PATONA WB1-11 EV Wallbox Charging Station User Manual
- June 6, 2024
- PATONA
Table of Contents
- PATONA WB1-11 EV Wallbox Charging Station User Manual
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
PATONA WB1-11 EV Wallbox Charging Station User Manual
PATONA is a registered quality brand from Germany.
PATONA PRODUCTS ARE MADE WITH
Safety and warning instructions
Attention high voltage! The input and output voltage of the Wallbox is life-threatening!
- The Wallbox may only be disassembled, repaired, opened and installed by authorized and qualified personnel. Authorized and qualified personnel are persons who have certified skills and knowledge regarding the installation and operation of this type of electrical equipment and have received appropriate safety training.
- The manufacturer assumes no liability for consequences resulting from unqualified and/or improper use and/or installation.
- When installing a Wallbox, all local, regional and national regulations and laws must be observed.
- The Wallbox must not be installed and operated in the vicinity of explosive or flammable materials or in the vicinity of chemicals, vapors and other hazardous substances and objects.
- Children must be kept away from the Wallbox and accessories.
- The technical design of the Wallbox complies with protection class IP54. Nevertheless, care should be taken to ensure that it is not exposed to direct rain and severe weather.
- The charging connection of the Wallbox must always be clean and dry. Cleaning may only be carried out with a dry cloth.
- The base core must not be touched when switching on. Danger to life!
- Hybrid vehicles may only be charged when the engine is off.
- The vehicle must not be moved during the charging process.
- In case of a defect, cracks, strong abrasion, leakage and/or peculiar odors as well as unexpected behavior, the Wallbox must not be used. If such a case occurs, authorized and qualified personnel must be notified/called. The output and input power supply must be disconnected immediately.
- The Wallbox may only be disposed of via a suitable facility for recycling electrical equipment. Further information can be obtained from the local municipal administration.
Technical specification
Housing dimensions
Configuration and operation
Start and stop charging station with your charging card
A) Start charging process
- Plug the charging cable into the charging port of your car. The LED ring light on the Wallbox should now light up yellow.
- Hold your charging card (RFID card) in front of the Wallbox reader within 3-5 seconds.
- You will hear a beep and the LED ring light will pulse green as soon as the charging process starts.
B) End charging process
- Hold your charging card (RFID card) in front of the reader again for approx. 3 seconds.
- A beep sounds again, the LED ring light lights up green when the charging process is completed.
- Disconnect the charging cable from your car and reattach the charging cable to the cable holder.
C) Resetting the “Total” display
- Press the red emergency stop button on the wallbox three times.
Control via Bluetooth / App
A) Download the „YOOZI EV“ app from the Google PlayStore or the Apple App Store.
B) Launch the app, confirm the privacy policy and tap the Bluetooth icon to access the pairing function.
C) Connect via Bluetooth
- Add a new device.
- Enter the number of the Wallbox, which is shown on the Wallbox display, into the app or scan the QR code.
- Enter the password 123456 (can be changed later).
- Then connect the Wallbox to the app.
D) Pairing
If a connection is established, you will see „connectable“ next to the Wallbox number.
- Tap on the device number and wait about 10 seconds, the pairing is now established, the next steps can take place.
- If the pairing does not work, please switch off Bluetooth of your smartphone, wait 3 seconds and activate Bluetooth again.
- Then start the pairing process again.
E) Start charging process
- Connect the charging gun to your electric car.
- Start the charging process.
F) Change the key (password) of the Wallbox
3. Tap on the password/key modification.
4. Enter the new password.
1. Confirm the change.
G) Scheduling the charging process
- Activate time-controlled charging.
- Set the desired time.
- Start the charging process.
- Confirm that charging is to take place at a specific time.
LED status
Error codes and suggested solutions
Safety and warning instructions
Attention high voltage! The input and output voltage of the Wallbox is life-threatening!
- The Wallbox may only be disassembled, repaired, opened and installed by authorized and qualified personnel. Authorized and qualified personnel are persons who have certified skills and knowledge regarding the installation and operation of this type of electrical equipment and have received appropriate safety training.
- The manufacturer assumes no liability for consequences resulting from unqualified and/or improper use and/or installation.
- When installing a Wallbox, all local, regional and national regulations and laws must be observed.
- The Wallbox must not be installed and operated in the vicinity of explosive or flammable materials or in the vicinity of chemicals, vapors and other hazardous substances and objects.
- Children must be kept away from the Wallbox and accessories.
- The technical design of the Wallbox complies with protection class IP54. Nevertheless, care should be taken to ensure that it is not exposed to direct rain and severe weather.
- The charging connection of the Wallbox must always be clean and dry. Cleaning may only be carried out with a dry cloth.
- The base core must not be touched when switching on. Danger to life!
- Hybrid vehicles may only be charged when the engine is off.
- The vehicle must not be moved during the charging process.
- In case of a defect, cracks, strong abrasion, leakage and/or peculiar odors as well as unexpected behavior, the Wallbox must not be used. If such a case occurs, authorized and qualified personnel must be notified/called. The output and input power supply must be disconnected immediately.
- The Wallbox may only be disposed of via a suitable facility for recycling electrical equipment. Further information can be obtained from the local municipal administration.
Technical specification
Housing dimensions
Scope of delivery
Installation
Required tools and materials
Mounting / installation
A) Residual current circuit breaker
400V~ GB / T10963.1 / IEC60898-1, TGB1N-63 C40
B) Location / protection elements
- When selecting a location for the Wallbox, ensure that it can be properly used, maintained and repaired.
- The relevant lines, switches and fuses of the building‘s power supply must be equipped with the necessary protective elements.
C) Mounting / installation
-
Depending on the substrate, a percussion drill may need to be used.
-
Dowels must be firmly and securely anchored in the masonry.
-
Wallbox mounting with appropriate screws.
-
A cable with a thickness of 5 × 4mm² (11KW) must be used for the connection to the input port of the Wallbox. From left to right, R S T N and GND.
-
Fixing the gun holder / cable holder.
-
Lock cover, start test.
PATONA International S.L.U.
Untere Giesswiesen 17, 78247 Hilzingen, Germany
Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>