Johnson Suisse JTTV301.J2371 Rimless Ambulant Toilet Suite Instruction Manual
- June 6, 2024
- Johnson Suisse
Table of Contents
Johnson Suisse JTTV301.J2371 Rimless Ambulant Toilet Suite
INSTALLATION INSTRUCTIONS
Johnson Suisse Venezia Rimless FTW Suite Code JTTV301.J2371
DESCRIPTION
- The Venezia suite is a fully concealed, rimless flush-to-wall suite.
- The suite is supplied with an adjustable S Trap connector fitting that permits a 90-190mm set out range. For greater set out (190-225mm) alternative connector (Code X011B) is needed.
- The suite can also be connected in a P Trap configuration (fittings not supplied).
- The water inlet is back entry with optional bottom entry and adjustable for left or right side available.
- The cistern is bolted to the pan from inside the cistern tank and can be removed if necessary for servicing.
- The suite has a soft close seat that is attached via top-fixed bolts. The seat is removable for cleaning.
- Floor fixing brackets are provided.
INSTALLATION STEPS
-
I nspect pan, cistern and seat for any transit damage before starting installation.
-
C heck site roughing in, cistern tap position and assembly dimensions before starting installation. The WC must be installed on a level surface.
-
Place the pan in position ensuring it is aligned with the centreline of the sewer connection. Mark the location of the pan fixing bolt holes.
-
Remove pan and locate the position of the floor brackets 25mm in from the external edges of the pan side. Drill the holes (10mm) to attach the floor fixing brackets. (DIAGRAM 1)
-
For S Trap installation cut the threaded bracing prop on the pan connector elbow to the correct length to suit the set out. Cut the pan connector fitting to the correct length(265mm from wall) and height(180mm from floor) to suit the job. Install the connector and screw the bracing prop to the back wall. Check the outlet connection fit with the pan fully back against the wall.(DIAGRAM 2)
-
For P Trap installations a pan connector and extension will be required.
-
Fit the threaded cistern fixing inserts into the holes in the cistern
-
platform of the pan ( DIAGRAM 3)
-
Move the pan back into position ensuring it seals with the pan connector.
-
Fit the screws into the floor fixing brackets and affix decorative caps. A waterproof sealant may be applied to the pan base.
Note – if mortar bedding is required use a 4:1 sand and standard cement mix (do not use Rapid Hardening Cement). If the floor is tiled, cut out the tiles beneath the pan to create a good bonding surface.
-
Cistern fitting – The water supply to the inlet valve must be connected in accordance with AS/NZ3500.1.
- Flush out the supply pipes before connecting the water supply . This is particularly important in new installations.
- Fit the blanking plug provided to seal the inlet hole in the base of the cistern.
- Check that the inlet and outlet valve securing nuts are firmly tightened to prevent leaks. Do not over-tighten.
- Connect the water supply flexihose on the inlet valve to the water supply isolating valve (not supplied).
-
Fit the foam sealing ring to the outlet valve base and fit the cistern to the pan using the seals, washers and bolts provided (DIAGRAM 4). Screw down firmly and evenly to compress the foam sealing ring.
-
Fill the cistern and check the water level, if necessary adjust the inlet valve float so the water is at the indicated level.
-
Attach the cistern lid and buttons and test flush several times while checking for leaks
-
Fit seat
Note: This suite is supplied with a back entry water inlet valve as standard. A conversion valve for a bottom entry water inlet is available as an optional extra.
Scope of Use – Venezia Rimless FTW Toilet Suite
-
This toilet suite is manufactured in vitreous china and is a rimless close-coupled design. The pan and cistern are supplied as a matched set.
-
The suite is suitable for installation for general use in interior domestic or commercial applications.
-
The suite is supplied in a P Trap configuration with S Trap installation achieved using a plastic converting pan connector. This connector provides some flexibility in the possible set-out range.
The Venezia toilet suite complies with AS1172 Parts1 & 2 and has a recommended working load bearing limit of 200kg. -
The operating inlet water pressure range is 20-800kPa.
-
Installation is subject to the National Construction Code Vol.3 – Plumbing Code of Australia and associated reference Standards that may be applicable at the time.
-
To comply with the terms of the BPA warranty the product must be installed by a licensed plumber to the provided instructions.
-
External vitreous china surfaces should be cleaned with a soft, damp cloth and mild detergent.
-
The interior of the flushing bowl should be regularly cleaned with a toilet brush and proprietary toilet cleanser.
-
Chemical/chlorine water sanitizers must not be used in the cistern tank.
INLET VALVE SERVICE
-
Major water level adjustment
-
Minor water level adjustment
-
Cleaning the valve diaphragm
-
OUTLET VALVE SERVICE
Documents / Resources
|
Johnson Suisse JTTV301.J2371 Rimless Ambulant Toilet
Suite
[pdf] Instruction Manual
JTTV301.J2371 Rimless Ambulant Toilet Suite, JTTV301.J2371, Rimless Ambulant
Toilet Suite
---|---