Euromaid INLCP92BGRCPACK 90cm Black Glass Wall Canopy with Roof Cavity Motor User Manual

: June 6, 2024
: Euromaid

Euromaid INLCP92BGRCPACK 90cm Black Glass Wall Canopy with Roof Cavity Motor

SAFETY INSTRUCTIONS

This manual explains the proper installation and use of your Rangehood, please read itcarefully before using even if you are familiar with the product. The manual should be keptin a safe place for future reference.
These instructions shall also be available in an alternative format, e.g. on a website or on request from the user in spec sheet format.

Things not to do:

Do not try to use the Rangehood without the grease filters or if the filters are excessively greasy!
Do not install above a cooker with a high level grill.
Do not leave frying pans unattended during use because overheated fats or oils might catch fire.
Never leave naked flames under the Rangehood.
If the Rangehood is damaged, do not attempt to use.
Do not flambe under the Rangehood.
CAUTION: Accessible parts may become hot when used with cooking appliances. The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the Rangehood. (When the Rangehood is located above a gas appliance, this distance shall be at least 75 cm)
The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.

Things to always do:

Important! Always switch off the electricity supply at the mains during installation and maintenance such as light bulb replacement.
The Rangehood must be installed in accordance with the installation instructions and all measurements
followed.
All installation work must be carried out by a competent person or qualified electrician.
Please dispose of the packing material carefully. Children are vulnerable to it.
Pay attention to the sharp edges inside the Rangehood especially during installation and cleaning.
When the Rangehood is located above a gas appliance, the minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the Rangehood that distance must be:
Gas cookers: 75 cm
Electric cookers: 65 cm
Coal or oil cookers: 75 cm
Make sure the ducting has no bends sharper than 90 degrees as this will reduce the efficiency of the Rangehood.
Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards
Warning: Before obtaining access to terminals, all supply circuits must be disconnected.

Things to always do:

Always put lids on pots and pans when cooking on a gas cooker.
When in extraction mode, air in the room is being removed by the Rangehood. Please make sure that proper ventilation measures are being observed. The Rangehood removes odours from room but not steam.
Rangehood is for domestic use only.
If the supply cord is damaged, it mustbe replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
This appliance is not intended foruse by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Warning: Before obtaining access to terminals, all supply circuits must be disconnected.

Things to always do:

Caution: The appliance and its accessible parts can become hot during operation. Be careful to avoid touching the heating elements.
Children younger than 8 years old should stay away unless they are under permanent supervision.
There shall be adequate ventilation of the room when the Rangehood is used at the same time as appliances burning gas or other fuels.
There is a fire risk if cleaning is not carried out in accordance with the instructions
Regulations concerning the discharge of air have to be fulfilled.
Clean your appliance periodically by following the method given in the chapter MAINTENANCE.
For safety reason, please use only the same size of fixing or mounting screw which are recommended in this instruction manual.
Regarding the details about the method and frequency of cleaning, please refer to maintenance and cleaning section in the instruction manual.
Cleaning and user maintenance shall not be made by children without supervision.
When the Rangehood and appliances supplied with energy other than electricity are simultaneously in operation, the negative pressure in the room must not exceed 4 Pa ( 4 x 1 0-5 bar).
WARNING: Danger of fire: do not store items on the cooking surfaces.
A steam cleaner is not to be used.
NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.

IMPORTANT INFORMATION

Points to consider for installation

Before installation, please ensure the area is clean to avoid suction of the
remaining bits of debris and dust.
Please ensure that the fan motor is firmly secured to either a flat surface such as an MDF panel affixed across the ceiling rafters, or fixed to the ceiling rafters themselves. Ensure the fan motor is level and there is no vibration when in use.
The location of the fan unit shall allow access for maintenance and repair. Permanent fixed means of access is required where the fan unit location is
beyond the extent of normal steps or ladders.
After installation, make sure that the main body is level to avoid grease
collection at one end.
Please note the dimensions of the fan motor for installation purposes.
The fan motor should be secured using the supplied brackets and screws.

INSTALLATION – ROOF CAVITY MOTOR VERSION

Schematic diagram

Connect the Rangehood main body with the external cabinet by control wire, to achieve power on and off, and also speed switching.
The control wire is separated into 3 parts, the first two parts are fixed onto the main body and external cabinet, while the middle part is extension wire.
The Rangehood main body and the external cabinet will exhaust the smoke to outdoor after installing the expansion pipe.

