HIGHSTAR HSD306A LED Table Lamp Instruction Manual
- June 6, 2024
- HIGHSTAR
Table of Contents
Instruction Manual
Main Features & Technical Parameters
● Power supply: input AC100-240V 50/60Hz, output DC12V/2A
● Rated power of product: 21W
● Rated power of lamp: 6W
● Dimming type: Capacitive touch control ON/OFF key, Step-less dimming
● Timing shutdown: Smart timing lights (on/off auto-control)
● Light source: 40 pcs High photosynthetic efficiency semiconductor
LED
● Three light modes switch: natural light-white light-yellow light
● Color temperature: 2700-6500K
● Color rendering index (CRI): Ra≥90
● Max illuminance: ≥1000LUX (The Intensity of Illumination measured from the
lamp perpendicular to the table top 33cm distance)
● Wireless charging output: 10W(MAX)
Instruction
- Function: Put the lamp on the table and connect power at first. And press button, short press button to switch on, The default light is the natural light, press again to switch off. Short press the light switch button, and the lamplight changes circularly (Natural－White－ Yellow light).
- Brightness adjustment: In lighted state, Long press button to change brightness of lamp.
- Timer function: In lighted state, long press to start timer off function. then, the light flashes 2 times it means countdown functionstarting , and the light will be off automatically in 40 minutes. If you Press again during this period, it will be restart 40 minutes countdown light off function, until end of the countdown function, the lights automatically turned off.
Wireless charging instruction
- Wireless charging function: when the lamp power supply is on, put a mobile phone with a wireless receiver function (or a mobile phone with a wireless charging receiver module) on the desk lamp of a wireless charging icon in the center area, observing the power icon on the phone, if the display is charging, it explains the phone has been in the state of wireless charging. Meanwhile, the wireless charging indicator turns green. When the wireless charging indicator is red or flashing, means the wireless charging receiving function is not working stated; When the status light is green and red on means fully charged. But not all mobile phones with wireless charging functions.
- To be the best using effects and charge efficiency, attention to the wireless receiving position of the mobile terminal must be in full contact with the wireless charging icon on the lamp surface and be in the central area.
Cautions
-
Please ensure using the power supply matches DC12V/2A.
If the power adapter or flexible wire is damaged, It only can be replaced by the manufacturer or agent, or by a similarly qualified person. -
For indoor use only.
-
Please pay attention to the eyes hurting while using the lamp, the distance should not close.
-
Please make sure the product is without strong electromagnetic interference, otherwise maybe lights on or turned off.
-
The hose part of the lamp pole can not bend continuously and quickly, which can easily lead to lamp pole damage.
-
Please change a new one, when the light source is used up, cause of this light source is can not be alternative.
-
Please pay attention when used on countertops with a tilt greater than
-
degrees. might be dumping.
Product Illustration
Packing Accessories
- Power Adapter *1
- Instruction manual * 1
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
RF Exposure Warning Statements:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment shall be installed and operated with
a minimum distance of 20cm between the radiator & body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>