Draperies BR-25-1140USB Tubular Motor Instructions

Draperies BR-25-1140USB Tubular Motor

SAFETY NOTE

1. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
2. Children shall not play with the appliance.
3. Cleaning and user maintenance shall not be made by children without supervision.
4. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
5. WARNING: the drive shall be disconnected from its power source during cleaning, maintenance and when replacing parts.
6. The instructions shall state that the A-weighted emis sion sound pressure level of the drive is equal to or
7. The mass and the dimension of the driven part shall be compatible with the rated torque and rated operating time.
8. The type of driven part the drive is intended for.
9. WARNING: Important safety instructions. It is important for the safety of persons to follow these instructions. Save these instructions.
10. Do not allow children to play with fixed controls. Keep remote controls away from children.
11. Frequently examine the installation for imbalance and signs of wear or damage to cables and springs. Do not use if repair or adjustment is necessary.
12. Watch the moving shutter and keep people away until the shutter is completely closed.
13. WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury.
14. Before installing the drive, remove any unnecessary cords and disable any equipment not needed for powered operation.

Instruction

Features

• Built-in Receiver
• Jog & Tilt
• Built-in Lithium Battery
• Scan and Program
• Status Feedback
• Switch Direction
• Stall Protection
• Program Button
• Reset to Factory Mode
• Memorized Setting
• Electronic Limit
• Preferred Stop Position
• Speed Regulation
• Scene Control

Fields of Application

The motor is suitable for the motorization of roller blinds.

Specifications

Following data for reference

Model

| Rated Torque (N.m)| Rated Speed (rpm)| Rated Power (W)
---|---|---|---
DM25LEU/S-0.7/34| 0.7| 34| 8
DM25LEU/S-1.1/28| 1.1| 28| 10
DM25LEU/S-1.1/40| 1.1| 40| 10

For reference only

Attention

Never drop, knock, drill or submerge the motor. Keep the power cable in the right position as follows. Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void the manufacturer’s liability and warranty.

Charging Instructions

This motor has a built in Li-ion battery pack with integrated charge management. Max power input for recharging: 5V 2A. Before first use please charge motor for 6 hours. Using 5V charger (most phones charger is 5V ) . During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and needs to be charged.
During operation, the voltage was detected to be too low, the battery was about to run out, the battery stopped running and needed to be recharged.

Rechargeable Battery

Motor Installation

1. Step 1 Cut drive tube to required length.
2. Step 2 Ensure tube edge is clean and burr-free.
3. Step 3 Mount correct crown & drive adapter on the motor. Make sure drive adapter fits firmly and crown rotates freely.
4. Step 3 Mount correct crown & drive adapter on the motor. Make sure drive adapter fits firmly and crown rotates freely.

Caution

1. Do not expose motor to humid or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna and keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If power cable or connector is damaged, do not use.
6. Ensure correct crown and drive adaptor are used.
7. Ensure power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls shall be properly isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
11. Installation and programming to be performed by a qualified professional, use or modification outside the scope of this instruction may void warranty.

Important Safety Instructions To Be Read Prior To Operation

Setting Notice
Please read following points of attention carefully before setting.

1. Don’t operate motors when low voltage alarm.

2. Operating：
   The valid interval of the emitter button is 10S, the emitter will quit the set after 10S.
   The motor will run or beep for hint, please do the next step after the hint.

3. Set the limit position：
   After the upper / lower limit setting, and the upper / lower limit positin can’t at the same position. After the limit setting, with power off and memory function.
   Limit delete will clear all limit memory.
   It will exit limit setting when program there is no operation for 2 minutes.

4. If the emitter lost, please set up again with the new emitter.

5. One motor can store maximum 10 channels; after fully stored, if pair new channels, only the last one will be covered circularly.

Button Instructions

Dial lithium battery switch, 0 is off switch, 1 is turn on switch.
Functions of P1 button

1. Cycle Operation：

2. Pairing or Pair Additional Emitter：Press P1 button for 2S, motor jog once, release button and make a long noise, motor is ready for pairing or pair additional emitter.

3. Radio Lock: Press and hold P1 button for 6S, the motor will jog twice, release button and beep twice, the motor enters radio lock status, the motor won’t receive any signal; press P1 button once to disable Radio Lock.

4. Switch Direction:
   Press and hold P1 button for 10S, the motor will jog 3 times, release button and beep 3 times, the running direction of the motor has been changed.

5. Reset to Factory Mode:
   Press and hold P1 button for 14S, the motor will jog 4 times, release button and beep 4 times, the motor has been reset to factory mode.At this point the motor will go into deep sleep. After entering deep sleep, the motor can’t be controlled. At this time, you need to press P1 button for 2S and then the motor turns to prompt to exit deep sleep.

Essential Settings
The steps in factory mode must be completed to ensure proper operation.

Factory mode

Pairing

Press P1 button for 2S (1 jog ), release button and make a long noise, Or turn the DIP switch to “0” and then to “1” (1 jog and make a long noise), repower the motor, within 10S, press STOP for 2S (2 jogs and 3 beeps ), the motor has been paired successfully.
Re-power on after power off, if the motor has saved the emitter, there is no rotation prompt, and the code matching status is not automatically entered at this time.