MOUNTING OF THE V-FLAP

If the Rangehood does not have an assembled V-flap 1, you should mount the halfparts to its body. The images only show an example of how to mount the V-flap, the outlet may be various according to different models and configuration.
To mount the V-flap 1 you should:

Mount two half-parts 2 into the body 6
a pin 3 should be top oriented;
the axis 4 should be inserted in the holes 5 on body;
repeat all the operations for the 2nd half-part

INSTALLATION

If you have an outlet to the outside, your Rangehood can be connected as below picture by means of an extraction duct (enamel, aluminium, flexible pipe or nonflammable material with an interior diameter of 220mm)

Before installation, turn the unit off and unplug it from the outlet.
The Rangehood should be placed at a distance of 65~ 75cm above the cooking surface for best effect.
Install the hook on a suitable place once the installation height is fixed, and keep it in line. The fixed position of the inside chimney bracket is the place of chimney. See pic 2.
1. Equip the outlet connecting cover onto the cabinet top, and screw 6 pcs 4*8mm screws to fix it.

Install the outlet seal ring and outlet, and fix them with 8 pcs 4*14mm screws, see pic 3. Then hang the hood on the hook. See pic 4.

Fix the outside chimney bracket on the outside chimney by 2 pcs 4*8mm screws, and be sure that the inside chimney can be adjusted the height in it freely, put the chimneys onto the Rangehood. See pic 5.
Equip the chimneys, fix the outside chimney bracket with 2 pcs 440mm screws, and use 2 pcs 430mm screws to fix the hood body. See pic 6.
Unscrew the 8 pcs ST4*14mm screws, and dismantle the outlet mesh cover, see pic 7. Note: There is no need to unscrew the 4 screws showing on pic 8.
Install the outlet seal ring and outlet, using the 8 pcs ST4*14mm screws in step 7 to fix them. See pic 9.
Install case installation bracket, and fix with 4 pcs M4 screws, spring washers and gaskets. See pic 10.
Screw 4 pcs 4*30mm screws to fix the external cabinet onto the ceiling. See pic 11 & 12.
Install the expansion pipe and fix it with cable tie. See pic 13.
Equip the expansion pipe to the outlet, and fix with cable tie. Lead one end of the expansion pipe which install on the external cabinet outlet to the outside. Both end of the motor extension wire should connect with the external cabinet control wire and the control wire of the main body top. The plastic base of the control wire should be plugged to the bottom, and make the buckle to tight status. See pic 14.

Note: You need to loosen the connecting wire before repair, follow the steps as below:
a. Rotate the lock catch of the connecting wire following the arrow direction.
b. Pull out the connector.
Adjust the height of the inside chimney to the position of the inside chimney bracket and fix on it by 2 pcs ST4*8mm screws. See pic 15.
Installation is finished. See Pic 16.

HINTS FOR EXHAUST DUCT INSTALLATION

The following rules must be strictly followed to obtain optimal air extraction:

Keep expansion pipe short and straight.
Do not reduce the size or restrict expansion pipe.
When using expansion pipe always install the pipe pulled taut to minimize pressure loss.
Failure to observe these basic instructions will reduce the performance and increase noise levels of the Rangehood.
Any installation work must be carried out by a qualified electrician or competent person.

INSTALLATION – EXTERNAL WALL HUNG MOTOR VERSION

Schematic diagram

Connect the Rangehood main body with the external cabinet by control wire, to achieve power on and off, and also speed switching.
The control wire is separated into 3 parts, the first two parts are fixed onto the main body and external cabinet, while the middle part is extension wire.
The Rangehood main body and the external cabinet will exhaust the smoke to outdoor after installing the expansion pipe.

MOUNTING OF THE V-FLAP

If the Rangehood does not have an assembled V-flap 1, you should mount the halfparts to its body. The images only show an example of how to mount the V-flap, the outlet may be various according to different models and configuration.
To mount the V-flap 1 you should:

Mount two half-parts 2 into the body 6
a pin 3 should be top oriented;
the axis 4 should be inserted in the holes 5 on body;
repeat all the operations for the 2nd half-part

INSTALLATION

If you have an outlet to the outside, your Rangehood can be connected as below picture by means of an extraction duct (enamel, aluminium, flexible pipe or nonflammable material with an interior diameter of 220mm)

Before installation, turn the unit off and unplug it from the outlet.
The Rangehood should be placed at a distance of 65~ 75cm above the cooking surface for best effect.
Install the hook on a suitable place once the installation height is fixed, and keep it in line. The fixed position of the inside chimney bracket is the place of chimney. See pic 2.
1. Equip the outlet connecting cover onto the cabinet top, and screw 6 pcs 4*8mm screws to fix it.

