GILIVER Multi-Functional Robot MaDe Zigybot Policeman Instructions

GILIVER Multi-Functional Robot MaDe Zigybot Policeman

Remote control battery explanation

Batteries installation in the transmitter:
Use a screwdriver to open the button cell gate of controller Put 2×1 .SV”AAA” batteries inside the battery box Put the gate back and use a screw to tighten the gate.

Battery Warning

• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Different types of batteries or new and used batteries are not to be mixed.
• Only batteries of the same or equivalent type as recommended are to be used. Batteries are to be inserted with correct polarity.
• Exhausted batteries are to be removed from the toy.
• The supply terminals are not to be short-circuited.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries. Always remove batteries from the toy when it is not being used for a long period of time. Do not dispose the battery in fire or heat.
• Do not use or leave the battery near a heat source such as fire or heater.
• Do not strike or throw the battery against hard surface.
• Do not immerse the battery in water, and keep the battery in a cool dry environment.

Robot recharging

Batteries installation in the robot:
To charge battery, please insert the USB port provided USB charging cable to anyone USB port of a computer, a power pack, a mobile charger or a car USB charger. The charging time is about 2-3 hours and the playing time is about 2 hours. Switch OFF the robot before charging.

Functional specifications

1. START THE ROBOT
   • After the power is turned on, the machine is turned on automatically.
   • In the sleep state, press the button of the switch machine to turn on the power, and the sound effect+, (starting action)
   • Play boot machine language.
   • At startup, press the button to stop the current function.
   • Power off state, press the chest button, perform the boot action.
2. STANDBY BUTTON
   • When the machine is switched on, and no sound or action is made, the first 20S prompt, and then the time is 45 seconds, no operation will play the standby voice. A total of 6 prompts (machine language),
   • The time is about 5 minutes still no operation, then play off the voice and go to sleep.
3. SHUTDOWN
   If standby time arrives, about 5 minutes. Play “machine language” + shut down sound. Then enter the power saving mode, unable to respond to infrared function. You need a chest button to reawaken.

4. WALK FORWARD
   After receiving the “walk forward” signal. You will walk, and you will always receive the “walking forward” signal, which will continue to do so continuously. There are sound effects in advance.

5. WALKBACK
   After receiving the “walk back” signal. You will walk back and receive a”walk back” signal that will continue to do so. There are sound effects in the back process.

6. TURN LEFT
   After receiving the “left turn” signal, the robot turns left (the left motor turns back, the right horse.It goes forward. There are sound effects in the rotation.

7. TURN RIGHT
   After receiving the “taxi right turn” signal, then the robot turns to the right (the left foot motor turns and the right foot motor turns back). There are sound effects in the rotation.

8. SLIDE FORWARD
   After receiving the “forward” signal, the robot moves forward. Always receive a “taxi forward” signal, which will continuously perform this action. There are sound effects in advance.

9. SLIDE BACK
   After receiving the “taxi back” signal, the robot slides back to move. Always receive the “glide back” signal, will continue to perform this action continuously. There are sound effects in the back process.

10. SLIDE LEFT
    After receiving the “taxi to left” signal, then the robot turns left (the left motor turns back and the right foot motor turns). There are sound effects in the rotation.

11. SLIDE LEFT
    After receiving the “sliding right turn” signal, the robot turns to the right (the left foot motor turns and the right foot motor turns back). There are sound effects in the rotation.

12. THE VOLUME+ (A TOTAL OF 5 LEVELS) DEFAULTS TO LEVEL 3
    A. After receiving the “volume +” signal, the sound increases the volume, and the sound is prompted, when the sound reaches the maximum, if it is still pressed, no sound prompt.

13. VOLUME – (A TOTAL OF 5 LEVELS) BY DEFAULT AT LEVEL 3.
    A. After receiving the “volume -” signal, the sound reduces the volume, and there are sound effects, when the sound reaches the maximum hour, if it is still pressed, there is no voice prompt.

14. STOP
    After receiving the “stop” signal, immediately stop the current function in any situation and enter standby mode. There are hints for speech.

15. PROGRAMMING
    After receiving the “programming” signal, the robot performs programming or programming playback functions.
    Received received signal “programming”, for the first time after the “drops” the state of programming, the all the launch button function can be any programming (+ – stop and volume, cruise, dance music programming except), can press the 30 most programming. Once you have finished programming, you receive the “programming” signal again, and the tooltip “execute the programming” robot is programmed to play back one by one. Or the 5S no longer input, will automatically execute the programming playback function.

16. DEMO FUNCTION
    After receiving the “demo function” signal, perform the demo function. Basic action demonstration.

17. DANCING
    After receiving the “dancing” signal, there are three pieces of dance music, with the action and light.

18. DANCE MUSIC PROGRAMMING
    After receiving the “dance music programming” signal, a total of 2 pieces of the head rhythm, playback the programming keys to make up the movement. The sound plays the opening rhythm. Action complete, end function.

19. THERE ARE THREE MACHINE LANGUAGE DEMONSTRATIONS IN MACHINE LANGUAGE.

20. MIDI HAS THREE MUSIC BEATS.
    AOD LIGHT TO THE ACTION.

21. FIRE
    After receiving the “firing” signal, every time the robot has a reminder, then the firing function is performed. There are six paragraphs, some of which are situational.

22. WATER SPRAY
    After receiving the “cruise” signal, “Sir, walk around, come with me, lala.” Then play the background sound (there are two), and the robot will move forward, between 30S and 60S, and will walk and talk.

  * 1\. Machine language 1
  * 2\. Machine language 2
  * 3\. Machine language 3
  * 4\. Machine language 4  

If you encounter obstacles in the process, you will avoid them and respond to the prompts. Make a dodge turn.

  * 1\. Sound effects 1
  * 2\. Sound effects 2
  * 3\. Sound 3
  * 4\. Sound effects 4  

After 20 minutes, if there is no obstacle, it will end naturally. “Machine language”. Then it goes into standby mode.

23. GESTURE SENSING
    It is in standby to be effective, in play forward, backward, turn left, right turn sound effects, do the response action, such as left, right turn, forward, back and so on.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>