NITTOKU ITS-LRW210 Intelligent R/W Device User Manual

Intelligent R/W
MODEL: ITS-LRW210 User Manual
Ver1.1

Thank you for your purchase.
Please read this manual carefully to ensure correct use.
After reading it, please keep it in a safe place. For details, please refer to the user manual.
This product should be handled by a specialist who has knowledge of electricity.

Regulations

1. Taiwan
   Model: ITS-LRW210
   Brand: NITTOKU
   Antenna
   **| CCAJ22LP**0T3| ITS-LANT30S-1
   ITS-LANT30S-2U
   ---|---|---
   | CCAJ22LP0T3| ITS-LANT30S-3
   | CCAJ22LP***0T3| ITS-LANT30S-3U
2.  The United States

ITS-LANT30S-2U
ITS-LANT30S-3
ITS-LANT30S-3U

FCC Note
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Do not remove the ferrite core installed on the antenna cable for RF interference suppression
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Safety precautions

For safety reasons, be sure to observe the following items.

1. Please disconnect the power supply of the R/W body when loading and unloading the power supply, signal line wiring, connector, and antenna.
2. Please do not use it in places that produce flammable and explosive gases.
3. During installation, please make sure to tighten the screws (recommended torque: 0.6 N/m).
4. In order to ensure the safety of operation and maintenance, please install it away from high-voltage equipment and power equipment.
5. Please do not put foreign matters including water and metal, etc. into the gap of the box. It may cause fire and electric shock.
6. Please do not disassemble, repair or modify this product.
7. Please treat it as industrial waste when it is discarded.
8. Please pay attention to ventilation when installing.
9. Please do not install near equipment that generates a lot of heat (heater, transformer, large capacity resistor, amplifier, etc.).
10. When you feel that the product is abnormal, please stop using it immediately, turn off the power supply and contact the branch of the Company.

Precautions for use

1. Storage environment
   1. Please pay attention to the ambient temperature and humidity of the storage place during storage.

2. Installation
   1. Please avoid direct sunlight during installation.
   2. Please avoid corrosive gas, dust, metal powder, and salt during installation.
   3. Please avoid water, oil, and chemical droplets during installation.
   4. Please avoid places with large temperature changes during installation.
   5. Please install in a place with low humidity and no condensation.
   6. Please avoid places where the use temperature exceeds the specification range during installation.
   7. Please avoid the place where vibration or impact is directly transmitted to the main engine.

3. Installation
   1. This product uses a 134.2 kHz frequency band to communicate with the ID tag. Some transceivers, motors, monitoring equipment, power supplies (power IC), etc. produce radio waves (noise) that affect communication with ID tags. If you use it near equipment that may produce noise, please check the impact in advance.

4. Wiring work
   1. Do not carry out reverse connection of power terminals.
   2. Please use it at the voltage specified in this manual.
   3. Please do not use the same wiring path as a high voltage wire or a power wire.
   4. In order to prevent electrostatic damage, when contacting the signal wire inside the terminal part or connector, antistatic measures such as wrist overlap should be taken before working.
   5. When installing or disassembling the antenna, please do not apply too much load to the connector.
   6. Please use the correct antenna conforming to R/W.

5. Power supply and grounding wire
   1. The grounding terminal (frame grounding) terminal must adopt Class D grounding because the above matter will lead to performance degradation.

6. Cleaning
   1. Please use commercially available alcohol when cleaning.
   2. Because organic solvents including diluent, Benzin, benzene, acetone, etc. will peel off the resin part and coating, please do not use them.

7. Communication performance
   1. Because the communication performance will change according to the factors including metal, noise, temperature, etc. at the antenna setting place, please confirm in the actual use environment.
   2. Because the communication area will change according to the ID tag, please leave enough space when designing.

8. Screw fastening glue
   1. The screw fastening glue (screw lock) should not be used in the screw of the deteriorated resin portion with the possibility of cracking or the resin- made washer portion.

9. Communicate with the host
   1. After confirming the start of this product, please communicate with the host. In addition, please perform processing such as clearing the reception buffer of the device at the initial startup because the host interface may send out uncertain signals when starting this product.

10. Precautions for a product startup
    1. Because of the risk of product failure, please do not turn off the power supply immediately after turning on the power supply, when mode switching, or when the product is started by reset, etc.

11. Transponder
    1. This machine communicates with RI-TRP-DR2B (-30), RI-TRP-DR2B (-40), and RI-TRPWR2B (-30) produced by TI Company.
    2. Regarding the failure of the transponder, it is difficult to assume the guarantee responsibility.

Introduction

This product is a reader/writer that can read and write data of Texas Instruments (TI)-made the tag, RI-TRPDR2B (-30), RI-TRP-DR2B  (-40), and RI- TRP-WR2B (-30).

Rating value

protrusions)
Main body weight| : 197g
Adaptive antenna| ITS-LANT30S-1
ITS-LANT30S-2U
ITS-LANT30S-3
ITS-LANT30S-3U

***** In order to improve performance, this rating value is subject to change without prior notice.

Components

Please check the contents included with the product.

•  ITS LRW-210 main unit
• Power connector
• User manual

Names of the components

1. Antenna connector
2. Power lamp (power supply)
3. COMM lamp (in the communication)
4. STATUS lamp (status)
5. RS-232C connector jack| 6. DIP-SW
7. Ethernet connector jack (LAN)
8. Grounding terminal
9. Power connector jack (DC24V, RS-485)
10. M3 Mounting hole×4
---|---

Preparation

• Please insert the power connector into the main unit.
• If you want to disconnect the power connector, use a dedicated driver or equivalent and disconnect the power connector while pressing the lock button on the connector.