Install the outlet seal ring and outlet, and fix them with 8 pcs 4*14mm screws, see pic 3. Then hang the hood on the hook. See pic 4.

Fix the outside chimney bracket on the outside chimney by 2 pcs 4*8mm screws, and be sure that the inside chimney can be adjusted the height in it freely, put the chimneys onto the Rangehood. See pic 5.
Equip the chimneys, fix the outside chimney bracket with 2 pcs 440mm screws, and use 2 pcs 430mm screws to fix the hood body. See pic 6.
Install the wall mounted bracket, and fix with 4 pcs M4 screws, spring washers and gaskets. See pic 7.
Equip the expansion pipe, and use stainless steel hoop to fix it. See pic 8.
Make a cp220mm hole on the wall, and let the expansion pipe and motor connecting wire to across the wall together. Screw 4 pcs wall plugs into the wall, and then fix the cabinet on the wall with 4 pcs 4*30mm screws. See pic 9.
Install the expansion pipe onto the main body outlet and fix it with cable tie.
Connect the motor extension wire both end with the external cabinet control wire and main body top control wire. The plastic base of the control wire should be plugged to the bottom, and make the bucket to tight status. See pic
Note: You need to loosen the connecting wire before repair, follow the steps as below:
c. Rotate the lock catch of the connecting wire following the arrow direction.
d. Pull out the connector.
Adjust the height of the inside chimney to the position of the inside chimney bracket and fix on it by 2 pcs ST 4 *8mm screws. See pic 11.
Installation is finished. See Pic 12.

HINTS FOR EXHAUST DUCT INSTALLATION

The following rules must be strictly followed to obtain optimal air extraction:

Keep expansion pipe short and straight.
Do not reduce the size or restrict expansion pipe.
W.hen using expansion pipe always install the pipe pulled taut to minimize pressure loss.
Failure to observe these basic instructions will reduce the performance and increase noise levels of the Rangehood.
Any installation work must be carried out by a qualified electrician or competent person.
Do not connect the ducting system of the hood to any existing ventilation system which is being used for any other appliance, such as warmer tube, gas tube, hot wind tube.
The angle of the bend of the expansion pipe should not be less than 120°; you must direct the pipe horizontally, or, alternatively, the pipe should go up from the initial point and should be led to an outer wall.
Ensure the expansion pipe selected for installation complies with relevant standards and is fire retardant.

Start Using Your Rangehood

LED touch control

Press the “Power” button, the button controls the “on” & “off’ of the hood.
Press the button “Speed” time after time, the motor runs as low /mid / high / low /mid … , the speed runs circularly; and the LED display will indicate as 1-2-3-1-2 … circularly.
Press “Light” button, the light is on, press this button again, the light is off. Please note the Lamp is not under control of the on/off button.
When the hood is working, if press the “Timer” button, the hood will go into the status of acquiescent working (acquiescent time is 9mins), and then, LED display will be shown 9.8.7.6 … decreasing by 1, when time is up, the hood will be off automatically and the lamp will extinguish. If pressing “Timer” button, the hood will go in or go out “Timer” function.

TROUBLESHOOTING

Fault

| Possible Cause|

Solution

---|---|---
Light on, but motor does not work| Fan switch turned off| Select a fan switch position.
Fan switch failed| Contact service centre.
Motor failed| Contact service centre.
Light does not work, motor does not work| House fuses blown| Reset/Replace fuses.
Power cord loose or disconnected| Refit cord to power outlet. Switch power outlet on.
Lights not working Insufficient suction| Broken/Faulty globes| Replace globes as per this instruction.
The distance between the Rangehood and the gas top is too far| Refit the Rangehood to the correct distance.
The Rangehood inclines| The fixing screw not tight enough| Tighten the hanging screw and make it horizontal.

NOTE
Any electrical repairs to this appliance must conform to your local, state and fil federal laws. Please contact the service centre if in any doubt before undertaking any of the above. Always disconnect the unit from the power source when opening the unit.

MAINTENANCE AND CLEANING

Caution:

Before maintenance or cleaning is carried out, the Rangehood should be disconnected from the main power supply. Ensure that the Rangehood is switched off at the wall socket and the plug removed.
External surfaces are susceptible to scratches and abrasions, so please follow the cleaning instructions to ensure the best possible result is achieved without damage.

