Xvive U3C Microphone Wireless System Instruction Manual

U3C SET MANUAL
MICROPHONE
WIRELESS SYSTEM

**| CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN| **
---|---|---

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK: DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTSINSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THE APPLIANCE TO RAIN OR MOISTURE.

CERTIFICATION

Radio Approvals: FCC Part 15.249, FCC Part 15 B, RSS-210 (Canada), EN 300 440 (Europe), EN 301.489 (Europe), MIC Notice No.88 Appendix No.43(Japan)

This Class B digital apparatus complies with Canadian ICES-003.
IC Caution: RSS-Gen Issue 4 December 2014″&”CNR-Gen 4e Décembre 2014:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

FCC CERTIFICATION

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
WARNING:
Changes or modifications not expressly approved in writing by Xvive may void the user’s authority to operate this equipment.
RF EXPOSURE STATEMENT:
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
MEASURES:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT SAFETY INSTRUCTIONS PLEASE READ THESE INSTRUCTIONS

IN A SAFE PLACE

WARNING: BEFORE USING YOUR XVIVE U3C MICROPHONE WIRELESS SYSTEM, CAREFULLY READ THE OPERATING INSTRUCTIONS.

1. Observe all instructions carefully in the U3C set manual.

2. Do not to perform service operations beyond those described in the U3C set manual. Services required when the apparatus has been damaged in any way, such as:
   • Liquid has been spilled or objects have fallen into the apparatus
   • The unit has been exposed to rain or moisture
   • The unit does not operate normally or changes in performance in a significant way
   • The unit is dropped or the enclosure is damaged

3.  Do not place near heat sources, such as radiators, heat registers, or appliances that produce heat.

4. Guard against objects or liquids entering the device. Do not use or place unit near water.

5. Clean only with a dry cloth.

6. Only use attachments/accessories specified by the manufacturer.

7.  Prolonged listening at high volume levels may cause irreparable hearing loss and/or damage. Always be sure to practice “safe listening.”

U3C SET PRODUCT INTRODUCTION

• 2.4Ghz band is optimal for condenser microphone wireless system, Approved for use in worldwide.
• Less than 5ms Latency, Simultaneous broadcasts on 6 channels.
• Broad 20Hz – 20KHz frequency response
• Up to 90 feet (actual range depends on RF signal absorption, reflection and interference )
• 3-7 Hours of battery life (It depends on the microphone phantom power current. Rechargeable battery for both Transmitter & Receiver)
• Only work with XLR balanced condenser microphone.
• High-Resolution 24-bit/48kpbs Audio
• Dynamic Range 110dB
• Signal to Noise Ratio is 110dB
• U3C wireless aims to take the complexity and frustration, out of traditional wireless microphone systems. Creating a flexible, all-in-one solution that makes any your favorite condenser microphones into wireless.
• Provides 12V or 48V phantom power to the condenser microphone.
• Never plug single-ended (unbalanced) or dynamic microphones into U3C, can be permanently damaged if phantom power is applied to them.

QUICKSTART

1.  Plug the U3C Transmitter condenser microphone. Switching phantom power 12V or 48V
   WARNING : Never plug single-ended (unbalanced) or dynamic microphones into U3C

2. Plug the U3 Receiver into the Mixer.

3. Turn on the U3C Transmitter and Channel is the same.

4.  After connecting successfully, the LED lights on the U3 receiver will stay on.

5. Check the connection by taking through the microphone

BASIC OPERATION

U3C TRANSMITTER

1.  Mic In XLR balanced condenser microphone input jack
2. Spring: Circumferential ground spring providing an accurate connection to the mating shell
3. Mic Lock: secures transmitter to the microphone
4. Output phantom power voltage switching: 12V and 48V
5. Power switch: switches unit on/off
6. Channel status LED: indicates the selected channel
7. Channel switch: selects Channels 1-6
8. USB charging port
9. Power status LED: indicates power status: Led off = 100% — 30% Solid red = 29% — 11% Flickering red = less than 10%
10. Antenna.

BASIC OPERATION

U3 RECEIVER

1.  XLR OUT: XLR microphone input jack
2. Power switch: switches the unit on and off
3. Channel status LED: indicates the selected channel
4. Channel switch: selects Channels 1-6
5. USB Port: For charging the battery
6. RF Status LED: ON = Transmitter is on and link is established Flashing = Signal connection interference OFF = Transmitter off or unlinked
7. Power status Led: indicates power status. Led off = 100% — 30% Solid red = 29% — 11% Flickering red = less than 10%
8. Antenna.