Installation

• Please fix the 4 positions in the special mounting holes at the backside of the main unit with M3 screws.
• Please ensure that the ground terminal is grounded to prevent malfunction and faults caused by surges.
• Please do not extend the screw over 3mm from the mounting plate to the inside of the body.
• There is the risk of damage to internal parts.

Installation of antenna

• Please connect the specified antenna to the antenna connector.
  Make sure to tighten with an RP-SMA torque wrench (0.6-1.0 Nm).
  ***** The main unit antenna connector may be damaged if tightened with a mechanical wrench.
  

• The antenna head shall be fixed according to the usage method of each antenna.

• When fixing the antenna coaxial cables, do not tighten them to such an extent that it deforms the coaxial cables.
  (This may affect the properties.)

Wiring

• Please carry out the wiring of the power and signal wires according to the pin configuration diagram in the figure below.
• Make sure to use twisted-pair wiring.
• It is recommended to use rod terminals at the tip of the wire.
  | Phoenix Contact-made
  ---|---
  Rodless sleeve terminalAI0.25-8-YE-3203037AWG26-24
  Rodless sleeve terminalA0.25-7-3202478AWG26-24
  Rodless sleeve terminalA0.34-7-3009202AWG22
  Single wire-AWG26-20
  Stranded wire -AWG26-20

Pin configuration| A1: Power supply DC+24V Input|
---|---|---
B1: Supply GND (0V)
A2:OUT RS-485 daisy chain connection output| If RS-485 communication is not used, no connection is required.
A3:OUT RS-485 daisy chain connection output-
A4: SG ground (bus side)
B2:IN RS-485 daisy chain connection input
B3:IN RS-485 daisy chain connection input –
B4: SG ground (bus side)

***** Please use RS-485 ground A4 and B4 as required.
The RS-485 communication unit is isolated from internal circuits.

• LAN Cable is a shielded twisted pair type.

DIP-SW settings

• Use DIP-SW to set the device ID for serial communication, the IP address for Ethernet communication, the switching of communication mode, on/off of termination resistor, and on/off of test mode.
  Please refer to the user manual of the equipment for details.
  

LED display

The LED display at the time of action shows the status display in the following table.

Guarantee provisions

9.1 Warranty terms

1. Guarantee period
   The warranty period of this product is one year after purchase or delivery to the designated place.
   It should be noted that the warranty period of the repaired products will not exceed the warranty period before the repair.
   Furthermore, regardless of the warranty period, the price of the Company’s products does not include service fees such as technical personnel dispatch.

2. Scope of guarantee
   If this product fails during the above warranty period, the Company will provide free replacement products or repair the faulty products at the place where the products are purchased.
   However, if the cause of the failure is the following (a-h), it is not included in this warranty.
   a. Regarding use relating to conditions, environments, and handling conditions other than those recorded in the operating instructions, user manuals, and main unit attention labels
   b. In case of reasons other than this product
   c. In case of renovation or repair by a party except for the Company or a service company commissioned by the Company
   d. In case of uses other than the original purpose
   e. In case of application in equipment, production lines, or systems that do not conform to or do not abide by the regulations, safety, and industry standards
   f. In the event that the scientific and technical level at the time of shipment from the Company can’t be predicted.
   g. Other reasons other than the Company’s responsibility, such as natural disasters or disasters.
   The warranty here refers to a single warranty for the Company’s single products, and the damage caused by the failure of the Company’s products is not included in the scope of the guarantee.

9.2 Limitation of liability

1. No matter whether it is within the warranty period or not, the Company shall not be liable for any damage caused by reasons not attributable to the Company, the ompany shall not be responsible for the opportunity loss and profit loss caused to customers due to the failure of this product, the damage caused by special circumstances foreseen or unforeseen by the Company, secondary damage and accident compensation, the damage caused by products other than this product and the compensation for other businesses.
2. The Company does not assume any responsibility for the consequences arising from the program of this product.
3. The customer shall confirm the compatibility of this product with the systems, machines, and equipment used. Otherwise, the Company is not responsible for the compatibility of this product.

9.3 Terms and Conditions

1. This product is used under such conditions that even if this product fails or nonconformity occurs, the application will not cause serious accidents, and in the event of a failure or failure, backup and fail-safe functions will be systematically performed outside the device.
2. The Company’s products are designed and manufactured as general products for general industrial applications. Therefore, the Company’s products are not suitable for applications requiring special quality assurance systems, such as applications that may cause serious risks to life or property. However, even if oriented to these purposes, the products can be applied if the customer agrees not to require special quality under the condition of limited use.
3. The application instances recorded in the catalog, etc. are for reference only, therefore, please confirm the functions and safety of the machines and devices before using them.

9.4 Specification changes
The product specifications and accessories described on the Company’s website, catalog, user manual, and user manual may be changed as necessary due to improvement or other reasons. Please consult your supplier for the actual specifications of our products.

NITTOKU CO., LTD.
2-292-1 Higashi-cho, Omiya-ku, Saitama-shi, Saitama-ken, 330-0841
TEL: (81) 48-615-2117 (direct dial call)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>