Bridgetek LEW2022 DSBus USB Adapter User Guide

June 12, 2024
Bridgetek

LEW2022 DSBus USB Adapter

Product Information: LDSBus USB Adapter

The LDSBus USB Adapter is a versatile device that serves two
functions:

  1. Configuring LDSBus Devices (Sensors/Actuators)
  2. Creating an LDSBus

Setup Instructions:

  1. Configuring LDSBus Devices:

  2. Step 1: Connect the LDSBus USB Adapter to a PC
    with a USB-C to USB-A (or USB-C to USB-C) cable.

  3. Step 2: Ensure that the LDSBus Device is
    connected to its cable at one end.

  4. Step 3: Attach the other end of the cable to
    the LDSBus USB Adapter.

  5. Step 4: Scan the QR code or visit the link
    provided below to download the LDSBus Configuration Utility and
    obtain step-by-step instructions for configuration.

  6. Creating an LDSBus:

  7. Step 1: Connect the LDSBus USB Adapter to a
    USB Host (Windows/Linux PC, RPi3/4, or other supported hosts).

  8. Step 2: Connect a 24VDC/18W power adapter to
    the DC jack and power on. (Power to the LDSBus will be enabled by
    software.)

  9. Step 3: Connect the first LDSBus HVT-Junction
    to the LDSBus USB Adapter using an RJ45 (CAT5e) Cable.

  10. Step 4: If there is more than one LDSBus
    HVTJunction, chain them together as shown.

  11. Step 5: Scan the QR code or visit the link
    provided below to download software to operate the bus.

Note: Enable termination for the last LDSBus
Device in the bus using the LDSBus Configuration Utility.

Please scan QR code A or visit http://bit.ly/system-warranty
for warranty information.

View the full information of the LDSBus USB Adapter, application
setup, and installation at http://bit.ly/ldsbus-resources
or scan QR Code B.

USB Adapter
Quick Start Guide

Setup Instructions:
The LDSBus USB Adapter serves two functions: 1) Configure LDSBus Devices 2) Create an LDSBus

  1. To Configure LDSBus Device (Sensors/Actuators)

Step 1:
Connect the LDSBus USB Adapter to a PC with a USB-C to USB-A (or USB-C to USB-C) cable.

Step 2:
Ensure that the LDSBus Device is connected to its
cable at one end.

Step 3:
Attach the other end of the cable to the LDSBus USB Adapter as shown.

Step 4:
Scan the QR code or visit the link provided below to download the LDSBus Configuration Utility and obtain step by step instructions for configuration.

  1. To Create an LDSBus

Step 1:
Connect the LDSBus USB Adapter to a USB Host. (Windows/Linux PC, RPi3/4 or other supported hosts)

Step 2:
Connect a 24VDC/18W power adapter to the DC jack and power on. (Power to the LDSBus will be enabled by software)

Step 3:
Connect the first LDSBus HVT-Junction to the LDSBus USB Adapter using a RJ45 (CAT5e) Cable.

Step 4:
If there is more than one LDSBus HVTJunction, chain them together as shown.

Step 5:
Scan the QR code or visit the link provided below to download software to operate the bus.

Note: Enable termination for last LDSBus Device in the bus using the LDSBus Configuration Utility

Please scan QR code A or visit

http://bit.ly/system-warranty for warranty

A

View the full information of the LDSBus USB Adapter, application setup and installation at

B

registration using the UUID and Product Key

http://bit.ly/ldsbus-resources

Sticker Area

or scan QR Code B.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals