AZORES AX1500 WiFi-6 Wireless Router Instruction Manual

June 5, 2024
AZORES

AZORES AX1500 WiFi-6 Wireless Router

Product Hardware Description

Product Backside Description

Reset Button Description

  • Short press (1 second) for reset the router
  • Long press (5 seconds or longer) for reset to factory default settings

LED Description

LED Behavior Scenario
Dark No Power
Steady Red Powering up
Blinking Red No network cable connected
Blinking Green Network connection in progress
Steady Green Function normally and can access the Internet
Blinking Blue WPS or Mesh pairing in progress
Steady Blue Pairing successfully in Master AP Mode

Product Manual

For single router
Connect the provided network cable from the AX-1500 Router to your home Broadband Gateway (i.e. cable/DSL modem, PON gateway). Please refer to SINGLE ROUTER SETUP STEPS for network setup.AZORES AX1500 WiFi-6 Wireless Router-
fig4

For mesh router set
Master AP has the QR code on the bottom,is used as the main router, which is to be connected, via provided network cable, to your home Broadband Gateway (i.e. cable/DSL modem, PON gateway); Slave AP is used for Wi-Fi network expansion. Please refer to ONE ROUTER SETUP STEPS (for Master AP) & MESH SETUP STEPS (for Slave AP) for network setup.

  • When Single Router and Master AP in Mesh Router Set have the same operation steps, they are collectively referred to as Azores Router hereinafter.

ONE ROUTER SETUP STEPS

AZORES AX1500 WiFi-6 Wireless Router-
fig5

  • The Azores Router can be connected according to the diagram above. Note the DSL/PON/Cable Gateway must be connected to the Port 1 of Azores Router. When it is connected to the Internet , the LED light is steady green. If you can, try placing the Azores Router in an open area like on a table or a shelf.
  • Wired devices can be connected directly to ports 2, 3, or 4 for Internet access; wireless devices can use the network name (SSID) & password (see the sticker on the bottom of Azores Router) to connect to the Internet.

MESH SETUP STEPS

AZORES AX1500 WiFi-6 Wireless Router-
fig6

Place the Slave AP at a proper location based on your home layout. After powering on again, Slave AP is all set when the LED is steady green. To optimize wireless performance, place the Slave AP in a location that minimizes the barrier (such as wall, door, and floor) between the Master AP and Slave AP. We recommend one
wall/door/floor between the Master AP and Slave AP. You can connect the Slave AP to your Master AP via network cable (preferred method) or wirelessly.
Note: If you know there is a spot in your home, where the Wi-Fi signal is the weakest. Try to place the Slave AP midway between the Master AP and the weakest spot.
Note: When Master AP and Slave AP pair successfully, the SSID and Password would be the same, that is showing on the bottom of Master AP.

Azores Router APP

  1. Connect your Mobile device to Wi-Fi network according to the Wi-Fi SSID and password sticker on the bottom of the Azores Router.

  2. Download mobile APP software by scanning the QR code below or visiting https://azoresnetworks.com/pages/app-download in the browser.
    Scan QR code to download Azores Router APPAZORES AX1500 WiFi-6 Wireless
Router-fig7

  3. Login with Wi-Fi password on the bottom of Azores Router.

  4. Enter the “My Wi-Fi” menu to modify WiFi configuration or perform other operations.
    Note: If you want to use the mobile device to perform other operations on the router, follow the instructions on the mobile APP.

MORE SETTINGS

Refer to the following steps to change the Internet access method

  1. Wireless access terminals (such as mobile phones, PAD, laptops, etc.) or wired access terminals can open the browser to visit http://192.168.0.1(or http://azoresrouter.com), and configure the router device.AZORES AX1500 WiFi-6 Wireless Router-fig9

  2. Password needs to be set for the first time login, click “Next”. Please remember this login password.AZORES AX1500 WiFi-6 Wireless Router-fig10

  3. Set Internet configuration.

  4. If the home broadband service has been opened and the home router has been deployed, you can connect this Router device to the home router’s LAN Ethernet port (or wall Ethernet port), you can select “DHCP”, then click “Next”.AZORES AX1500 WiFi-6 Wireless Router-fig11

  5. If the home broadband service has been activated, but dial-up is required to activate the Internet, you can select “PPPoE”, fill in the broadband account and password, and click “Next”.