GENERAL

Cleaning and maintenance should be carried out with the appliance cold especially when cleaning. Avoid leaving alkaline or acid substances (lemon juice, vinegar etc.) on the surfaces.

STAINLESS STEEL

The stainless steel must be cleaned regularly (e.g. Weekly) to ensure long life
expectancy. Dry with a clean soft cloth. A specialised stainless steel cleaning fluid may be used.

NOTE:
Ensure that wiping is done along with the grain of the stainless steel to prevent any unsightly crisscross scratching patterns from appearing.

CONTROL PANEL SURFACE

The inlay control panel can be cleaned using warm soapy water. Ensure the cloth is clean and well wrung before cleaning. Use a dry soft cloth to remove any excess moisture left after cleaning.

Important
Using neutral detergents and avoid using harsh cleaning chemicals, strong household detergents or products containing abrasives, as this will affect the appliance appearance and potentially remove any printing of artwork on the control panel and will void manufactures’ warranty.

GREASE MESH FILTERS

The mesh filters can be cleaned by hand. Soak them for about 3 minutes in water with a grease-loosening detergent then brush it gently with a soft brush. Please do not apply too much pressure, avoid to damage it. (Leave to dry naturally out of direct sun light) Filters should be washed separately to crockery and kitchen utensils. it is advisable not to use rinse aid.

INSTALLING GREASE MESH FILTERS

– To install filters for the following four steps.
– Angle the filter into slots at the back of the hood.
– Push the button on handle of the filter.
– Release the handle once the filter fits into a resting position.
– Repeat to install all filters.

BULB REPLACEMENT

Changing the LED light

Note:

Beore changing the lights, make sure that the appliance is plugged off.
Protect against danger when changing lights, such as wearing gloves.
Light replacement should be carried out by qualified service personnel only.
Switch the unit off and pull out the plug first.
Loose the 4 pcs 4X1 OMM screws at the back of case, and then take out the outer glass.
Loose the 2 pcs screws on the lamp bracket, and then change the LED light. See pie below.
Remove the grease filter.
Unscrew the 4pcs screws on the LED light strip bracket by cross screwdriver, dismantle the LED light strip and pull out the terminal of the light connecting wire. See pie 1. (Note: It will need to dismantle the front panel first for models cannot directly take down the light strip.)
Apply the reverse procedure to install the light strip back.
– ILCOS D code for this lamp is: DSL-7-S-650
– Max wattage: 7 W
– Voltage range: DC 12V

ENVIRONMENTAL PROTECTION

| This product is marked with the symbol on the selective sorting of waste electronic equipment. This means that this product must not be disposed of with household waste but must be supported by a system of selective collection in accordance with Directive 2012/19/EU. It will then be recycled or dismantled to minimize impacts on the environment, electrical and electronic products are potentially dangerous for the environment and human health due to the presence of hazardous substances. For more information, lease contact our local or re ional authorities
---|---

NOTE
The following shows how to reduce total environmental impact (e.g. energy use) of the cooking process).
(1) Install the Rangehood in a proper place where there is efficient ventilation.
(2) Clean the Rangehood regularly so as not to block the airway.
(3) Remember to switch off the Rangehood light after cooking.
(4) Remember to switch off the Rangehood after cooking.

INFORMATION FOR DISMANTLING

Do not dismantle the appliance in a way which is not shown in the user manual. The appliance could not be dismantled by user. At the end of life, the appliance should not be disposed of with household waste. Check with you Local Authority or retainer for recycling advice.

MANUFACTURER GUARANTEE

This warranty is provided in Australia by Glen Dimplex Australia Pty Limited ABN 69 118 275 460 (Phone number 1300 556 816) and in New Zealand by Glen Dimplex New Zealand Limited NZBN 9429000069823 (Phone number 09 274 8265) in respect of the Euromaid product.

