NINJA SS150 Series Twisti High-Speed Blender Duo Instruction Manual
- June 6, 2024
- Ninja
Table of Contents
TWIST ™
HIGH-SPEED BLENDER DUO
SS150 Series | Owner’s Guide
**IMPORTANT SAFETY INSTRUCTIONS
**
PLEASE READ CAREFULLY BEFORE USE • FOR HOUSEHOLD USE only
**| Read and review instructions for operation and use.
---|---
**| Indicates the presence of a hazard that can cause personal injury,
death or substantial property damage if
the warning included with this symbol is ignored.
| For indoor and household use only.
When using electrical appliances, basic safety precautions should always be followed, including the following:
WARNING
To reduce the risk of injury, fire, electrical shock or property damage,
basic safety precautions must always be followed, including the following
numbered earnings and subsequent instructions. Do not use appliances other
than intended use.
-
Read all instructions prior to using the appliance and its accessories.
-
Carefully observe and follow all warnings and instructions. This unit contains electrical connections and moving parts that potentially present risk to the user.
-
ALWAYS exercise care when handling the Hybrid Edge™ Blades Assembly. The blades are sharp, handle carefully. ONLY grasp the Hybrid Edge Blades Assembly by the outer perimeter of the blade assembly base. Failure to use care when handling the blade assembly will result in a risk of laceration.
-
Take your time and exercise care during unpacking and appliance setup. This appliance contains sharp, loose blades that can cause injury if mishandled.
-
Take inventory of all contents to ensure you have all parts needed to properly and safely operate your appliance.
-
Blades are sharp. Handle carefully.
-
Unplug the appliance from the outlet when not in use, before assembling or disassembling parts, and before cleaning. To unplug, grasp the plug by the body and pull from the outlet. NEVER unplug by grasping and pulling the flexible cord.
-
Before use, wash all parts that may contact food. Follow washing instructions covered in this instruction manual.
-
To protect against the risk of electric shock, DO NOT submerge the appliance or allow the power cord to contact any form of liquid.
-
DO NOT use this appliance outdoors. It is designed for indoor household use only.
-
This appliance has important markings on the plug blade. The attachment plug or entire cordset (if plug is molded onto cord) is not suitable for replacement. If damaged, the appliance shall be replaced.
-
This appliance has a polarized plug (one prong is wider than the other). To reduce the risk of electric shock, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT modify the plug in any way.
-
DO NOT operate any appliance with a damaged cord or plug, or after the appliance malfunctions or is dropped or damaged in any manner. This appliance has no user-serviceable parts. If damaged, contact SharkNinja for servicing.
-
Extension cords should NOT be used with this appliance.
-
DO NOT allow children to operate this appliance or use as a toy. Close supervision is necessary when any appliance is used near children.
-
This appliance is NOT intended to be used by people with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
-
Before each use, inspect blade assembly for damage. If a blade is bent or damage is suspected, contact SharkNinja to arrange for a replacement.
-
DO NOT attempt to sharpen blades.
-
DO NOT allow the unit or the cord to hang over the edges of tables or counters. The cord may become snagged and pull the appliance off the work surface.
-
DO NOT allow any part of the unit to contact hot surfaces, including stoves and other heating appliances.
-
ALWAYS use the appliance on a dry and level surface.
-
NEVER place a blade assembly on the motor base without it first being attached to the container.
-
Keep hands, hair, and clothing out of the container when loading and operating
-
ONLY use attachments and accessories that are provided with the product or are recommended by SharkNinja. The use of attachments not recommended or sold by SharkNinja may cause fire, electric shock, or injury.
-
During operation and handling of the appliance, avoid contact with moving parts.
-
DO NOT operate the appliance with an empty container.
-
DO NOT fill containers past the MAX FILL or MAX LIQUID lines.
-
DO NOT microwave any containers or accessories provided with the appliance.
-
DO NOT perform grinding operations.
-
Before operation, ensure all utensils are removed from containers. Failure to remove utensils can cause containers to shatter and potentially result in personal injury and property damage.
-
NEVER operate the appliance without lids and caps in place. DO NOT attempt to defeat the interlock mechanism. Ensure the container and lid are properly installed before operation.
-
DO NOT expose the containers and accessories to extreme temperature changes. They may experience damage.
-
NEVER leave the appliance unattended while in use.
-
DO NOT blend hot liquids. Doing so may result in pressure buildup and steam exposure that can pose a risk of the user being burned. Do not blend without drizzle cap securely in place.