  6. Set Wi-Fi name and password (you can modify the Wi-Fi name).
    The device selects “The password is the same as the login password” by default, clicks “Next”directly, which means that the default wireless password is the same as the login password;

  7. If you do not check “The password is the same as the login password”, you can set a new Wi-Fi password and click “Next”.

  8. If you click “Skip”, the Wi-Fi name and password will still be the information shown on the bottom of the device.

  9. Click “Complete” to complete the configuration.AZORES AX1500 WiFi-6 Wireless Router-fig15

Prompt “Setup Succeed”, and “Confirm” to jump to the login page. After “Confirm”, the wireless terminal can reconnect to the new Wi-Fi name and password.
After completing the settings for the first login, you can use the login password you just set to enter and perform operations such as user password modification, Wi-Fi modification, firmware version check and so on. It is recommended to check the firmware version and update to the latest version after completing the installation.

Refer to the following steps to add a single product customized Mesh

network expansion
For duplexes, villas, and large-area residents, you can purchase multiple Azores Routers of the same model to join the Mesh network to improve WiFi network coverage.

  1. (New item) Visit http://192.168.0.1(or http://azoresrouter.com) and use the login password to log in.
  2. (New item) “Router Mode Settings” select “Slave AP” and click “Save”, the device will restart automatically.AZORES AX1500 WiFi-6 Wireless Router-fig17
  3. Start networking.
  4. If you choose wired networking, connect the new single product network port to the Master AP network port. The wired network is successful when the new single product indicator is steady green;
  5. If you choose wireless networking, place the new item near the Master AP, press both device WPS buttons for 1s, then release. The Master AP indicator will turn on in blue for 1 minute, then restore to the original state. The wireless pairing is successful when new added product indicator is steady green. Wait 2 minutes for information synchronization and the wireless network is successful. You can move the new product to the network expansion location.AZORES AX1500 WiFi-6 Wireless Router-fig18

Refer to the following steps to switch Router to Bridge mode

  1. Visit http://192.168.0.1(or http://azoresrouter.com) and use the login password to log in. 02 Change the “Uplink mode” to “Bridge Mode” on the “WAN Settings” page and click Save.

Frequently Asked Questions

Q1 I replaced my old router with Azores Router. After connecting the network cable from DSL/PON/Cable gateway to the Azores Router, the LED keeps flashing red. What should I do?
Answer: For some cable carriers limit the number of the in-home devices to one. This problem may happen if you replace your old router with Azores Router.In this case, you need to power down the cable gateway, leave it powered down for 15 seconds, and power back it up. Afterward, power down and on the Azores Router. Then you should see the LED turns steady green pretty soon.
Q2 How to reset the device?
Answer: When the Azores Router is powered on, push the “Reset” hole on the bottom of the device with a needle. The LED starts to flash green and holds for 5 more seconds. Release when the LED turns off. The LED will become steady red and will then start to blink green. Wait for about 2 minutes, then the factory default reset is completed.
Q3 Mobile phones and other devices are connected to the router but cannot access the Internet.
Answer: (1) Check whether the Azores Router’s port 1 is connected to your Broadband Gateway. The Azores Router’s network port should be connected to your Broadband gateway (i.e. DSL/Cable modem, PON gateway) with a network cable.
(2) If PPPoE Internet access is needed, you need to check whether the broadband account and password are filled in correctly; otherwise, check whether the Internet status of your Broadband Gateway is normal.
(3) Make sure the broadband service is normal and you have paid the Internet bill.
(4) When all the above are normal, try rebooting the device and then check the network once it powers back on.
Q4 How to manage Azores Router network?
Answer: Connect your device to the Router using a wireless or wired connection. Open an Internet browser and enter http://192.168.0.1(or
http://azoresrouter.com). You can modify WAN configuration, router configuration, single SSID for 2.4 and 5G network, guest Wi-Fi network, and retrieve your wireless network status.
Q5 Azores Router APP cannot control Azores Router.What should I do?
Answer: Please check your phone is connected to WiFi normally, and use the current 5G Wi-Fi password for login.
Q6 If I want to switch the Mesh Router Set to wireless networking after successful wired networking, What should I do?
Answer: Disconnect the wired connection between the Slave AP and the Master AP.It will be OK when the indicator light steady green.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals