THOVAS CK10R LED Surface Mounted Accent Lights with Remote Control User Manual
- June 6, 2024
- THOVAS
Table of Contents
Made in China
ITEM No.: CK1 0 R
LED SURFACE-MOUNTED ACCENT LIGHTS WITH REMOTE CONTROL
ASSEMBLY AND INSTALLATION INSTRUCTIONS ARE IMPORTANT, RETAIN THEM FOR
FUTURE REFERENCE: READ CAREFULLY
PARTS AND SPECIFICATIONS
Batte Installation
REMOTE CONTROL -CR2025 battery pre-installed. This product contains a button battery. If swallowed, it could cause severe injury or death in just1 hour. Seek medical attention immediately (On First Use, Remove Battery Compartment Protective Plastic)
Battery Replacement
REMOTE CONTROL
- CR2025 battery required.
- Loosen battery compartment retaining screw.
- Slide the battery drawer out.
- Remove the battery.
- Place the new battery in position aligning polarity (+) (-) as indicated. – Slide the battery drawer in.
- Tighten the battery compartment retaining screw.
LED ACCENT LIGHTS
- Rechargeable Battery
- Open by rotating A’s until aligned.
- Place the USB charger cable into the lamp Micro USB Port
- The RED light is on in charge, the light is off automatically when it is in full charge.
- Close by rotating A’s until out of alignment.
Operating Instructions
LED ACCENT LIGHTS
– Manual Operation When the battery is fully charged. turn ON each puck by
lightly touching the V triangle mark on the puck side. Repeat touch the
triangle mark to turn the unit OFF. Light brightness will default to previous
settings.
LED ACCENT LIGHTS – Remote Control Operation
The remote control unit will operate lights within a 7 m / 21 ft range. Once the battery is fully charged turn all lights ON by pointing the remote control towards the sensor. Use the DIMMER and TIMER functions by pointing the remote control towards the sensor and selecting the desired function.
ADDING LIGHTS TO A SET
Up to 48 lights may be controlled by one remote control. No programming is
needed. Any similar puck lights will be controlled when placed within the
range of the remote control’s signal.
Mounting Instructions
LED ACCENT LIGHTS – Adhesive Mounting Pads Included Remove the protective paper on one side of the Mounting Pad and apply to the battery cover (use caution as the adhesive is very strong). Position the light in the desired location. Remove the second protective paper and apply pressure to set the adhesive. Once applied the light is permanently mounted. This is a permanent tape that may cause damage if removed. Not recommended for use on wallpaper or delicate surfaces.
WARNING
- This product is not a toy and contains small parts. Close supervision is necessary when this unit is used near children.
- To reduce the risk of electrical shock, do not put the unit in water or other liquid. For cleaning, use a soft dry cloth. Do not place or store appliances where it can fall or be pulled into a tub or sink.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation this equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: 1)This device may not cause harmful
interference. 2)This device must accept any interference received, including
interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
One Year Limited Warranty
www.thovas.net , warrants to the original retail purchaser, that this product is free of defects in material and workmanship for a period of up to one year from date of original purchase. Warranty applies only to the original purchaser of the product. Warranty is limited to consumer use and does not cover parts damaged due to normal wear, abnormal conditions, misuse, or accidents, and is limited to repair or replacement only. This limited warranty does not cover bulbs or batteries, or any part that may become defective due to mishandling. Warranty is effective only upon presentation of the dated proof of purchase. Customers are responsible for all postage costs on returned merchandise. No shipping or handling charges will be reimbursed.
Limitations on Warranty Disclaimers
There are no warranties that extend beyond the description on the face hereof. This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.
For assistance with assembly or installation, parts, and customer service, please do not return to retailer – contact THOVAS CUSTOMER SERVICE at:
http://www.thovas.net
Mail: info@thovas.net
http://www.thovas.net
ROHS
Protecting the Environment – Recycle It
Responsibly recycling these products saves natural resources and protects
human health through the reuse of reclaimed resources. Please call your local
waste management company for vendors in your immediate area.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>