Euromaid Express Warranty
Subject to the exclusions below, we warrant that the product will not have any electrical or mechanical breakdowns within:
a) In the case of Euromaid products used for personal, domestic or household purposes, a period of 2 years from the date the product is purchased as a brand-new product from a retailer located in Australia / New Zealand.
b) In the case of Euromaid products used for purposes other than personal, domestic or household purposes (including business or commercial use), a period of 90 days from the date the product is purchased as a brand- new product from a retailer located in Australia / New Zealand. Euromaid products are designed and intended for domestic use only; and
c) All warranty repairs must be carried out by Glen Dimplex or their nominated service agent
Note: warranty periods detailed above may vary in line with agreements with select retail and builder partners and may differ between Australia and New Zealand.
The benefits conferred by this express warranty are in addition to the Consumer Guarantees referred to in section 3 and any other statutory rights you may have under the Australian / New Zealand Consumer Law and/or other applicable laws.
Warranty exclusions
This express warranty does not apply where:
a) The product has been installed, used or operated otherwise than in accordance with the product manual or other similar documentation provided to you with the product;
b) The product requires repairs due to damage resulting from accident, misuse, incorrect installation, insect or vermin infestation, improper liquid spillage, cleaning or maintenance, unauthorised modification, use on an incorrect voltage, power surges and dips, voltage supply problems, tampering or unauthorised repairs by any persons, use of defective or incompatible accessories or exposure to abnormally corrosive conditions, events independent of human control which occurred after the goods left the control of Glen Dimplex;
c) The repair relates to the replacement of consumable parts such as fuses and bulbs or any other parts of the product which require routine replacement;
d) You are unable to provide us with reasonable proof of purchase for the product;
e) the breakdown occurs after the expiry of the express warranty period set out in section 1 or f) the product was not purchased in Australia / New Zealand as a brand-new product.
Consumer guarantees
Our goods come with guarantees that cannot be excluded under the Australian / New Zealand Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
How to make a claim
You may make a claim under this warranty through our website, contacting our customer care line or via email. Contact details for Glen Dimplex Australia and New Zealand can be found at the end of this document
To make a valid claim under this warranty, you must:
a) Lodge the claim with us as soon as possible and no later than 14 days after you first become aware of the breakdown;
b) Provide us with the product serial number;
c) Provide us with reasonable proof of purchase for the product. This can take the form of a store receipt, new home handover form or other payment receipt documentation; and
d) If required by us, provide us (or any person nominated by us) with access to the premises at which the product is located at times nominated by us (so that we can inspect the product).
Warranty claims
If you make a valid claim under this warranty and none of the exclusions set out in section 2 apply, we will, at our election, either repair the product or replace the product with a product of identical specification (or where the product is superseded or no longer in stock, with a product of as close a specification as possible).
Goods presented for repair may be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the goods. Products are designed and supplied for normal domestic use. We will not be liable to you under this warranty for business loss or damage of any kind whatsoever.

Glen Dimplex Australia Pty Ltd

www.glendimplex.com.au

Australia
Ph: 1300 556 816
customer.care.ha@glendimplex.com.au

Glen Dimplex New Zealand Ltd
www.glendimplex.co.nz

New Zealand
Ph: 09 274 8265
nztechserv@glendimplex.co.nz

READ THE INSTRUCTION BOOKLET BEFORE INSTALLING AND USING THE APPLIANCE.

The manufacturer will not be responsible for any damage to property or to persons caused by incorrect installation or improper use of the appliance. The manufacturer is not responsible for any inaccuracies, due to printing or transcription errors, contained in this manual. In addition, the appearance of the figures reported is also purely indicative.

The manufacturer reserves the right to make changes to its products when considered necessary and useful, without affecting the essential safety and operating characteristics. Glen Dimplex constantly seeks ways to improve the specifications and designs of their products. Whilst every effort is made to produce up to date literature, this document should not be regarded as an infallible guide. Actual product only should be used to derive cut out sizes.

All appliances must be installed by a qualified person/s with adherence to the relevant electrical, plumbing and building codes, with compliance being issued as required by state or national legislation.

Additionally, all upright cookers must have the anti-tilt device installed correctly in adherence to the relevant standards by a licenced installer.
For maximum effectiveness and efficiency all rangehoods should be installed with the use of ductwork, by a licenced installer with adherence to the relevant state and national building codes and regulations.

All Glen Dimplex appliances are for Domestic use only, and must be installed by a licence installer into Domestic Applications only, without exception and to the required Authorities guidelines. Any installation outside of this will VOID warranty. Alfresco areas are not a Domestic application.

Distributed by:

Glen Dimplex Australia Pty Ltd
www.glendimplex.com.au

Glen Dimplex New Zealand Ltd
www.glendimplex.co.nz

For service advice, please contact the Customer Care Centre by phone or email below.

Australia
Ph: 1300 556 816
customer.care.ha@glendimplex.com.au

New Zealand
Ph: 09 274 8265
nztechserv@glendimplex.co.nz