BACKFIRE HALO Remote Hammer Sledge User Guide

: October 27, 2023
: BACKFIRE

Table of Contents

Remote Layout
Technical Info
Dashboard Layout
Pairing Instructions
Ride Modes
Battery Status
Advanced Setting
Fingerprint Setup
Restore Factory Settings and Updating Firmware
Charging Status
Tank Turn Mode
Rider Controls
Malfunctions
Tips
Gear Ratio and Pole Pair Configurations
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BACKFIRE HALO Remote Hammer Sledge User Guide

Remote Layout

single button to power on/off your board and remote.
Backfire boards can stay in standby mode for up to a day, within which the remote can be used to power the board on or off.
Double clicking the Power Button turns on the board’s ambient lights. The color of the lighting changes with the riding mode.

Technical Info

Aluminum Housing
Battery Capacity: 1000mAh
Display Size: 1.3 inch
LCD Panel
Voltage: 5V
Weight：130g
3hr Charge Time
Fingerprint Sensor

Dashboard Layout

Enable

Bluetooth Enabled Connect to the Backfire APP for Firmware Updates

Enable

Cruise Control Enabled

Enable Unlocked

Fingerprint Unlock Enabled Remote automatically locks itself after 6 seconds of inactivity to prevent accidental inputs

TRIP:14 KM
Current Trip Meter Displays the distance traveled since the board was powered on
TRIP:14 KM
Current Trip Meter Displays the distance traveled since the board was powered on
ODO: 1142 KM
Odometer
Displays the total distance traveled since the remote was first paired with the board. Mileage is retained and unique to each board.
R
Remote Battery Indicator
B
Board Battery Indicator
20
Current Speed

Pairing Instructions

Hold the Power Button for 3 seconds to power ON/OFF the board.

When both the remote and board are in the OFF state, hold the Power Button on both the board and remote at the same time for 3 seconds to pair.

In the 4WD configuration, the rear controller (ESC1) should be paired before the front (ESC2).
Pairing Instructions

Pairing Instructions

Ride Modes

Default Mode after Pairing.
Press the S/E Button once to activate Sport mode. The remote display will turn blue/red and vibrate once.
Press the Turbo Button once to engage Turbo Mode.

Cruise Control Mode

While riding, press the Power Button then release the Throttle Wheel to engage Cruise Control Mode.

Battery Status

While the board is stationary, press the Power Button once to open the settings menu
Select Remote Power to display the Battery Status, Time Since Power On, and Battery Capacity. Press the S/E Button to return to the Previous Menu.
Select Board Power to display the Battery Voltage, Remaining Capacity, Temperature, and Battery Health. [Blue: Healthy, Red: Unbalanced]
In the event one or more of the cells are unbalanced, contact the Backfire Support Team or use the Backfire Balance Charger to restore the pack to a healthy state

Advanced Setting

Select Motor & ESC to display their temperatures.
Select Sport Setting to adjust the Speed, Acceleration and Brake profile for Sport Mode.
Select ECO Setting to adjust the Speed, Acceleration and Brake profile for ECO Mode.
Select Turbo Setting to adjust the Speed, Acceleration and Brake profile for Turbo Mode.

Fingerprint Setup

Select Fingerprint Settings to add and remove fingerprints. A total of 3 fingerprints can be stored on the remote.
Multiple fingerprint calibration cycles are required for maximum reliability and accuracy
To add a fingerprint, place your finger on the sensor until the remote vibrates, then lift it off and repeat until the status displays 100%
The Safety Switch option enables/disables fingerprint unlock.
To remove all stored fingerprints, select the Delete Fingerprints option
Single fingerprint delete is currently not supported.

Restore Factory Settings and Updating Firmware

Select Restore Setting to Restore the Remote to its Factory Calibrated Settings.
Select Firmware Update to Update the Remote Firmware

Charging Status

Board: Charging
Remote: Charging
Board: Not Charging
Remote: Charging
Board: Charging
Remote: Not Charging
Board: Not Connected
Remote: Charging
Board: Fully Charged
Remote: Fully Charged

Tank Turn Mode

Press the Turbo Button twice to engage Tank Turn Mode. Press the Power Button once to disengage.
Ride Modes

Warning: Keep clear of the board when Tank Turn Mode is engaged. Standing on it may lead to serious injury.

Rider Controls

For beginners and children, we recommend donning protective gear and starting out with ECO Mode. Roll the Throttle Wheel forwards in small increments to accelerate gently. Position your feet slightly wider than shoulder-width on the deck and bend your knees slightly to lower your center of gravity.
Rider Controls

Lean forward when accelerating to prevent falling backwards when the torque kicks in.
Lean back when braking to prevent being thrown forward by the sudden deceleration.