SPECIFICATIONS

U3C MICROPHONE WIRELESS SYSTEM

Reflection And Interference.
Audio Frequency Response|  20Hz – 20KHz(-3dB). Dependent On Microphone Type Or Input Signal.
Dynamic Range| 110dB
Battery Life| Up To 3~7 Hours of battery life (It depends on the microphone current.
RF Sensitivity| -88dBm
Total Harmonic distortion| 0.2%
RF Output Power| 10 mW E.I.R.P. max
Operating Temperature Range| -18 to 57 . Battery Characteristics May Limit This Range.
Channel Count| Up To 6 Channels
| U3C TRANSMITTER| U3 RECEIVER
---|---|---
Dimensions| 31 X 29 X 98 mm| 31 X 29 X 98 mm
Weight| 108g| 92g
Housing| Molded Plastic And Cast Metal| Molded Plastic And Cast Metal
Battery| 3.7V Rechargeable Li-lon, 1000mA| 3.7V Rechargeable Li-lon, 860mA
Impedance| Input|  Output 4700(1 kHz)
Audio Input Connector| Balanced XLR Male Input|
Audio Output Connector| Balanced XLR Female Output
Maximum Input Level| 2.8Vp-p|
Maximum Output Level| 2.8Vp-p
Battery Life| phantom power:
12V 2mA – 7hours
48V 2mA – 6hours
48V 5mA – 3hours| Up To 5 Hours
Support Microphone Type                                    Condenser Microphones.|
Antenna Impedance| 50Ω| 50Ω
Antenna Type| 1/4 Wave Sleeve Dipole, Non-removable| 1/4 Wave Sleeve Dipole, Non-removable
Number Of Antennae| 1| 2

BATTERIES AND CHARGING

• LED lights up when you charge the U3C, and LED goes off automatically once charge is finsihed.
• Turn off the power switch while charging. Please do not use U3C when charging, which may reduce battery life.

U3C set

• Always store U3C at room temperature * When storing the unit, please check the battery state regularly and charge if necessary.

U3C Phantom Power Connections

2.4 GHz SPECTRUM OVERVIEW AND INTERFERENCE

U3C operates within the 2.4GHz ISM band which is utilized by Wi-Fi, Bluetooth, and other wireless devices. 2.4GHz is an open band and, as such, does not require a license to be used worldwide.
Tips and Methods to Improve Wireless System Performance

1. Keep more than 3 meteres distance between Receiver unit and other WiFi transmitters such as routers.
2. Change channels to avoid interference with other WiFi products.
3. In case of environmental interference from other WiFi systems, shorten the distance between the receiver and transmitter units.

2.4Ghz Frequency Tables

• U2 1~4 channels are the same as U3/U3C 1~4 channels, U2 and U3/U3C use in sametime max is 6 sets.

TROUBLESHOOTING

microphone is turned on and receiving signal from the U3C Transmitter. • Check that the power switch is turned on for both the Transmitter and the Receiver. • Ensure that the U3C Transmitter and Receiver are on the same channel. • U3C will provide 12V or 48V phantom power to condenser microphone. Please select your microphone phantom power volts. • If used in dynamic microphone, the current consumption will be the same as that of a condenser microphone. • The receiver can be paired with one Transmitter at a time.
Distortion or Faint Sound| • If you connect the device with a receiver, check if the device is balanced XLR interface
Signal instability: RF LED

flickering or off completely

| • See, “Tips and methods to improve wireless system performance” page 12
Unable to switch the channel| • The channel switch locks after 15 seconds. Double-click the channel button to unlock and reset.
Multiple connect| Use one transmitter can connect with more than 2 receivers.
Phantom Power| Never plug single-ended (unbalanced) or dynamic microphones into U3C,
can be permanently damaged if phantom power is applied to them.

APPLICATION SCENE

China Patent Numbers ZL 2016 3 0165464.8
2nd floor, Building 12, Xicheng Industrial Area, Xixiang Town,
Baoan District, Shenzhen Guangdong China. 518101
E-mail:[email protected]
www.xvive.com

Documents / Resources

| Xvive U3C Microphone Wireless System [pdf] Instruction Manual
U3C, Microphone Wireless System
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>