-
If you find unmixed ingredients sticking to the sides of the cup, stop the appliance, remove the blade assembly, and use a scraper to dislodge ingredients.
-
DO NOT attempt to remove the container and lids from the motor base while the blade assembly is still spinning. Allow the appliance to come to a complete stop before removing lid and container.
SAVE THESE INSTRUCTIONS
-
Remove the Hybrid Edge™ Blades Assembly from the Ninja® Nutrient Extraction* Cup or Ninja TWISTi™ Pitcher upon completion of blending. DO NOT store ingredients before or after blending them in the cup with the blade assembly attached. Some foods may contain active ingredients or release gases that will expand if left in a sealed container, resulting in excessive pressure buildup that can pose a risk of injury. For ingredient storage in the cup, use only Spout Lid.
-
If the appliance overheats, a thermal switch will activate and temporarily disable the motor. To reset,
unplug the appliance and allow it to cool for approximately 15 minutes before using again. -
The maximum wattage rating for this appliance is based on the configuration of the Hybrid Edge Blades Assembly and Ninja TWISTi Pitcher. Other configurations may draw less power or current.
-
DO NOT process dry ingredients without adding liquid to the Ninja Nutrient Extraction* Cup or Ninja TWISTi Pitcher. They are not intended for dry blending.
-
To protect against risk of electrical shock, DO NOT immerse the motor base in water or other liquid. Unplug the motor base before cleaning.
-
Keep drizzle hole covered while processing.
-
Add liquids only through the drizzle hole and do not fill past max fill lines.
*Extract a drink containing vitamins and nutrients from fruits and vegetables.
PARTS
NOTE:
- The Hybrid Edge™ Blades Assembly is not compatible with other Ninja products.
- The number of cups, lids, and Auto-iQ programs vary by model.
A 34 oz. TWISTi Pitcher
B Motor Base (attached power cord not shown)
C Lid with Built-in Tamper and Drizzle Hole
D Hybrid Edge Blades Assembly
E Spout Lid
F Nutrient Extraction* Cup
- Extract a drink containing vitamins and nutrients from fruits and vegetables.
To purchase more accessories and find great recipes, visit ninjakitchen.com.
BEFORE FIRST USE
IMPORTANT : Review all warnings before proceeding.
NOTE : All attachments are BPA-free and dishwasher safe. Ensure blade
assembly and lids are removed from the containers before placing in the
dishwasher. Exercise care when handling blade assemblies.
- Remove all packaging materials from the unit. Wash containers, lids, and blade assembly in warm, soapy water using a dishwashing utensil with a handle to avoid direct contact with the blades. Exercise care when unpacking and handling blade assembly, as the blades are sharp.
- Thoroughly rinse and air-dry all parts.
GETTING TO KNOW THE TWIST PITCHER
Powering through tough and frozen ingredients used to require a lot of stopping, scraping, and recipe tinkering. With our new TWISTi pitcher, it is easier than ever to create thick and spoonable smoothie bowls, nut kinds of butter and more. All you have to do is twist the built-in tamper on the lid while blending to push ingredients down toward the blades
USING THE CONTROL PANEL
NOTE : For best results when making thicker recipes, use the BOWL or
SPREAD program and twist the built-tamper continuously while
processing.
AUTO-IQ® PROGRAMS
Intelligent preset programs combine unique blending and pausing patterns that
do the work for you.
Once a preset program is selected, it will start immediately and automatically
stop when blending is complete. To stop blending before the end of the
program, press the currently active button again.
EXTRACT
Ideal for tough, leafy, or fibrous whole fruits and vegetables, including
their skins, seeds, and stems.
SMOOTHIE (not included with all models)
Combine your favorite fresh or frozen ingredients, liquids, and powders to
create smoothies and protein shakes.
FROZEN
Crush ice and frozen fruit into restaurant-style frozen drinks.
SPREAD (not included with all models)
Create anything from spreadable nut butter to zesty dressings to the perfect
hummus.
BOWL
Make thick, spoonable smoothie bowls, creamy frozen yogurt, and refreshing
sorbets.
MANUAL MODE
START/STOP
Press once to start continuous running up to 60 seconds; press again to stop.
Can also be pressed to stop a running Auto-iQ program.
PULSE
Offers greater control of pulsing and blending. Operates only when PULSE is
pressed. Use short presses for short pulses and long presses for long pulses.
NOTE : Manual programs cannot be used in conjunction with any Auto-iQ
programs.
