ITALIAN STAGE IS SPX08AUB Professional Multimedia Loudspeaker System User Manual

ITALIAN STAGE IS SPX08AUB Professional Multimedia Loudspeaker System User

Manual

INTRODUCTION

Thank you for your purchase of the ITALIAN STAGE IS SPX08AUB – IS SPX10AUB. We hope that you will enjoy the use of the ITALIAN STAGE Speakers. Please read carefully through this manual before beginning to use, so that you will be able to take full advantage of the IS SPX08AUB – IS SPX10AUB features and enjoy trouble-free operation for years to come. Please keep this manual at a safe and dry place where you easily can access it.

CAUTION: Before switching on the instrument or device read carefully the safety instructions to avoid serious injuries or damage of the product. Operators manual.

PRECAUTIONS

Please read carefully before proceeding
Warning: Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from: electrical shock, short- circuiting, damages, fire or other hazards. These precautions in-clude, but are not limited to, the following:
Power supply / power cord (devices with power cords/power supplies)

• Only use the voltage specified as correct for the device. The required voltage is printed on the type plate of the device. Check the power cable from time to time regarding dirt, damage or other influ-ence.
• Use only the included power cord / power supply or adaptor. Do not place the power chord near heat sources such as: heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it.
• Remove the electric plug from the outlet when the device is not to be used for extended periods of time, or during electrical storms. When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it.
• To avoid generating unwanted noise, make sure there is adequate distance (50 cm or more) be-tween the AC power adaptor and the device. Do not cover or wrap the AC power adaptor with a cloth or blanket.

Location

• When setting up the device, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet.
• Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire.
• Do not expose the device to excessive dust or vibrations, or extreme cold or heat (such as: in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components.
• Do not place the device in an unstable position where it might accidentally fall over.
• Do not block the vents. This device has ventilation holes at the bottom/rear to prevent the internal temperature from becoming too high. In particular do not place the device on its side or upside down.
• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Doing so may result in noise, both in the device itself and in the TV or radio next to it.

Connections and handling

• Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum.
• Do not use the device or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician.
• Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on the buttons, switches or connectors

Battery-powered devices

• In the event that the device is not used for prolonged periods of time, however, it is advisable to periodically perform some charge / discharge cycles of the battery, to prolong the life of the battery.

Do not open

• Do not open the device or attempt to disassemble the internal parts or modify them in any way. The device contains no user-servicable parts. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified service personnel.

Water warning

• Do not expose the device to rain, use it near water or in damp or wet conditions on it containing liquids that might spill into any openings. Never insert or remove an electric plug with wet hands.

If you notice any abnormality

• If the power cord or plug becomes frayed or damaged, or if there is a sudden loss of sound during use of the device, or if any unusual smells or smoke should appear to be caused by it, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device in-spected by qualified service personnel.

GETTING STARTED

Installation
Place the speaker on a solid flat surface (table, ground, etc.) or use a solid speaker stand with 35mm flange. Make sure that all fixings are tight.

Power connection and wiring
Please connect the power cable to 110/220 (230) V 50/60Hz power voltage. Make sure to set the power input selector to the available net voltage. Connect all input/output signals with XLR and/or 6.3 mm jack cables. Do not connect multiple inputs possibilities (ex. RCA/ Jack 6,3 mm) with more than one cable. After you finished all audio connections set the master volume (if available) to “0”. Switch on the audio source and speaker power. Set Mic/Line level to 12 o’clock position and increase master volume to a comfortable level.

CONTROL PANEL

Multimedia section

• SD
  In this socket, you can insert an SD memory card containing audio files.

• USB
  In this socket you can insert an USB drive containing audio files.

• BT LINK
  This button allows you to pair two speakers so that you can send stereo signals from your Blue-tooth device.

• MODE
  Push this button to select the audio source from SD, USB or Bluetooth external devices.

• Play/Pause
  This button plays or pauses the current audio file.

• Song repeat
  It repeats the current song.

• Previous song
  Skip to previous song.

