MAGNUSSON 3663602850793 3m Self-Levelling Laser Level Instruction Manual

: June 6, 2024
: MAGNUSSON

Table of Contents

Before you start
- General laser safety warnings
- To install batteries
Functions and settings
- Laser line operation
- Laser point operation
Troubleshooting
Cleaning
Technical data
Commercial guarantee
Recycling and disposal
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

3663602850793

These instructions are for your safety. Please read them thoroughly before use and retain for future reference.

Product Description

1. LINE/OFF/POINT switch.
2. Outlet for laser line.
3. Outlet for laser point b
4. Horizontal spirit level.
5. Vertical spirit level.
6. Supporting points.
7. Battery compartment cover.| 8. Aluminium base face.
9. Magnets.
10. Metal surface for point operation.
11. Metal surface for line operation.
12. Adjusting screw of wall holder.
13. Hanging hole.
14. M6 .35×1 .25 thread for tripod.
---|---

Use

Before you start

General laser safety warnings

**IMPORTANT:

**

Please read this instruction manual carefully before using the product, and familiarise yourself with the operation, adjustments, and functions of the various switches.
Consider and follow the safety and operating instructions in order to avoid possible risks and hazards.
Keep these instructions for future use. If the product is passed on to a third party then these instructions must be included.

WARNING! Danger of permanent eye injury!

Laser radiation! Do not stare into beam.
Class II laser product.

WARNING!

DO NOT operate the tool around children or pets, this product is not a toy and is not intended for use by children.
DO NOT remove or destroy any label appearing on this instrument.
DO NOT stare directly at the laser beam, as this can cause blindness. Only turn the laser ON when being used.
DO NOT place the tool in a position that may cause anyone to stare at the laser beam, whether intentionally or unintentionally, and ensure bystanders are aware of the dangers.
DO NOT point the laser beam emitted by the instrument at people or animals.
DO NOT point the laser onto shiny or reflective surfaces such as glass or polished metals, as this could reflect the beam back at the operator or passers by.
DO NOT attempt to modify the performance of this laser device in any way. This may result in a dangerous exposure to laser radiation.

CAUTION!

DO NOT attempt to repair or disassemble the laser-measuring tool. If unqualified persons attempt to repair this product, serious injury may occur. Any repair required on this laser product should be performed only by qualified service personnel.
DO NOT operate the tool in explosive environments, such as in the presence of flammable liquids, gases or dusts. Sparks can be created in the tool which may ignite the dust or fumes.
ALWAYS turn off the instrument whenever it is not in use. Failure to do so will increase the possibility of someone inadvertently looking directly at the laser beam.
DO NOT use optical instruments with this product, as this will increase risk of injury to the eyes.
DO NOT use laser viewing glasses as safety goggles, as they do not protect the eyes against laser radiation.
DO NOT use parts or accessories that have been designed for use with other laser tools, as this could result in serious injury or loss of performance.
The accuracy or performance of the instrument may be reduced if it is used beyond it’s designed range, or in strong lighting conditions.
DO NOT expose the product to shock, continuous vibration or extreme hot or cold temperatures, as this could damage the tool and/or cause serious injury to the user.
ALWAYS handle the laser product with care. Treat it as you would any other optical device such as a camera or binoculars, and DO NOT touch the lens directly.

To install batteries

This instrument requires 2 x 1.5V AAA/LR03 batteries (not included).
Remove the battery compartment cover.
Insert the batteries paying attention to the polarity (+/-) marked on the compartment and batteries.
Close the battery compartment cover.

SAAM10586 Line and Point laser level A5 V6R.indd 5

CAUTION!

ALWAYS turn off the instrument before replacing the batteries.
ALWAYS remove the batteries if the instrument is not to be used for extended periods.
ALWAYS use high quality batteries of the same brand, type and age.
If the instrument does not work properly, or the low battery icon is displayed, replace the batteries immediately.
DO NOT expose the batteries or instrument to extreme temperatures or direct heat source, as this can cause the batteries to leak.
If the batteries should leak, remove them using a cloth and dispose of them according to local regulations. Clean any leaked battery acid avoiding any contact with skin, eyes & mouth.
If any contact does occur, rinse affected areas immediately with fresh water and seek medical advice.

Functions and settings

Laser line operation

Switch on laser “LINE” using switch 1.
Hold level against wall,using multi-function base
Ensure it is level using horizontal (4) or vertical (5) spirit bubbles as required.

