ZINGO High Speed RC Car Instruction Manual

ZINGO High-Speed RC Car

Thank you for purchasing the Zingo High-Speed RC car. With proper care. your new Zingo High-Speed RC car will provide you with many hours of enjoyment. Please read this ins\ructionmanual completely before using the product for the first time, and\henkeepthis the manual in a handy place for future reference

CHARGING THE BATTERY

1.  Turn off the lingo High-Speed RCcarthen and insert the charging plug into the truck charging socket onthebo1tom. The charging plugins only one way. Dot not force it(see illustration,B).
2.  Connect the USB end of the cable to your computer USB port or a USB wall charger(sea diagrams), The Red CHARGE indicator light turns OFF while charging is in progress
3.  The average charging time Is approximately 30 minutes (via 5.0V ::: 2A USB wall charger). The truck ope1ates for approxima1ely 13-15mlnutes on full charge
4.  The red charging indicator turns on when the battery is fully charged

Note: Periodically examine the charger for external damage. External damage to the charger may result in the risk of fire. elec1ricshock.or injury to persons. Never use a damaged adapter

•  Install the battery on the remote control using the enclosed screwdriver to open the battery cover on the remote control see diagram no  D. Insert 2 AA batteries not included  into the battery compartment matching  polarity +and – marked inside replace  the battery  cover and secure it

SYNCING YOUR ZINGO HIGH-SPEED RC CAR

Your Zingo HighSpeed RC car features an automatic 2.4 G channel selection system that allows up to 1o8 people to race side by side in 1he same wireless range

For One Player:

•  Before starting, make sure that the power on both your remote control and truck are in the OFF position. Make sure that there are no other2.4Gdevlces ln the area.
•  TurnONthetruck and set lt down on a flat surface the headlight will turn on
•  Turn ON the remote control and pull the 1hroltle all the way down. your truck and remote control should sync.lf pairing fails, repeat steps 1-3

For Multiple Players:

•  Before star1ing.make sure that the power on all 1rucks and controllers are in the OFF position. Make sure that 1hereare no other2.4Gdevices in the area
•  Each person must sync their truck one at a time to avoid interference Follow steps 1 to3 above.
•  After syncing, leave1he the truck ON until all players have synced their trucks.
•  if there is interference all players must turn off their controllers and trucks and restart the syncing process

OPERATION

1. Turn your truck on:
   •  Fully charge your Zingo High-Speed RC car and install 2 new AA bat1eries into the controller.
   •  Sync your truck to 1he remote control and set the truck on the ground.
2. Driving your truck ·
   •  Push the throttle halfway to drive forward at low speed. Pull the throttle fully lo drive at high speed
   •  Pushthe 1hroltlelorwardto make truckmove in reverse
   •  Turn the steering control to counter-clockwise to turn the truck left.
   • urn steering to the clockwise to tumthetruckright
   •  To break or quickly stop simply pull or push\hethrotlle in the opposi1e direction

SPEED MODE SWITCH
You can drive your Zingo HighSpead RC car in a low or high-speed setting. Simply push! the Speed Mode Switch to righ1 to change from low to the high- speed mode.

THROTTLE TRIM
If your Zingo HighSpeed RC car automatically goes forward or backward. simply adjust the Throttle Trim untiltheZingo the HighSpeed RC car remains in a neutral position

STEERING WHEEL TRIM ADJUSTMENT

lf the Truck pulls to the right or left, you may need to adjust the steering wheel trim on the bottom of the truck from time to time to keep your Zingo High-Speed RC car driving straight.(see diagram E

Warning DO NOT USE TRUCK IN INCLEMENT WEATHER!

TROUBLESHOOTING

Before sending your truck in for repair, please check for a solution below .

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Rules

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/
• TV technician for help .

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>