USING THE NINJA® TWISTI™ PITCHER
IMPORTANT: Review all warnings before proceeding.
NOTE:
- While processing thick ingredients, twist the built-in tamper counterclockwise continuously.
- Keep the drizzle cap closed while processing liquids.
-
Place the motor base on a clean, dry, level surface such as a countertop or table, then plug in the unit.
-
Screw on the Hybrid Edge™ Blade Assembly until you have a tight seal. Fill pitcher with desired contents up to your chosen serving lines.
-
If making a smoothie bowl, for single-serving use the lines or for two servings use the lines.
-
Install the lid by aligning the red rectangle on the lid with the red line on the top surface of the pitcher handle. Rotate the tab of the lid with the release button clockwise into the pitcher handle to lock into place.
-
Install the pitcher on the motor base by aligning the tabs on the pitcher to the slots on the base. Rotate the pitcher clockwise until it clicks into place. Programs will illuminate when unit is ready to use.
6a If using an Auto-iQ® program, select the program that best suits your desired output. For thick outputs, twist the built-in tamper on the lid counterclockwise continuously while processing. To stop the unit at any time, press the currently active program again.
6b If using START/STOP, when the ingredients have reached your desired consistency, press the button again, or wait for the unit to come to a complete stop after 60 seconds. If making thick outputs, twist the built-in tamper counterclockwise continuously while processing. If using PULSE, use short presses for short pulses and long presses for long pulses.
6c If results are too thick, open the drizzle hole cap and add more liquid. Close the cap and continue twisting the tamper counterclockwise during blending. -
Remove the lid by pressing the button on the tab until it opens. Lift up to remove. Remove the pitcher from the motor base by turning it counterclockwise and then lifting it up.
-
To enjoy on the go, pour into a Nutrient Extraction Cup, place the Spout Lid on the top and twist lid clockwise until firmly sealed. Or pour into a resusable cup of choice.
-
Remove the blade assembly by twisting counterclockwise. DO NOT store blended contents with the blade assembly attached. Exercise care when handling the blade assembly, as the blades are sharp.
-
Unplug the unit when finished. Refer to the Care & Maintenance section for cleaning and storage instructions.
USING THE NINJA® NUTRIENT EXTRACTION* CUP
IMPORTANT : Review all warnings before proceeding.
-
Place the motor base on a clean, dry, level surface such as a countertop or table, then plug in the unit.
-
Add ingredients to the Nutrient Extraction* Cup. DO NOT add ingredients past the MAX LIQUID line.
-
Place the Hybrid Edge™ Blades Assembly on the top of the cup and turn clockwise to seal.
-
Turn the cup upside down and install on the motor base by aligning the tabs on the cup with the slots on the base. Then, rotate cup clockwise until it clicks. Once locked in place, the programs will illuminate and the unit will be ready for use.
-
If using an Auto-iQ® program, select the program that best
suits your desired output. The preset feature will automatically
stop at the end of the program. To stop the unit at any time,
press the currently active program again.
5b If using START/STOP, when the ingredients have reached your desired consistency, press the button again, or wait for the unit to come to a complete stop after 60 seconds. If using PULSE, use short presses for short pulses and long presses for long pulses. -
Remove the cup from the motor base by turning the cup counterclockwise and then lifting it up.
-
Remove the blade assembly by twisting counterclockwise.
DO NOT store blended contents with the blade assembly attached. Only use the Spout Lid. Exercise care when handling the blade assembly, as the blades are sharp. -
To enjoy on the go, place the Spout Lid onto the cup and twist lid clockwise until firmly sealed.
-
Unplug the unit when finished. Refer to the Care & Maintenance section for cleaning and storage instructions.
CARE & MAINTENANCE
CLEANING
-
Hand-Washing
Wash containers, lids, and blade assembly in warm, soapy water. Use a dishwashing utensil with handle to avoid direct contact with the blades. Exercise care when handling the blade assembly as the blades are sharp. Thoroughly rinse and air-dry all parts. -
Stuck-on ingredients in the pitcher
For stuck-on ingredients, place 1 or 2 small drops of dish soap into the pitcher, and add warm water up to the single-serve Liquid Fill line. Install lid and blend on BOWL program. Twist the built-in tamper counterclockwise continuously while cleaning. -
Dishwasher
Containers, lids, and blade assembly are dishwasher safe. Ensure the blade assembly and lid are removed from the container before placing in the dishwasher. -
Motor Base
Turn off the unit and unplug the motor base before cleaning. Wipe motor base with a clean, damp cloth.
