iLIVE ISB202 Wireless Party Speaker User Guide
- June 6, 2024
- iLive
Table of Contents
iLIVE ISB202 Wireless Party Speaker
Features
- Bluetooth wireless 5.0: range 59 ft.
- Micro SD card port
- Digital volume control
- Voice prompts
- Built-in rechargeable battery: approximately 7 hrs of playtime at 50% volume
- Micro-USB port for battery recharge
Includes
- User’s Guide
- Micro-USB to USB charging cable
Controls
- Mode: Press to change source modes to Bluetooth, Aux, USB or Micro SD/TF. Press and hold to turn LED lights ON/OFF.
- Volume-/Previous: Press to decrease volume level. Press and hold to play previous track.
- Play/Pair: While playing music, press to play/pause tracks. Press and hold for 3 seconds to pair Bluetooth device manually.
- Volume+/Next: Press to increase volume level. Press and hold to play the next track.
Note :To turn voice prompts ON/OFF, press and hold both the Volume+ / Volume- buttons for 3 seconds.
Inputs
Charging the Battery
To charge the internal battery, plug the USB charging cable into the DC Power Input on the speaker and a powered on computer or USB power adapter (not included) and standard power outlet. Charging time is approximately 4 hours. When the battery is low a voice will announce “Low Battery;’ and then the unit will automatically power OFF. While the unit is charging the LED Indicator will display a solid red light. When the battery is fully charged the light will turn off.
Pairing & Playing Bluetooth Audio
- When first powered on, the speaker defaults to Bluetooth Mode and is ready to pair automatically. When pairing, remain within 3 feet of the Bluetooth device.
- Using the controls on your Bluetooth device, select 15B202 in the Bluetooth Settings to pair. If need be, refer to the user’s manual for your specific device for more information.
- When successfully paired, a voice will announce, “Bluetooth is connected:’ The LED Indicator will display a solid blue light. Your Bluetooth device will now be heard through the speaker.
- Use the controls on the connected Bluetooth device to select and play audio. Use the speaker controls or the connected Bluetooth device to play, pause, and adjust the volume level.
- After initial pairing, the speaker will automatically connect to the last Bluetooth device used whenever it is in Bluetooth Mode. Note: If your device should become unpaired or you find it is unable to connect, press and hold the Play/Pair button to enter to Pairing Mode. A voice will announce, “Bluetooth is connecting,” and you can connect to the speaker manually.
USB &TF/Mlcro SD
- Load a USB or a Micro SD memory card Into the appropriate media port
- The speaker will automatically switch to USB/SD mode.
- Use the controls on your device to select and play audio from the connected drive.
Aux in
Requires a 35mm audio cable (not included).
- Connect a 35mm audio cable to the Aux In on the unlt and the audio output/headphone jack on an audio device.
- The speaker will automatically switch to Allx Mada.
- Use the controls on the connected device to select and play audio. Be sure the volume on your connected device is audible when you begin playing.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning : Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment o and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>