TORTECO T09 True Wireless Bluetooth Headset User Guide
- June 6, 2024
- TORTECO
Table of Contents
T09
TRUE WIRELESS STEREO
DESCRIPTION
- LED Indicator
- Power Button/Call Button
- Indicator Of Charging Case
- Charging Port of Charging Case
- Contact Charging Pod
- Ear Tip
SPECIFICATION
| BT Version | V5.0 |
|---|---|
| BT Protocol | HFP. HSP AVRCP A2DP |
| Transmission Distance | 10M |
| Speaker Diameter | 6.0mm |
| Frequency Response Range | 20-20KHZ |
| Impedance | 16Ω |
| Sensitivity (Speaker) | 97db 3db |
| Rated Power | 20mW |
| Sensitivity (MIC) | -42db±3db |
| Career Frequency | 2.402GHz-2.480GHz |
| Battery Capacity(Earbud) | 50mAh |
| Charging Time(Earbud) | About 2 hours |
| Music Time | About 3-4 hours |
| Battery Capacity(Case) | 400mAh |
| Charging Time(Case) | About 2 hours |
| Battery Life(Case) | Providing 3-4 charges for earbuds |
| Working Current | 16mA |
| Standby Current | 1mA |
| Shutdown Current | 20uA |
| Charging Voltage | DC5V 300MA |
| Size(Earbud, LWH) | 21.515.513mm |
| Size(Case, LWH) | 603728mm |
| Optional Accessories | Type c USB charging cable |
Silicon ear tips(Size L,M,S)
Working Temperature| 0~45°C
Storage Temperature| -20~70°C
How to use
Power on:
Press the switch button for 2 seconds.
Pairing:
TWS pairing: power on the L, R earphones at the same time after restored to
the factory settings, the L, R earphones are into the pairing (the left and
right earphones have been paired at the factory). Phone paling: 1. After the
L,R headsets are successfully paired, they will automatically enter the phone
pairing: 2. Take up the L, R headsets from the base, they will automatically
connect, and the R headset enters the pairing (the connected phone will
automatically connect) 3. Single headset use: Take up any one of the
headphones from the base, and automatically enter the pairing in about 5
seconds (if it has been paired with the mobile phone it will be automatically
connected in about 5 seconds). Press and hold the power button for 4 seconds
to enter the pairing in off state.
Connect:
Open the phone Bluetooth search for “T09” and click for pairing, if the phone
has been paired with headphones, it will automatically reconnect when powered
on.
Shutdown: Press and hold the power button for 4 second.
Answer:
Press the power button once(any left and right headphones).
Reject the call:
Press and hold the power button for 2 seconds.
Hang up:
Press the power button once (any left and right headphones).
Play/Pause: Short press the power button.
Previous and next track:
Click twice of left headset, music status previous music; Click twice of right
headset music status next music.
Phone and headset call switching:
Press the power button for 2 seconds during a call.
Charging:
Charging the earphones by closing the charging case cover, the red light is
solid on Fully charged: Lights off after 10 seconds of white light.
Low battery:
Prompt tone once when the 3.5V low battery, and the red Ight flashes every 7
seconds
Auto power off:
Auto power off. It will automatically power off in 5 minutes when no
connection status, Bluetooth is not connected to any device. The L, R headsets
will automatically shut down when successfully connected but not conned with
the phone for 5 minutes
Reset: Put the earphones into the charging case to reset
Restore factory settings:
Press the power button for 10 seconds in the power off state, clear the
Bluetooth pairing list/restore the default volume, you need to re-pair the TWS
headset alter clearing.
Charging case function:
Open the cover to power on, close the cover to power off.
Problem & solutions
| Problem | Solution |
|---|---|
| Multiple connection are not successful |
- Make sure the earbuds are in search mode, Or switch on again
- There are too many BT devices around which makes searching difficult. Close the BT function of irrelevant devices.
Voice is small or distorted|
- Check the volume of the BT device and adjust its volume to the Voice is small or distorted appropriate level
- Low battery Recharge it.
Music sound doesn’t play fluently| Make sure your BT device is within the
effective connection distance of the play fluently earbuds, or there are no
obstacles between the earbuds and BT device.
Bluetooth status indicator doesn’t work|
-
Indicates that the battery is low
Recharge and try again doesn’t work. -
Switch on again.
We recommend output voltage of the case charger is DC 5V+/-25V and the current is 100MA-500MA. An over-high charging voltage may damage the charging case.
Safety rules
-
Do not remove or refit headset for any reason, otherwise it may cause headset fault and burning.
-
Do not wet the device in contact with liquid, otherwise it will cause serious damage to the device. The manufacturer will not guarantee the damage caused by water inflow of the device.
-
Do not place the device in the environment with too high or too low temperature (above 75 °C or below-40 °C) for a long time.
-
Please avoid using the device indicator light near the eyes of children or animals.
-
Do not use be device in thunderstorm weather.
Thunderstorm may cause abnormal operation of the device and increase the risk of electric shock. -
Do not treat this electronic device as ordinary garbage when it is discarded. In order to reduce pollution and protect the earth’s environment to the greatest extent, please recycle it.
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>