Konwin FP201R Electric Fireplace Logs Heater Owner’s Manual
- June 16, 2024
- Konwin
Table of Contents
Konwin FP201R Electric Fireplace Logs Heater
Thank you for choosing our heater. This user manual will provide you with valuable information necessary for the proper care and maintenance of your new product. Please take a few moments to thoroughly read the instructions and familiarize yourself with all the operational aspects of your new product
INTRODUCTION
Please take a few minutes to read this manual carefully. Proper maintenance and operation of this machine can provide better service.
SAFETY TIPS & WARNINGS
When using this electric unit, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
- Read all instructions before using this unit.
- CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater yourself.
- This heater may get hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces.
- Keep combustible materials, such as furniture, pillows, bedding, paper, clothes, and curtains at least 3 ft from the front of the heater and keep them away from the sides, top, and rear. DO NOT place towels or other objects on the heater.
- Extreme caution is necessary when any heater is used by or near children or the disabled, or when the heater is left operating and unattended.
- 6. DO NOT operate any heater with a damaged cord or after the heater malfunctions, has been dropped or damaged in any manner. Return the heater to an authorized service facility for examination, electrical or mechanical adjustment, or repair.
- This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations. NEVER locate a heater where it may fall into a bathtub or other water container. To protect against electrical hazards, DO NOT immerse in water or other liquids.
- DO NOT touch the control panel or plug with a wet hand.
- DO NOT run a cord under the carpeting. DO NOT cover the cord with throw rugs, runners, or similar coverings. Arrange the cord away from the traffic area and where it will not be tripped over.(
- DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- To prevent a possible fire, DO NOT block the air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where openings may become blocked.
- A heater has hot and arcing or sparking parts inside. DO NOT use in areas where gasoline, paint, explosive, and/or flammable liquids are used or stored. Keep the unit away from heated surfaces and open flames.
- Always plug heaters directly into a wall outlet/receptacle Never use with an extension cord or relocatable power tap (Outlet / Power strip).
- To avoid fire or shock hazards, plug the unit directly into a 120 V AC electrical outlet.
- To disconnect the heater, turn the controls to OFF, then remove the plug from the outlet. Pull firmly on the plug, DO NOT unplug by pulling on the cord.
- Always unplug the unit before moving or cleaning, or whenever the heater is not in use.
- Use only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by unauthorized dealers may cause hazards.
- Always use on a dry, level surface. Use on the floor only.
- DO NOT use outdoors.
- WARNING: To reduce the risk of fire or electric shock, DO NOT use this unit with any solid-state speed control device.
- DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. Qualified personnel should perform all servicing only.
PARTS & ACCESSORIES
SPECIFICATIONS
| Voltage Rating | 120 V / 60 Hz |
|---|---|
| Power Consumption | 1500 W |
| Unit Size | 20.5 in. (W) x 8.7 in. (D) x 12.2 in. (H) |
| Unit Weight | 12.23 LB |
PRODUCT DIAGRAM
CONTROL PANEL
REMOTE CONTROL
The remote control uses on button cell battery, type CR2025(3V). To remove the battery carriage use your thumb to squeeze the release tab to the right and then pull the carriage out. Place the battery into the carriage and slide the carriage back into the remote.
NOTE:
Follow battery disposal instructions on battery packaging, or contact your
local safety council for safe disposal of batteries.
Before using the remote control, you must remove the insulating film.
- All functions performed with remote control work identically to the heater control panel.
- Aim the remote control at the heater control panel to operate the heater.
PREPARATION
Place the heater on a firm, level surface and plug into a 120V 60Hz power outlet. Caution: The rear of the heater should be at least 4 inch away from the wall. Please pull the insulating film out of the battery cover before using the remote control.
OPERATING INSTRUCTIONS
Turn on / off the heater
First turn on the Power switch on the right side of the heater. The Power switch supplies power to all the functions of the fireplace. This switch must be in the “ I ” position for any functions including the remote control to work.
- Press the Power button on the remote control, the heat and flame effect will be on. Press the Power button again, the heat and flame effect will be off immediately (but the fan will prolong working for 30 seconds), and then the heater goes into standby mode.
Setting timer-power-off
Caution : Only under power-on mode can you set the timer-power-off function.
Setting timer-power-on
Caution: Only under standby mode can you set the timer-power-on function.
Setting heat
Under standby mode, press the Heater button to start the heater.
Under standby mode, press the Heater button on the control panel or remote
control, and the heater will start (The heater indicator is under the
artificial charcoal set. When heat is on, the charcoal set will be lit up and
flicker automatically at a slow pace). Press the Heater button again. The heat
and heater indicator will be off while the fan will prolong working for 30
seconds to emit plenty of heat inside.
Caution: When the flame is on, the heater indicator will keep lit up if
you turn off the heat.
Setting flame
Under standby, press the Flame button to watch the flame effect.
Under standby, press the Flame button, and the flame will be on at brightest.
The charcoal set will be lit up and flicker automatically at a slow pace. Each
time this button is pressed, the intensity of the flame decreases. There are
five brightness levels you can cycle through including the OFF setting.
Caution : When the heat is on, the charcoal set will keep lit up if you
turn off the flame.
NOTE:
When using the heater for the first time, it is normal for the hot wind with a
bad smell. It will disappear after a few minutes.
OVERHEAT PROTECTION
This heater is protected with an overheat protection that switches off the appliance automatically in case of overheat, e.g. due to the total or partial obstruction of the grids. In this case, unplug the appliance, wait about 30 minutes for it to cool, and remove the object that is obstructing the grids. Then switch it back on as described above. The appliance should operate normally. Should the problem persist, please contact the customer service.
MAINTENANCE
- Turn off the heater of the power switch.
- Unplug the unit and let it cool completely.
- To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. You may use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth . CAUTION: DO NOT let liquid enter the heater.
- DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes to clean the heater. This may cause damage or deterioration to the surface of the heater.
- DO NOT immerse the heater in water.
- Wait until the unit is completely dry before use.
- If won’t use the unit for a long time, please take out battery in the remote control according to the following steps, then take care of the remote control.
STORAGE
Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use the original packaging to repack the unit.
TROUBLESHOOTING
If the heater will not operate, please check the following before seeking repair advice:
- Check if the power cord is plugged into an electrical outlet, if not, plug it in.
- Check if the electricity to the main power switch (in the back) is working.
- Check the power switch is on.
contact
- CUSTOMER SERVICE EMAIL
- E-mail: Warranty@konwinchina.com
- Warranty@konwinchina.com
Scan this QR code to watch our product introduction video
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>