Shenzhen Liangming Technology LM80P2-0001AA Wireless Module User Manual
- June 6, 2024
- Shenzhen Liangming Technology
Table of Contents
Shenzhen Liangming Technology LM80P2-0001AA Wireless Module
Overview
The LM80 SoC features a fully integrated 2.4GHz radio transceiver and baseband processor for Wi-Fi 802.11b and Bluetooth® Smart applications. The SoC can be used as a standalone application-specific communication processor or as a wireless data link in hosted MCU systems where ultra-low power is critical. The OPL1000 supports flexible memory architecture for storing profiles, stacks and custom application codes, and can be updated using Over-The-Air (OTA)technology. Qualified Bluetooth Smart protocol stack and Wi-Fi TCP/IP stack are stored in a dedicated ROM. The OPL1000 is equipped with dual processors, ARM® Cortex®-M0 and M3, for handling different processes. All software runs on the ARM® Cortex®-M0 processor while more intensive application-specific activities run on the ARM® Cortex®-M3 processor. The OPL1000 can be connected to any external MCU through SPI, I2C or UART interfaces and sensors or other devices through GPIOs. The transceiver interfaces directly to the antenna and is fully compliant with the Wi-Fi 802.11b and Bluetooth 5.0 BLE standards. With integrated antenna switch, RF balun,power amplifier (PA) and low noise amplifier (LNA), the OPL1000 allows both Wi-Fi and Bluetooth Smart to minimize PCB design area and external component requirement.
FEATURES
The OPL1000 complies with ETSI EN 300 328 and EN 300 440 Class 2 (Europe), FCC CFR47 Part 15(US), and ARIB STD-T66 (Japan).
- Processors
- ARM® Cortex®-M3 Application Processor
- ARM® Cortex®-M0 Link Controller
- Wi-Fi
- 802.11b up to 11Mbps
- Supports STA mode
- WPA/WPA2 security supported
- Automatic beacon scanning and discovery
- Built-in TCP/IP stack
- Integrated dual power amplifiers: low (-2 dBm), high (+10 dBm)
- Bluetooth Smart
- Compliant with Bluetooth 5.0 BLE specifications with 2Mbps rate capability
- Slave mode support
- All GATT-based profiles supported
- Built-in BLE stack
- 0 to 10 dBm transmit output power
- 93 dBm receive sensitivity
- HW Crypto Engine
- AES-128/256 bits Encryption
- P-192/256 ECDH (Elliptic Curve Diffie-Hellman) Key Generation
- SHA2
- TRNG
- Power Management
- Integrated Buck DC-DC converter
- General purpose, capture and sleep timers
- FW OTA (Over-The-Air) update support
- Digital Interfaces
- General purpose I/Os: 24
- Two UARTs with hardware flow control up to 3Mbps
- Three SPI+™ interfaces
- One I2C bus at 100 kHz, 400 kHz
- Analog Interfaces
- 10-bit Auxiliary ADC inputs up to 16 channels
- Six GPIO pins with 16mA driving capability
- Six PWMs
- Radio Transceiver
- Fully integrated dual-mode 2.4 GHz CMOS transceiver
- Single wire antenna: no external matching and no external T/R switch required
- Package
- 48-pin QFN, 6 mm x 6 mm
Applications
- WiFi scale ·WiFi intelligent door loc
- Wearable devices or healthcare devices
- Industrial remote control and telemetry
- Traffic, underground positioning and alarm
- Automatic data acquisition system
- Wireless data transmission; banking system
- Building automation, security, wireless monitoring of computer room equipment, access control system
- Intelligent home and industrial control
FCC Modular Usage Statement
The requirement for KDB 996369 D03:
List of applicable FCC rules
FCC CFR Title 47 Part 15 Subpart C Section 15.247
Summarize the specific operational use conditions
The module has been certified for Fix, Mobile, Portable applications. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Limited module procedures
Not applicable
Trace antenna designs
Not applicable
RF exposure considerations
This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body.
Antennas
This module contains three Antenna type. The details information list bellow.
PCB Antenna:1.2dBi
IPEX Antenna:1.5dBi
FPCB Antenna:-3.49dBi
Label and compliance information
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. Warning: Changes or modifications to this unit not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment. NOTE: This equipment has been
tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed andused in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio /TV technician for help. If the
FCC identification number is not visible when the module is installed inside another device,
then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: 2AQJL- LM80P2 Or Contains FCC ID: 2AQJLLM80P2”
IC STATEMENT
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Information on test modes and additional testing requirements
The modular transmitter is only FCC authorized for the specific rule parts (FCC Part 15.247) list on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed when contains digital circuity.
Additional testing, Part 15 Subpart B disclaimer
When testing host product, the host manufacture should follow FCC KDB Publication 996369 D04 Module Integration Guide for testing the host products. The host manufacturer may operate their product during the measurements.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>