Shelly PRO 4PM 4-Channel DIN Rail Relay Switch User Guide
- June 6, 2024
- Shelly
Table of Contents
Shelly PRO 4PM 4-Channel DIN Rail Relay Switch
Read before use
This document contains important technical and safety information about the
device, its safety use and instal-lation.
CAUTION! Before beginning the installation, please read this guide and any other documents accompanying the device carefully and completely. Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of the law or refusal of legal and/or commercial guarantee (if any). Allterco Robot-ics is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure of following the user and safety instructions in this guide.
Product Introduction
Shelly® is a line of innovative Devices, which allow re-mote control of
electric appliances through a mobile phone, tablet, PC, or home automation
system. Shelly® may work standalone on the local Wi-Fi network, without being
managed by a home automation controller, or it can also work through cloud
home automation services. Shelly® devices can be accessed, controlled, and
monitored remotely from any place the User has an Internet connectivity, as
long as the devices are connected to a Wi-Fi router and the Internet.
Shelly® has an integrated web server, through which the User may adjust,
control and monitor the Device. Shelly® has two Wi-Fi modes – access Point
(AP) and Client mode (CM). To operate in Client Mode, a Wi-Fi router must be
located within the range of the Device. Shelly® devic-es can communicate
directly with other Wi-Fi devices through HTTPS protocol. An API can be
provided by the Manufacturer. Shelly® devices may be available for monitor and
control even if the User is outside the range of the local Wi-Fi network, as
long as the Wi-Fi router is connected to the Internet. The cloud function
could be used, which is activated through the web server of the Device or
through the settings in the Shelly Cloud mobile application. The User can
register and access Shelly Cloud, using ei-ther Android or iOS mobile
applications, or any internet browser and the website:
https://my.Shelly.cloud/
Control your home with your voice
Shelly® devices are compatible with Amazon Echo and Google Home supported
functionalities. Please see our step-by-step guide on:
https://shelly.cloud/support/compatibility/
Shelly® Pro Series
Shelly® Pro series is a line of Devices suitable for homes, offices, retail
stores, manufacturing facilities, and other buildings. Shelly® Pro devices are
DIN mountable inside the breaker box, and highly suitable for new building
con-struction. Connectivity for all Shelly® Pro devices can be through Wi-Fi
or LAN Internet connection, and Bluetooth can be used for the inclusion
process. Shelly® Pro series offers PM-products for real-time precise power
measurement.
LEGEND:
- N – Neutral input (Zero);
- L – Line input (110-240V);
- L* – Input of O1, O2, O3, O4;
- O1, O2, O3, O4 – Output 1, 2, 3, 4;
- S – Switch (input) for control;
- S1, S2, S3, S4 – Switch (input) controlling O1, O2, O3, O4
- LAN – Local Area Network RJ 45 connector
*The cables connected to L must be with the same lenght!
Installation Instructions
Connect the relay to the power grid and install it in the switchboard as shown in the scheme (fig. 1) and follow-ing the Safety Instructions. Before installing/mounting the device, ensure that the grid is powered off (turned down breakers) and in compliance with the Safety Norms. The Shelly Pro 4PM smart relay by Allterco Robotics is intended to be mounted into a standard switchboard on DIN rail, next to the circuit breakers in order to control and monitor the electric power through it. Shelly can work as a standalone device or as an accessory to a home auto-mation controller. Before starting, wire check that the breakers are turned off and there is no voltage on their terminals. This can be done with a phase meter or multimeter. When you are sure that there is no voltage, you can start wiring the ca-bles according to fig.1. Install a wire from O1, O2, O3, O4 – to the load and from the load to the Neutral. Install also a wire from the Fuse to L. Connect the Neutral to the device. The last step is to in-stall cables from the switches to the terminals S1, S2, S3 and S4. For inductive appliances, those that cause voltage spikes during switching on: electrical motors, as fans, vacuum cleaners and similar ones, RC snubber (0.1µF / 100Ω / 1/2W / 600V AC) should be wired between Output and Neutral of the circuit.
CAUTION!
- Do not install the device at a place that is possible to get wet.
- Danger of electrocution. Mounting/ Installa-tion of the Device to the power grid has to be performed with caution, by a qualified person (electrician).
