HENDI 212028 Crepe Maker User Manual

: June 6, 2024
: HENDI

Table of Contents

Safety regulations
Special Safety Regulations
Troubleshooting
Technical specification
Warranty
Discarding & Environment
Documents / Resources

CRÊPE MAKER
212028 HENDI 212028 Crepe Maker

You should read this user manual carefully before using the appliance.
Keep these instructions with the appliance.
indoor For indoor use only.
food contac

Dear Customer,
Thank you for purchasing this Hendi appliance. Before using the appliance for the first time, please read this manual carefully, paying particular attention to the safety regulations outlined below.

Safety regulations

This appliance is intended for commercial use.
The appliance must only be used for the purpose for which it was intended and designed.
The manufacturer is not liable for any damage caused by incorrect operation and improper use.
Keep the appliance and electrical plug away from water and any other liquids. In the event that the appliance should fall into the water, immediately remove the plug from the socket and do not use it until the appliance has been checked by a certified technician. Failure to follow these instructions could cause a risk to lives.
Never attempt to open the casing of the appliance yourself. Do not insert any objects in the casing of the appliance.
Do not touch the plug with wet or damp hands.
The danger of electric shock! Do not attempt to repair the appliance yourself. In case of malfunctions, repairs are to be conducted by qualified personnel only.
Never use a damaged appliance! Disconnect the appliance from the electrical outlet and contact the retailer if it is damaged.
Warning! Do not immerse the electrical parts of the appliance in water or other liquids. Never hold the appliance under running water.
Regularly check the power plug and cord for any damage. If the power plug or power cord is damaged, it must be replaced by a service agent or similarly qualified persons in order to avoid danger or injury.
Make sure the cord does not come in contact with sharp or hot objects and keep it away from an open fire. To pull the plug out of the socket, always pull on the plug and not on the cord.
Ensure that the cord (or extension cord) is positioned so that it will not cause a trip hazard.
Always keep an eye on the appliance when in use.
Turn off the appliance before pulling the plug out of the socket.
Never carry the appliance by the cord.
Do not use any extra devices that are not supplied along with the appliance.
Only connect the appliance to an electrical outlet with the voltage and frequency mentioned on the appliance label.
Connect the power plug to an easily accessible electrical outlet so that in case of emergency the appliance can be unplugged immediately. To completely switch off the appliance pull the power plug out of the electrical outlet.
Always turn the appliance off before disconnecting the plug.
Never use accessories other than those recommended by the manufacturer. Failure to do so could pose a safety risk to the user and could damage the appliance. Only use original parts and accessories.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory, or mental capabilities, or lack of experience and knowledge.
This appliance must not be used by children under any circumstances.
Keep the appliance and its cord out of reach of children.
Always disconnect the appliance from the mains if it is left unattended or is not in use, and before assembly, disassembly or cleaning.
Never leave the appliance unattended during use.

Special Safety Regulations

Use the appliance only as described in this manual.
This appliance should be operated by trained personnel.
Caution! Hot surface! The temperature of the heating surface and other accessible surfaces is very high during use. Touch the temperature control knob only.
An equipotential bonding terminal is provided at the rear side of the appliance to allow cross bonding with other equipment.
When this appliance is to be positioned in close proximity to a wall, partitions, kitchen furniture, decorative finishes, etc., it is recommended that they are made of non-combustible material; if not, they shall be cladded with a suitable non-combustible heat insulating material, and that the closest attention be paid to fire prevention regulations.
Do not place the appliance on a heating object (gasoline, electric, charcoal cooker, etc.). Keep the appliance away from any hot surfaces and open flames. Always operate the appliance on a level, stable, clean, heat-resistant, and dry surface.
WARNING: Keep all ventilation openings in the appliance clear of obstruction.
WARNING: If the heating surface is cracked or damaged. Do not use the appliance.
Do not cover the appliance during operation.
Allow at least 20 cm spacing around the appliance for ventilation purposes during use.
Do not use hard utensils to hit the heating plate surface. Do not use water jet flush directly with water as the parts will get wet and electric shock might be result.
Caution! Securely route the power cord if necessary in order to prevent unintentional pulling or contact with the heating surface.
Clean the appliance after each use for the reason of hygiene.
WARNING: Allow completely cool down before cleaning and storage.

Intended use

The appliance is intended for professional use and can be operated only by qualified personnel.
This appliance is designed only for making crepe only. Any other use may lead to damage to the appliance or personal injury.
Operating the appliance for any other purpose shall be deemed a misuse of the device. The user shall be solely liable for improper use of the device.

Grounding installation

This appliance is classified as a protection class I appliance and must be connected to protective ground. Grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

Main parts of the appliance

HENDI 212028 Crepe Maker -Main parts

1. Temperature control
2. Power switch| 3. Heating indicator
4. Wooden spreader
---|---

Preparation before using for the first time

Remove all protective packaging and wrapping. Make sure no packaging debris remains on the appliance.
Check for completeness (1 wooden spreader included) and any transport damage. In case of damages or incomplete delivery, please contact the supplier (See — > Warranty page). Ensure there is enough clearance around the appliance. Place the appliance in a well-ventilated area.
Connect the power plug to a suitable electrical wall outlet.
Turn on the switch(2), start heating by setting the temperature control (1) clockwise to MAX (300°C) for dry running without food for about 15 ~ 20 minutes. This is to remove all residues during the manufacturing process.
Let the appliance cool down completely. Clean it before using it for a baking crepe. (See ==> Cleaning and Maintenance)

Note: Due to the manufacturing residues, the appliance may emit a slight odor in the first few cycles. This is normal and does not indicate any defect or hazard. Make sure the appliance is well ventilated.
Note: You will need a wooden spreader (4) on hand before starting to cook crepes because you have to handle them quickly while baking to avoid overcooking the batter.

