Seong Ji Industrial BTM530A Bluetooth Module User Manual

Seong Ji Industrial BTM530A Bluetooth Module User Manual

Introduction

BTM530A is Bluetooth 4.2 products, including embedded UART interface optimized for Mac and compatible radio / low-power applications

The core chipset is from Qualcomm, part number CSR8811A12.

Hardware Architecture:

Main Chipset Information

CSR8811A12

Circuit Block Diagram

The major internal and external block diagram of BTM530A is illustrated in Figure 1-1.

Operational Description

It is mounted in the sound-bar communication controller for using a wireless device user the Bluetooth devices that act.

Channel based on the 802.15.1 / 1a of the Bluetooth standard IEEE 79 channels and frequency use the 2402MHz ~ 2480MHz band and channel interval is 1 MHz.

• Features

  • Bluetooth 4.2
  • Full-speed Bluetooth operation with full piconet and scatternet support
  • High-sensitivity Bluetooth receiver
  • On-chip balun
  • Support for IEEE 802 ® .11 coexistence

• Time base of the RF frequency
  For IF and RF frequency, a crystal(26MHz) is a clock reference.

• Synthesizer
  Transceiver size is relatively fresh inside the internal voltage controlled oscillator (VCO) and the PLL system
  To respond to a wide adjustment range.

• Transmission
  Baseband processing FHSS (frequency hopping spread spectrum run) and (2FSK / DQPSK / 8DPSK) modulation, Data transfer speed is 1Mbps, 2Mbps (EDR), it will have a 3Mbps (EDR). It handles the digital data signal to 2FSK, 1MHz Data Rate by the DAC in the BBP IC TX IQ signal is input through the modulation process and a TX carrier frequency the amplifier stage shelter will be sent.

• Receiver
  This transceiver IC is isolated to prevent unwanted noisy radiation by internal amplifier noise LOW month and the RF signal is through the intermediate frequency conversion and demodulation, and a RX IQ signal via a low-pass filter the input to baseband Processing.

• Product Specifications

  • Standards: Bluetooth 4.2
  • Data Modulation GFSK, 8DPSK
  • Frequency Range 2402-2480MHz
  • Module power output
    Parameter| Min| Typ.| Max| Unit
    ---|---|---|---|---
    RF Characteristics
    RF Frequency Range| 2.402| –| 2.480| GHz
    Output power [TRM/CA/01/C] class1(0.25~10mW)| 4.0| 7.0| 9.99| dBm
    TX Spurious Emission

30.0MHz to 1.0GHz

1.0GHz to 12.5GHz

1.8GHz to 1.9GHz

5.15GHz to 5.3GHz

| –| –| -35| dBm
TX Frequency Tolerance| -75| –| 75| KHz
Receiver sensitivity    BER at -70dBm| –| –| 0.1| %
Maximum Input Level BER at -20dBm| –| –| 0.1| %

• Operating Voltage: 3.3V(3.0~3.6V)
• Size: 18mm X 28.5mm X 5.1mm
• Temperature, humidity range: -20 ℃ ~ + 70 ℃

Notice

Approval Statement

CE Statement

Contact Address: SEONG JI INDUSTRIAL CO., LTD, / 54-33, Dongtanhana 1-gil, Gyeonggi-do Hwaseong-si South Korea

FCC approval

This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesirable operation.

To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product.

Contains Transmitter module FCC ID: 2AS8LBTM530A

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
• The OEM integrator is responsible for ensuring the end-user has no manual instruction to remove or install module.
• The module is limited to installation in mobile or fixed applications.

Regulatory notice to host manufacturer according to KDB 996369 D03 OEM Manual v01

List of applicable FCC rules
This module has been granted modular approval as FCC Rule parts 15C(15.247).

Summarize the specific operational use conditions

The OEM integrator should use equivalent antennas which is the same type and equal or less gain  then an antenna listed in this instruction manual.

Antennas list

This module is certified with the following integrated antenna.

Type: Pattern antenna / Max. peak Antenna gain : 0 dBi
Any new antenna type, higher gain than listed antenna should be met the requirements of FCC rule 15.203 and 2.1043 as permissive change procedure.

Information on test modes and additional testing requirements

OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, additional transmitter in the host, etc.).

Additional testing, Part 15 Subpart B disclaimer

The final host product also requires Part 15 subpart B compliance testing with the modular transmitter installed to be properly authorized for operation as a Part 15 digital device.

IC approval

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

The host device must be labeled to display the Industry Canada certification number of the module.
Contains transmitter module IC:25119-BTM530A

IMPORTANT NOTE

This device complies with FCC & IC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and must not be co- located or operating in conjunction with any other antenna or transmitter.

This device is intended only for OEM integrators under the following conditions:

1. This module may not be co-located with any other transmitters or antennas.
2. The antenna must be installed such that 20cm is maintained between the antenna and users.

As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements with this module installed.

In the event that these conditions cannot be met, then the FCC & IC authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product including this module and obtaining separate FCC & IC authorizations.

User Information
Caution: Any changed or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate this equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>