- Danger of electrocution. Mounting the De-vice to the power grid has to be performed with caution.
- Do not allow children to play with the button/ switch connected to the Device. Keep the Devices for re-mote control of Shelly (mobile phones, tablets, PCs) away from children.
- Danger of electrocution. Even when the De-vice is turned off, it is possible to have voltage across its terminals. Every change in the connection of the terminals has to be done after ensuring all local power is powered off/disconnected.
- Do not connect the Device to appliances ex-ceeding the given max load!
- Use the Device only with a power grid and appliances which comply with all applicable regulations. A short circuit in the power grid or any appliance connected to the Device may damage the Device.
- Connect the Device only in the way shown in these instructions. Any other method could cause damage and/or injury.
RECOMMENDATION!
- Тhe Device may be connected to and may control electric circuits and appliances only if they comply with the respective standards and safety norms.
- The Device may be connected with solid single-core cables with increased heat resis- tance to insulation not less than PVC T105°C.
Initial Inclusion
You may choose if you want to use Shelly Pro 4PM with the Shelly Cloud mobile
application and Shelly Cloud ser-vice. Instructions on how to connect your
device to the Cloud and control it through the Shelly App can be found in the
“App guide”. You can also familiarize yourself with the instructions for
Management and Control through the embedded Web interface.
Specification
- Power supply: 110-240V; 50/60Hz AC
- Max current per channel: 16A
- Total max. current of all outputs: 40 A
- RF output power (WiFi) 13.83 dBm
- RF output power (Bluetooth) 4.97 dBm
- Ambient temperature: 0°C – 40°C
- Radio signal power: 1mW
- Radio protocol: Wi-Fi 802.11 b/g/n
- Frequency: 2412-2472 МHz; (Max. 2483 MHz)
- Operational range (depending on local construction):
- up to 50 m outdoors,
- up to 30 m indoors
- Dimensions (HxWxL): 57,5×53,4×90 mm
- Electrical consumption: < 4 W
- Mounting – DIN rail
- Wi-Fi – YES
- Bluetooth: v.4.2
- Basic/EDR: YES
- Bluetooth modulation: GFSK, π/4-DQPSK, 8-DPSK
- Bluetooth frequency TX/RX – 2402 – 2480MHz
- LAN – YES
- Temperature Protection – YES
- Scripting (mjs) – YES
- MQTT – YES
- CoAP – No
- URL Actions – 20
- Scheduling – 50
- Add-on support – No
- CPU – ESP32
- Flash – 8MB
Display
Home Screen – Shows the status of the circuit (on/off), current power
consumption and connection status. By pressing the “OK” button and holding it
for a few sec-onds you can go to the Menu. From there you can select with the
arrow buttons and pressing the “OK”:
- Main – pressing the “OK” button will return you to the Home screen
- Network – set on/off :
- Wi-Fi
- Ethernet (LAN)
- Bluetooth
- Status – status of the device
- Maintenance
- Wi-Fi reset
- Factory reset
- Reboot
Technical Information
- Control through Wi-Fi from a mobile phone, PC, auto-mation system or any other Device supporting HTTP and/or UDP protocol.
- Microprocessor management.
- Controlled elements: 4 electrical circuits/ appliances.
- Controlling elements: 4 relays.
Shelly may be controlled by an external button/switch.
Declaration of conformity
Hereby, Allterco Robotics EOOD declares that the radio equipment type Shelly
Pro 4PM is in compliance with Di-rective 2014/53/EU, 2014/35/EU, 2014/30/EU,
2011/65/EU. The full text of the EU declaration of conformity is available at
the following internet address
https://shelly.cloud/knowledge-base/devices/shelly-pro-4pm/
- Manufacturer: Allterco Robotics EOOD
- Address: Bulgaria, Sofia, 1407, 103 Cherni vrah Blvd.
- Tel.: +359 2 988 7435
- E-mail: support@shelly.cloud
- Web: http://www.shelly.cloud
Changes in the contact data are published by the Manu-facturer at the official website of the Device http://www.shelly.cloud All rights to trademark Shelly® and other intellectual rights associated with this Device belong to Allterco Ro-botics EOOD.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>