Laser point operation

A tripod offers a stable, height-adjustable measuring support.
The multi-function base has a standard M6.35×1.25 thread for attaching to a tripod (not included) (Fig. 3). This is ideal for levelling kitchen cabinets, counter tops, window framing, and so on.
Rotate the upper part of the base, instead of the meter, to project the laser point to the desired points on different surfaces to check if the points are at the same height (Fig. 2a). Ensure to check if the bubble inside the horizontal spirit level is centred.

Troubleshooting

Problem	Possible cause	Solution
Meter cannot start.	Batteries incorrectly inserted. Low battery.	Re-insert

batteries correctly or replace with new batteries.
Laser line hard to see.| Light in area is too bright.| Use in dimmer area.
Laser line not level.| Level bubbles not properly aligned. Meter is mounted on an uneven base.| Make sure level bubbles are centered.
Make sure leveling bubbles are level after mounting.
Laser line is horizontal while a vertical line is desired.| Laser meter is in the incorrect position.| Turn the meter 90° to the vertical orientation.

Cleaning

To ensure the instrument operates at optimal performance it should be regularly cleaned.

ALWAYS switch the instrument OFF before cleaning.
The housing can be cleaned with a damp cloth, taking care that no water enters the product.
DO NOT immerse the electrical/optical parts of the product in water or other liquids, and never hold it under running water.
Any lenses can be cleaned using a cotton bud with a small amount of distilled water or alcohol.
After cleaning, ensure that all parts dry properly before use.
The product should be stored carefully, so that it is protected from dust and scratches.

Technical data

COMPONENT	SPECIFICATION
Laser	A=635nm (Laser line) and 650nm (Laser point), Class II laser, maximum

Commercial guarantee

At Magnusson we take special care to select high quality materials and use manufacturing techniques that allow us to create ranges of products incorporating design and durability. That’s why we offer a 5 year guarantee against manufacturing defects on our Rotary laser level.
This product is guaranteed for 5 years from the date of purchase, if bought in store, or delivery, if bought online, for normal (nonprofessional or commercial) household use. You may only make a claim under this guarantee upon presentation of your sales receipt or purchase invoice. Please keep your proof of purchase in a safe place.
The guarantee covers product failures and malfunctions provided the Rotary laser level was used for the purpose for which it is intended and subject to installation, cleaning, care and maintenance in accordance with standard practice and with the information contained above and in the user manual. This guarantee does not cover defects and damage caused by normal wear and tear of the Rotary laser level and damage that could be the result of improper use, faulty installation or assembly, neglect, accident modification of the product. The guarantee is limited to parts recognised as defective. It does not, in any case, cover ancillary costs (movement, labour) and direct and indirect damage.
If the Rotary laser level is defective during the guarantee period, then we reserve the right, at our discretion, to replace the defective Rotary laser level with a product of equivalent quality and functionality or to provide a refund.

This guarantee only applies to the country of purchase or delivery and is not transferrable to any other countries. This guarantee is non-transferrable to any other person or product. Relevant local law will apply to this guarantee. This guarantee is in addition to and does not affect your statutory rights relating to faulty goods as a consumer.
Guarantee related queries should be addressed to a store affiliated with the distributor you purchased the Rotary laser level from.

Distributor: B&Q plc, Chandlers Ford, Hants, SO53 3LE United Kingdom www.diy.com
SFD Limited, Trade House, Mead Avenue, Yeovil, BA22 8RT, United Kingdom www.screwfix.com

Recycling and disposal

Environmental protection: Discarded electrical products are recyclable and should not be discarded with the domestic waste.
Please recycle where facilities exist, or check with your local authority or local store for recycling advice.

| This product complies with conformity requirements of the applicable European Regulations or Directives.| yyWxx| Laser Radiation Manufacturing date code; year of manufacturing (yy) and week of manufacturing (Wxx).
---|---|---|---
| disposed of with house hold waste. Please
recycle where facilities exist check with your| | Laser Radiation
| Waste electrical products should not be disposed of with house hold waste. Please recycle where facilities exist check with your
local authority or local store for recycling advice.| | Class 2 Laser Product
| (yy) and week of manufacturing (Wxx). It meets all the required technical regulations of the Customs Union of the Eurasian Economic Community.| | Do Not Stare Into The Beam

Manufacturer
UK Manufacturer:
Kingfisher International Products Limited,
3 Sheldon Square, London, W2 6PX,
United Kingdom

EU Manufacturer:
Kingfisher International Products B.V.
Rapenburgerstraat 175E
1011 VM Amsterdam
The Netherlands
www.kingfisher.com/products
www.diy.com
www.screwfix.com
www.screwfix.ie
To view instruction manuals online, visit www.kingfisher.com/products

SAAM10586 Line and Point laser level A5 V6R.indd
03/12/2020 15:34