ifi B095HKWDJD Bluetooth Decoder Instruction Manual
- June 6, 2024
- ifi
Table of Contents
ifi B095HKWDJD Bluetooth Decoder
INSTRUCTIONS
-
Power On/Off and Bluetooth format prompt Long press the power switch to power on/off the GO Blu.
Note: press the power switch twice and the voice will prompt you about the Bluetooth format you are currently receiving. -
Multi-function knob
This knob controls:- Analogue volume control (turn)
- Play/Pause (a short click)
- Skip forward (two short clicks)
- Skip back (short press three times)
- Wake up voice assistant (long press)
-
Settings and Bluetooth pairing
This button chooses between (Please refer to item 4):- Off
- XBass + space
- XBass
- Pairing (long press)
- space
-
Sound effects and Bluetooth status LED
The LED color scheme indicates the current Sound effects and Bluetooth status of GO Blu.-
LED: Mode
-
Yellow: XBass
-
Blue : space
-
Magenta : XBass + XSpace
-
Off
Bluetooth -
Blue : Wireless Bluetooth (Connected)
-
Blue (flashing) : Wireless Bluetooth (Awaiting connection)
-
Blue/Red (flashing) : Wireless Bluetooth (Pairing)
Pairing
From the switch on, the ZEN Blue will blink blue as it searches for a previously paired device. If a stored device is not found, it will automatically enter pairing mode and blink blue/red. To enter pairing mode, press the button long until Bluetooth Mode LED flashes blue/red. To pair, look for “iFi Hi-Res Audio” in the list of available Bluetooth devices on your phone. The GO Blu is able to store up to 8 paired Bluetooth devices.
-
-
Balanced 4.4mm headphone output
Connect balanced 4.4mm headphones. -
Single-ended 3.5mm headphone output
Connect single-ended 3.5mm headphones. -
Factory Reset
System reset (long press ≥3s). -
USB-C (5V) battery charge input
For charging only. It will take ~30-40 minute for a high-powered USB charger to fully charge GO Blu. Use the enclosed USB ‘Type A’ to ‘Type C’ cable, smart charger or a regular charger up to 6.3V. -
LED for Battery Status
LED Status
Green 60%
Yellow 6%
Red ≤ 6%
The battery LED will flash when it is charging -
Microphone
Built-in mic for hands-free calls when paired with your smartphone.
Specifications
Chipset: Qualcomm QCC 5100 Series
TM Input: USB-C/Bluetooth 5.0 ( AAC, SBC, aptX, aptX HD,
aptX Adaptive, aptX LL, LDAC, LHDC/HWA Codec)
Headphone Outputs:
Balanced: 4.4mm
UnBAL: 3.5mm
Power Output:
Balanced: 245mW@32Ω; 52mW@600Ω
UnBAL: 165mW@32Ω; 13mW@600Ω
Output Impedance:
Balanced: <1Ω
UnBAL: <1Ω
SNR:
Balanced: 111dBA
UnBAL: 106.5dBA
DNR: 120dB(A) (BAL/UnBAL)
THD + N:
Balanced: <0.009% (6.5mW/2.0V @ 600Ω)/
UnBAL: <0.03% (100mW/1.27V @ 16Ω)
Frequency Response: 20Hz – 45kHz (-3dB)
Battery: Lithium-polymer 450mAh approx. 12 hours
Power System: Charging via USB-C, BC V1.2 compliant up to
1000mA charging currentand 6.3 volts
Dimensions: 54 x 34 x 13 mm
2.1″ x 1.3″ x 0.5”
Weight: 27 g (0.95 oz)
Warranty period: 12 months
FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Warning: Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>