• Next song
  Skip to the next song.

• Microphone Input
  Allows you to connect a microphone with XLR or 6.3 mm Jack.

• Microphone Volume control
  Use this control to set the volume level of mi-crophone.

• Line Input
  Allows you to connect an external audio de-vice (CD, radio / DVD, etc.). with XLR, 6.3 mm Jack or RCA plugs.

• Line Input Volume control
  Use this control to set the volume level of Line-In Signal.

• Signal Output
  Use 6.3 mm Jack to connect another powered speaker.

• Treble
  Use it to set the high frequency level.

• LIMIT LED

• POWER LED

• Bass
  Use it to set the low frequency level.

• LABEL
  Serial number and electrical characteristics.

• ON/OFF Power Switch
  Press to power on/off the speaker box.

• AC Power
  Use it to connect the Ac power cord.

REMOTE CONTROL

Media player and remote-control functioning depend on the source or audio file types. Some Keys are operating or not depending on SD, USB memory or Bluetooth audio source.

PLAY PAUSE: This button plays or stops the current song.

EQ: Use this option to set a sound EQ for audio files reproduction: Rock, Pop, Classical, Jazz, Blues, Hall, Bass, Soft, Country, Opera, Norma.

VOLUME low/high: Use these keys to move the sound volume up or down.

0/9: Skip to a specific song number. All songs are sorted in numeric and alphabetical order. Select a number to play the corresponding song.

100+/200+: Use these keys to skip up to 100 or 200 song numbers.

PREVIOUS/NEXT: Use these keys to jump to the next or previous song.
STOP: Use this key to stop the current song reproduction.

MUTE: Use this key to select the audio source from USB FLASH DRIVE, SD MEMORY CARD, BLUE-TOOTH DEVICE.

MUTE: Use this key to mute the audio on the current song.

CONNECTIONS

XLR CONNECTIONS

BALANCED WIRING

1. GROUND, SHIELDING
2. NEGATIVE SIGNAL (-)
3. POSITIVE SIGNAL (+)

UNBALANCED WIRING

1. GROUND, SHIELDING
2. BRIDGED TO PIN 1
3. POSITIVE SIGNAL (+)

JACK 6.3 mm CONNECTIONS

CONFIGURATIONS

**

**

SPECIFICHE TECNICHE TECHNICAL SPECIFICATIONS

Remote Control
HF DIAPHRAM| 1″Driver| 1″Driver
LF CONE| 8“| 10“
LF VOICE COIL| 1,5“VC| 1,5“VC
LINE OUTPUT| XLR OUT + Jack 6,3 mm| XLR OUT + Jack 6,3 mm
LINE INPUT| XLR IN + Jack 6,3 mm

+ 2 x RCA

| XLR IN + Jack 6,3 mm

+ 2 x RCA

MIC INPUT| XLR IN + Jack 6,3 mm| XLR IN + Jack 6,3 mm
RMS POWER| AB class 120 + 30 W| AB class 120 + 30 W
PEAK POWER| 300 W| 300 W
FREQUENCY RESPONSE| 60hz-20khz| 55hz-20khz
PEAK SPL| 123 dB| 125 dB
DIMENSIONS| 25x40x20 cm (WxHxD)| 30x46x27 cm (WxHxD)
WEIGHT| 6 Kg| 7.5 Kg

CONFORMITY

Products are designed and manufactured with high-quality materials and components, which are recyclable and can be reused. The symbol means that your product should be disposed of separately from household waste when it reaches end of life. Please dispose of this equipment at your local collection point or recycling center. All specifications and designs are subject to change without notice. All information was correct at time of printing. ITALIAN STAGE does not guarantee for the accuracy or completeness of any description, photo or statement contained in this manual. Printed colors and specifications may slightly vary from product. Products from ITALIAN STAGE are only sold through authorized dealers. This manual is protected by copyright. Any copying or printing is only allowed with the written consent of the ITALIAN STAGE. The same applies to the reproduction or copying of images.

References

• Italian Stage | Italian Stage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>