 Switch Rotating Direction (Optional)

If press UP, the motor runs downward, try below to switch direction
Press and hold UP and DOWN buttons simultaneously for 2S, motor jog once, the direction has been switched successfully.
The operation is only valid when there is no limits. If the motor has already set the upper and lower limit, then you can only switch direction by P1 button.

Upper and Lower Limits Setting

1. Set upper limit
2. Set lower limit

After the limits have been set successfully, the motor will enter the user mode.
User mode

1. Add A Preferred Position
   Check both upper and lower limits are set. Operate the product to desired preferred position. Press P2 (1 jog and 1 beep), press STOP(1 jog and 1 beep), STOP again (2 jogs and 3 beeps), the preferred position is set.

2. Remove preferred position
   Press P2 (1 jog and 1 beep), press STOP (1 jog and 1 beep), STOP again(1 jog and make a long noise), the preferred position is deleted.

Jog Mode & Running Mode Switch

Press and hold UP and DOWN buttons simultaneously for 5S (1 jog), press STOP (1 jog and make a long noise), switch to jog mode, If motor jog twice and beep 3 times, switch to running mode.

Adjust Limits

Press and hold DOWN and STOP buttons for 5S (1 jog and make a long noise), operate the product to desired new lower limit position, press and hold DOWN and STOP buttons for 2S (2 jogs and 3 beeps), the new lower limit is programmed successfully.
After entering the limits fine tuning mode, the original preferred position will not be deleted; If there is no button operation within 2 minutes, it will arrive within 2 minutes, and the motor will turn to prompt, and automatically exit the route adjustment mode; When fine-tuning the limit, press and P1 for more than 2S to exit the mode.

Pair / Unpair Additional Emitter

Press P2 (1 jog and 1 beep) and P2 (1 jog and 1 beep) on existing emitter, press P2 on new emitter to add (2 jogs and 3 beeps), new emitter is paired to the motor.
Press P2 (1 jog and 1 beep) and P2 (1 jog and 1 beep) on existing emitter, press STOP on new emitter for 2S to add (2 jogs and 3 beeps), new emitter is paired to the motor.
Press P1 button for 2S (1 jog), release button and make a long noise, press STOP on new emitter for 2S to add (2 jogs and 3 beeps), new emitter is paired to the motor.

Speed Regulation

Press P2 (1 jog and 1 beep), UP (1 jog and 1 beep), UP again (2 jogs and 1 beep), the motor running speed is accelerated .

Press P2 (1 jog and 1 beep), DOWN (1 jog and 1 beep), DOWN again (2 jogs and 1 beep), the motor running speed is decelerated.

Quick Index

|

Settings

|

Steps

---|---|---
1| Pairing| P1 (hold down 2s) Stop (hold down 2s)

2

| Switch Rotating Direction| Up + Down (hold down 2s)

3

|

Upper and Lower Limits Setting

| Set upper limit|  p (hold down 2s) p + Stop (hold down 2s)
Set lower limit| Down (hold down 2s) Down + Stop (hold down 2s)
4| Add / Remove Preferred Position| P2 Stop Stop

5

| Jog Mode & Running Mode Switch|  p + Down (hold down 5s) Stop

6

|

Adjust Limits

| Adjusting the upper limit|  p + Stop (hold down 5s) p or Down p + Stop (hold down 2s)
Adjusting the lower limit| Down + Stop (hold down 5s) p or Down Down + Stop (hold down 2s)

7

|

Pair / Unpair Additional Emitter

| P2(a) P2 (a) P2(b)
P2(a) P2 (a) Stop (b) (hold down 2s)
P1 (hold down 2s) Stop (b) (hold down 2s)

8

|

Speed Regulation

| Acceleration setting| P2 Up Up
Deceleration setting| P2 Down Down

Troubleshooting

The motor has no response

| Battery in motor is depleted| Recharge with compatible AC adaptor
Power Failure Or Incorrect Connection| Double check power and cable connections, follow wiring instructions.
emitter battery is low capacity| Replace battery
Radio interference / shielding| Check antenna on motor is intact and exposed. Check for possible source of radio interference.
Out of radio control range| Try control within closer range

The emitter cann’t control single motor

|

Multiple motors are paired to the same channel.

| Pair single motor with emitter correctly
Try to use multi-channel emitters to control multi-motor projects, ensure each channel to control one single motor
The motor doesn’t run or starts too slowly or make loud noise| Connections are incorrect.| Check connections
Installation is improper or overload| Check installation or overload
The motor stops during the up and down running| The motor has reached the lower limit| Adjust the new lower limit
The running time more than 6min| Consult the sales for more information

FCC Rules

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause harmful interference,  and  (2)  this device must accept any interference received, including interference that may cause undesired operation.

NOTE 1: This equipment has been tested and found to comply with the limits for a  Class  B digital device, pursuant to part 15 of the  FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and,   if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If  this  equipment  does cause harmful     interference  to radio    or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the  interference by  on  or more  of   the following measures:

• Reorient or relocate the receiving
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

References

• Die Welt der Mode | Mode.at

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>