Operation

Clean the baking surface with a clean damp cloth before each use & let dry afterward.
Connect the power plug with a suitable electrical outlet. Turn on the switch(2), it will light up in green to show that it is connected to the electrical power supply.
Start the appliance by turning the temperature control (1) in a clockwise direction to select the required baking temperature.
Wait for about 15 ~ 20 minutes to let the baking plate heat up to about 250-300°C (Max).
Then, pour a small amount of crepe batter onto the baking plate with a spoon. Use a wooden spreader (4) to spread it in circular movements. Note: Moisten the wood spreader before use. This prevents the batter from sticking to the spreader (4).
Allow the crepe to cook on one side until its surface is no longer liquid visibly. Use a wooden spatula or heat-resistant plastic spatula (not supplied) to lift one side of the crepe gently. The crepe should be visibly cooked, maybe some in brown. In this case, the crepe is ready to be flipped.
Note: When you pour the batter onto the hot baking plate, you might hear some slight cracking noise caused by the difference in temperature. This is normal.
Note: Do not overcook the crepe, or the texture will become rubbery. The crepe can be cooked quickly at high temperatures. So, t can be flipped within about 2~3 minutes if you select a suitable temperature.
Turn the crepe over to the other side carefully. It only needs to cook on the other side for about 30 ~ 40seconds.
Carefully remove the crepe from the baking plate. Continue making morecrepes until you ran out of batter. Do not use your hand to touch the crepe as it is still hot.
If necessary, adjust the temperature by rotating the temperature control.
Switch OFF the appliance by rotating the temperature control (1) anti-clockwise direction to 0°C and turn the switch(2) off.

Attention! Disconnect the power plug when not in use. Leave the appliance to cool down completely before cleaning and storing.

RESET the Hi-limiter (thermal cut-out)

Please note that a RESET button is located at the rear side of the appliance covered with a protective cap. (See diagram)

Unplug the appliance from the electrical outlet first.
Allow the appliance to completely cool down.
Unscrew the black protective cap of the RESET button.
Press the RESET button of the Hi-limiter (thermal cut-out). You should hear a click sound.
Screw back the protective cap on the RESET button.

Cleaning and Maintenance

Attention: Always unplug the appliance from the electrical power outlet and let it cool down completely before cleaning & storage.

Cleaning

Clean the appliance after each use.
Never immerse the appliance in water or other liquids.
Clean the outer surface with a slightly damp cloth or sponge with some mild soap solution.
Never use abrasive sponges or detergents, steel wool, or metallic utensils to clean the interior or exterior parts of the appliance.

Storage

Before storage, always make sure the appliance has already been disconnected from the electrical outlet and cooled down completely.
Store the appliance in a cool, clean, and dry place.
Never put objects on the baking surface as they may crack.

Troubleshooting

If the appliance does not function properly, please check the below table for the solution. If you are still unable to solve the problem, please contact the supplier/service provider.

Problems	Possible cause	Possible solution

Connected to the power supply but the power switch (2) does not light up when it is turned on.| The power plug is not connected
properly to the electrical power supply.| Check again to make sure it is connected properly.
Power switch (2) defective.| Contact your supplier.
Hi-limiter (Thermal cut-out) activates| RESET the Hi-limiter (thermal cut- out). See RESET on page 6.
The appliance does not heat up but the power switch (2) light up.| Temperature control (1) defective| Contact your supplier.
Heating element defective

Technical specification

Item no. : 212028
Operating voltage and frequency :
220-240V~ 50/60Hz
Rated input power: 3000W
Temperature setting : 50°C ~ 300°C (MAX)
Protection class: class I
Waterproof protection class: IPX3
Dimension : 520x470x(H)160mm
Net weight: approx. 22 kg
Net weight: approx. 22 kg
Remark: Technical specification is subject to change without prior notification.

Warranty

Any defect affecting the functionality of the appliance which becomes apparent within one year after purchase will be repaired by free repair or replacement provided the appliance has been used and maintained in accordance with the instructions and has not been abused or misused in any way. Your statutory rights are not affected. If the appliance is claimed under warranty, a state where and when it was purchased and include proof of purchase e.g. receipt).
In line with our policy of continuous product development, we reserve the right to change the product, packaging and documentation specifications
without notice.

Discarding & Environment

When decommissioning the appliance, the product must not be disposed of with other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point. Failure to follow this rule may be penalized in accordance with applicable regulations on waste disposal. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste for recycling, please contact your local waste collection company. The manufacturers and importers do not take responsibility for recycling, treatment, and ecological disposal, either directly or through a public system.

Hendi B.V.
Innovatielaan 6
6745 XW De Klomp, The Netherlands
Tel: +31 317 681 040
Email: info@hendi.eu
Hendi Polska Sp. z o.o.
ul. Firmowa 12
62-023 Robakowo, Poland
Tel: +48 61 658 7000
Email: info@hendi.pl
Hendi Food Service Equipment GmbH
Ehring 15
5112 Lamprechtshausen, Austria
Tel: +43 6274 200 10 0
Email: office.austria@hendi.eu
– Changes, printing and typesetting errors reserved.
© 2020 Hendi B.V. De Klomp – The Netherlands
Ver: 02-11-2020