DO NOT use abrasive cloths, pads, or brushes to clean the base.
STORING
For cord storage, wrap cord with a hook-and-loop fastener near the back of the motor base. DO NOT wrap the cord around the bottom of the motor base.
DO NOT store blended or unblended ingredients in the cup or pitcher with the blade assembly attached.
Use only the spout lid when storing blended or unblended ingredients in the cup.
DO NOT stack items on top of the containers. Store any remaining attachments alongside the unit or in a cabinet where they will not be damaged or create a hazard.
RESETTING THE MOTOR THERMOSTAT
This unit features a unique safety system that prevents damage to the motor
and drive system should you inadvertently overload it. If the unit is
overloaded, the motor will be temporarily disabled. Should this occur, follow
the reset procedure below.
- Unplug the unit from the electrical outlet.
- Allow the unit to cool for approximately 15 minutes.
- Remove the blade assembly from the container. Empty the container and ensure no ingredients are jamming the blade assembly.
IMPORTANT : Ensure that maximum capacities are not exceeded. This is the
most typical cause of appliance overload.
If your unit needs service, call Customer Service at
1-877-646-5288. So we may better assist
you, please register your product online at registeryourninja.com and have the
product on hand when you call.
ORDERING REPLACEMENT PARTS
To order additional parts and attachments, visit ninjaaccessories.com.
TROUBLESHOOTING GUIDE
WARNING: To reduce the risk of shock and unintended operation, turn the
power off and unplug the unit before troubleshooting.
The display reads “- -”.
-
If the vessel is properly installed and the display reads ‘- -’, ensure the interior of the base area is clean of any debris.
The Control panel does not illuminate. -
Make sure the unit is plugged in. If the unit is plugged in and no container is installed, the unit will display ‘- -’. The available programs will illuminate after placing a container on base and rotating it clockwise until it clicks into place.
Control panel doesn’t turn off. -
Remove the container from the base by rotating it counterclockwise and lifting it up. The display with flash ‘- -’. Unplug the power cord from the outlet. If the unit remains plugged in, the display will time out after 3 minutes of inactivity. Press any button to wake the unit.
Doesn’t mix well; ingredients get stuck. -
Using the Auto-iQ® programs is the easiest way to achieve great results. The pulses and pauses allow the ingredients to settle toward the blade assembly. If ingredients are routinely getting stuck, adding some liquid will usually help.
-
When filling the cup, start with fresh fruit or veggies, then leafy greens or herbs. Next, add liquids or yogurt, then seeds, powders, or nut butter. Finally, add ice or frozen ingredients.
-
If using the TWISTi Pitcher, during the blending process twist the built-in tamper counterclockwise continuously to circulate ingredients.
Unit moves on the counter while blending. -
Make sure the counter and feet of the unit are clean and dry.
Lid or Hybrid Edge™ Blades Assembly is hard to install on the container. -
Set the container on a level surface. Carefully place the lid or blade assembly on the top of the container and align the threads so the lid/blade assembly sits flat. Twist clockwise until you have a tight seal.
Can’t remove the tamper from the pitcher lid for cleaning. -
The tamper is built-in and not removable from the pitcher lid.
The display reads “E1” -
If the display reads “E1”, the motor has been running for too long. As a safety feature, we recommend running the unit for less than 3 minutes consecutively. Unplug the unit and let it cool for 15 minutes before running again.
PRODUCT REGISTRATION
Please visit registeryourninja.com to register
your new Ninja® product within ten (10) days of purchase. You will be asked to
provide the store name, date of purchase,
and model number along with your name and address.
The registration will enable us to contact you in the unlikely event of a
product safety notification.
By registering, you acknowledge you have read and understood the instructions
for use and warnings set forth in the accompanying instructions.
ONE (1) YEAR LIMITED WARRANTY
The One (1) Year Limited Warranty applies to purchases made from authorized
retailers of SharkNinja Operating LLC. Warranty coverage applies to the
original owner and to the original product only and is not transferable.
SharkNinja warrants that the unit shall be free from defects in material and
workmanship for a period of one (1) year from the date of purchase when it is
used under normal household conditions and maintained according to the
requirements outlined in the Owner’s Guide, subject to the following
conditions and exclusions:
What is covered by this warranty?
