baliv WT-5760 Series Washbasin Faucet Matt Instruction Manual
- June 6, 2024
- baliv
Table of Contents
baliv WT-5760 Series Washbasin Faucet Matt
INSTALLATION
Before you begin
Intended use
The product is at the current level of science and technology and meets all valid safety requirements in place at the point of introduction, assuming proper use. This faucet is designed for sanitary use only. The product is not designed for commercial use. Any other type of use is inappropriate. Improper use or modifications to the product or the use of components that are not tested and approved by the manufacturer may result in unforeseen damage! Any unintended use or any activities on the product not described in these operating instructions are an unauthorized misuse outside the manufacturer’s legal liability limits.
For your safety
General safety information
- The user of the product must have read and understood these operating instructions prior to its first use to ensure the safe handling of this product.
- Please comply with all safety instructions!
- Store all operating information and safety instructions for future reference.
- If you sell or pass on the product, you must also pass on these operating instructions.
- The product may only be used when it functions properly. If the product or part of the product is defective, take it out of operation and ensure that it is disposed of correctly.
- Only use the product for its intended purpose.
Product-specific safety information
-
Important when using in low-pressure systems: Before starting up the low pressure or electrical storage heater open the hot water faucet of the faucet unit until the water flows without bubbles.
Note: A low-pressure faucet drips when heating water since it functions like a pressure control valve. -
Faucet for use in private households! Only suitable for use in rooms with a temperature above 0° C. In the event of a risk of frost, interrupt the water supply and empty the faucet.
-
Be careful when setting the hot water: Risk of scalding!
-
If the faucet is not used for a longer period of time, first run a large amount of water through it before taking water for drinking.
-
Symbols affixed to your product may not be removed or covered. Information on the product that is no longer legible must be replaced immediately.
-
Before putting the unit into operation, read and observe the operating instructions.
-
Read and observe the notes regarding cleaning agents
-
Faucet for use on washbasins
-
Hot water connection
-
Coldwater connection
-
Observe the more detailed information on the next pages
-
Optional fixture sets. Check the scope of delivery prior to installation. Depending on the faucet, there are fixture sets included in the scope of delivery that may differ from the one depicted.
-
Information regarding the fixture of water pipes
Installation
Note: The images show examples, the fittings may differ from those depicted in terms of appearance and scope of delivery. Pay attention to the article number on the packaging!
CAUTION! Risk of water damage! Installation must be carried out by an installation engineer or by a technically-versed end-user instructed by an installation engineer. Failure to observe this requirement shall void the warranty. Prior to the installation and disassembly of a faucet, the general water supply should be switched off. When installing the new faucet ensure that the seals are positioned correctly. After installation, check all connections to ensure that they are sealed and test the faucet for functionality. Pipes and fittings must be installed, inspected, and flushed in accordance with current standards and regulations.
- After installation, unscrew the mixer jet, rinse the pipe and the faucet well (hot/cold water supply) in order to rinse out contaminations (shavings and hemp residues). Screw the mixer jet back onto the outlet after rinsing the faucet.
- Leaks or water outs may cause considerable damages to the building or to the contents of your home. Check all connections carefully to ensure that they are sealed.
NOTICE! Risk of damage to the product! Only hand tighten the connection hoses. If tightened excessively, the threaded section may break off.
Replacing the cartridge
The cartridge is a consumable that may, in the event of very hard or dirty
water, need to be replaced every 1 to 2 years.
Cleaning
NOTICE! Risk of damage to the product! Do not metallic cleaning products. Do not use aggressive cleaning agents or solvents. Sanitary faucets require special care. For this reason, please observe the following notes:
- Chrome-plate surfaces are sensitive to limescale removal products, acidic cleaning agents and all types of scouring agents.
- Colored surfaces may not be cleaned with scouring or corrosive agents or those containing alcohol.
- Clean your faucets with clean water and a soft cloth or chamois leather only.
Disposal of the product
This product may not be disposed of with household waste! Ensure it is
disposed of professionally. Information can be obtained from the relevant
waste disposal authorities.
Disposing of the packaging
The packaging consists of cardboard and marked plastics that can be recycled.
Technical data
Part number 212257
Flow pressure (recommended) 1.5 bar
- If the pressure is greater than 2 bar installs a pres-sure reducer!
Water temperature Maximum 80°C