, typical
– MCS=5| PER @ -73 dBm, typical
– MCS=6| PER @ -72 dBm, typical
– MCS=7| PER @ -70 dBm, typical
Receive
Sensitivity (11n,40MHz) @10% PER
| – MCS=0| PER @ -87 dBm, typical
– MCS=1| PER @ -84 dBm, typical
– MCS=2| PER @ -82 dBm, typical
– MCS=3| PER @ -79 dBm, typical
– MCS=4| PER @ -75 dBm, typical
– MCS=5| PER @ -71 dBm, typical
– MCS=6| PER @ -69 dBm, typical
– MCS=7| PER @ -68 dBm, typical
Maximum Input Level| 802.11b : -10 dBm
802.11g/n : -20 dBm
5GHz RF Specification
| Feature | Description |
|---|---|
| WLAN Standard | IEEE 802.11a/n/ac 2×2, WiFi compliant |
| Frequency Range | 5.15GHz ~ 5.35GHz 5.725GHz ~ 5.85GHz |
| Number of Channels | 5.0GHz：Please see the table |
Modulation
| 802.11a : OFDM /64-QAM,16-QAM, QPSK, BPSK
802.11n : OFDM /64-QAM,16-QAM, QPSK, BPSK
802.11ac : OFDM /256-QAM
| – 6Mbps PER @ -89 dBm, typical | |
|---|---|
| – 9Mbps PER @ -88 dBm, typical | |
| --- | --- |
– 12Mbps PER @ -87 dBm, typical
– 18Mbps PER @ -84 dBm, typical
– 24Mbps PER @ -81 dBm, typical
– 36Mbps PER @ -78 dBm, typical
– 48Mbps PER @ -73 dBm, typical
– 54Mbps PER @ -72 dBm, typical
Receive Sensitivity (11n,20MHz) @10% PER
| – MCS=0 PER @ -89 dBm, typical
– MCS=1 PER @ -86 dBm, typical
– MCS=2 PER @ -84 dBm, typical
– MCS=3 PER @ -81 dBm, typical
– MCS=4 PER @ -77 dBm, typical
– MCS=5 PER @ -72 dBm, typical
– MCS=6 PER @ -71 dBm, typical
– MCS=7 PER @ -68 dBm, typical
Receive Sensitivity (11n,40MHz) @10% PER
| – MCS=0 PER @ -86 dBm, typical
– MCS=1 PER @ -83 dBm, typical
– MCS=2 PER @ -81 dBm, typical
– MCS=3 PER @ -78 dBm, typical
– MCS=4 PER @ -74 dBm, typical
– MCS=5 PER @ -70 dBm, typical
– MCS=6 PER @ -68 dBm, typical
– MCS=7 PER @ -67 dBm, typical
Receive Sensitivity (11ac,20MHz) @10% PER
| – MCS=0, NSS1 PER @ -87 dBm, typical
– MCS=1, NSS1 PER @ -85 dBm, typical
– MCS=2, NSS1 PER @ -83 dBm, typical
– MCS=3, NSS1 PER @ -80 dBm, typical
– MCS=4, NSS1 PER @ -76 dBm, typical
– MCS=5, NSS1 PER @ -71 dBm, typical
– MCS=6, NSS1 PER @ -70 dBm, typical
– MCS=7, NSS1 PER @ -69 dBm, typical
– MCS=8, NSS1 PER @ -65 dBm, typical
| – MCS=0, NSS1 PER @ -85 dBm, typical
– MCS=1, NSS1 PER @ -82 dBm, typical
– MCS=2, NSS1 PER @ -80 dBm, typical
– MCS=3, NSS1 PER @ -77 dBm, typical
| – MCS=4, NSS1| PER @ -74 dBm, typical
---|---|---
– MCS=5, NSS1| PER @ -69 dBm, typical
– MCS=6, NSS1| PER @ -68 dBm, typical
– MCS=7, NSS1| PER @ -67 dBm, typical
– MCS=8, NSS1| PER @ -62 dBm, typical
– MCS=9, NSS1| PER @ -58 dBm, typical
Receive Sensitivity (11ac,80MHz) @10% PER
| – MCS=0, NSS1| PER @ -82 dBm, typical
– MCS=1, NSS1| PER @ -79 dBm, typical
– MCS=2, NSS1| PER @ -77 dBm, typical
– MCS=3, NSS1| PER @ -73 dBm, typical
– MCS=4, NSS1| PER @ -70 dBm, typical
– MCS=5, NSS1| PER @ -67 dBm, typical
– MCS=6, NSS1| PER @ -65 dBm, typical
– MCS=7, NSS1| PER @ -63 dBm, typical
– MCS=8, NSS1| PER @ -59 dBm, typical
– MCS=9, NSS1| PER @ -55 dBm, typical
Maximum Input Level| 802.11a/n/ac : -20 dBm
Packing information
ESD CAUTION
The CDW-G4822BU-01 is ESD (electrostatic discharge) sensitive device and may be damaged with ESD or spike voltage. Although CDW-G4822BU-01 is with built-in ESD protection circuitry, please handle with care to avoid the permanent malfunction or the performance degradation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>