- The original unit and/or non-wearable parts deemed defective, in SharkNinja’s sole discretion, will be repaired or replaced up to one (1) year from the original purchase date.
- In the event a replacement unit is issued, the warranty coverage ends six (6) months following the receipt date of the replacement unit or the remainder of the existing warranty, whichever is later. SharkNinja reserves the right to replace the unit with one of equal or greater value.
What is not covered by this warranty?
- Normal wear and tear of wearable parts (such as blending vessels, lids, blades, blender bases, etc.), which require regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered by this warranty. Replacement parts are available for purchase at ninjaaccessories.com.
- Any unit that has been tampered with or used for commercial purposes
- Damage caused by misuse, abuse, negligent handling, failure to perform required maintenance (e.g., failure to keep the well of the motor base clear of food spills and other debris), or damage due to mishandling in transit.
- Consequential and incidental damages.
- Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the repair is performed by a repair person not authorized by SharkNinja.
- Products purchased, used, or operated outside North America.
How to get service
If your appliance fails to operate properly while in use under normal
household conditions within the warranty period, visit
ninjakitchen.com/support for product care
and maintenance self-help. Our Customer Service Specialists are also available
at 1-877-646-5288 to assist with
product support and warranty service options, including the possibility of
upgrading to our VIP warranty service options for select product categories.
So we may better assist you, please register your product online at
registeryourninja.com and have the product on
hand when you call. SharkNinja will cover the cost for the customer to send in
the unit to us for repair or replacement. A fee
of $20.95 (subject to change) will be charged when SharkNinja ships the
repaired or replacement unit.
How to initiate a warranty claim
You must call 1-877-646-5288 to
initiate a warranty claim. You will need the receipt as proof of purchase. We
also ask that you register your product online at
registeryourninja.com and have the product on
hand when you call, so we may better assist you. A Customer Service Specialist
will provide you with return and packing instruction information.
How state law applies
This warranty gives you specific legal rights, and you also may have other
rights that vary from state to state. Some states do not permit the exclusion
or limitation of incidental or consequential damages, so the above may not
apply to you.
NOTES …………
REGISTER YOUR PURCHASE
registeryourninja.com
Scan QR code using mobile device
RECORD THIS INFORMATION
Model Number: ____
Serial Number: __
Date of Purchase:
(Keep receipt)
Store of Purchase: __
TECHNICAL SPECIFICATIONS
Voltage:
120V~, 60Hz
Power:
1100 Watts
SharkNinja Operating LLC
US: Needham, MA 02494
CAN: Ville St-Laurent, QC H4S 1A7
1-877-646-5288
ninjakitchen.com
Illustrations may differ from the actual products. We are constantly
striving to improve our products,
therefore the specifications contained herein are subject to change without
notice.
AUTO-IQ and NINJA are registered trademarks of SharkNinja Operating LLC.
HYBRID EDGE and TWIST are trademarks of SharkNinja Operating LLC.
This product may be covered by one or more U.S. patents.
See sharkninja.com/patents for more information.
© 2022 SharkNinja Operating LLC
SS150Series_IB_MP_Mv3
@ninjakitchen
Documents / Resources
|
NINJA SS150 Series Twisti High-Speed Blender
Duo
[pdf] Instruction Manual
SS150 Series, Twisti High-Speed Blender Duo, SS150 Series Twisti High-Speed
Blender Duo, SS150
---|---
|
NINJA SS150 Series Twisti High-Speed Blender
Duo
[pdf] Instruction Manual
SS150 Series Twisti High-Speed Blender Duo, SS150 Series, Twisti High-Speed
Blender Duo, High-Speed Blender Duo, Blender Duo, Duo
|
NINJA SS150 Series Twisti High Speed Blender
Duo
[pdf] User Manual
SS150 Series Twisti High Speed Blender Duo, SS150 Series, SS150 Series Blender
Duo, Twisti High Speed Blender Duo, High Speed Blender Duo, Twisti Blender
Duo, Blender Duo, Blender
|
NINJA SS150 Series Twisti High Speed Blender
Duo
[pdf] Owner's Manual
SS150 Series Twisti High Speed Blender Duo, SS150 Series, Twisti High Speed
Blender Duo, Speed Blender Duo, Blender Duo
|
NINJA SS150 Series Twisti High-Speed Blender
Duo
[pdf] Owner's Manual
SS150 Series Twisti High-Speed Blender Duo, SS150 Series, Twisti High-Speed
Blender Duo, High-Speed Blender Duo, Blender Duo
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>