Dongguan Solid Model Technology TX01Z TX01Z Remote Control Instruction Manual
- June 5, 2024
- Dongguan Solid Model Technology
Table of Contents
Function
- Push the trigger forward to slow down or break.
- Pull the trigger back to accelerate.
Install the Batteries
- Remove the battery compartment cover.
- Replace the used batteries with new MA size batteries.
Please replace batteries when the power indicator blinks or the buzzer beeps.
Keep the transmitter and receiver 40cm apart when operating.
Throttle trim: If the vehicle inches forward or backward without throttle
input, adjust the trim to set the neutral throttle position.
Steering trim: If the vehicle veers left or right without any steering
input, use the steering trim to adjust the steering servo until the vehicle
tracks straight.
Operating procedure
Always turn the transmitter on before turning on the vehicle. Always
disconnect the vehicle BEFORE turning off the transmitter.
This device complies with part 15 of the FCC Rules. Operation is subject to
the condition that this device does not cause harmful interference (1) this
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation. Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
FCC ID: 2AUBX —TX01Z
CAUTION:
This product is intended for ages 14+ users under 18 years of age and require
parental supervision.
This product is strictly forbidden to be used In water, please do not drive on
water stains.
Introduction
Thank you for purchasing the EAZYRC 1118th Patriot. Engineered to be one of the most realistic, capable, and dependable trucks in its class. the EAZYRC 1/18th series is ready to tackle any terrain right out of the box. This manual is written to assist you in properly operating, maintaining, and repairing the vehicle. As many of the components used are unique to this truck, please retain this manual as a future reference. Composed of precision-made components, the EAZYRC 1/18th Patriot is not a toy, thus it is not suited for children under 14 years of age. Minors should be accompanied by an adult when operating. It is the owner’s responsibility to operate this product in a safe manner.EAZYRC and Its distributors are not responsible in any way for any and all bodily harm and or property damage that may result from the use of this product.
Warnings
- This vehicle is not intended for those under 14 years of age without proper adult supervision. It is not a toy! Failure to operate or maintain this vehicle in a safe manner can result in bodily harm.
- Replace damaged components with original factory parts. Pay special attention to the polarity of all vehicle wiring.
- This product is strictly forbidden to be used in water, please do not drive on water stains.
- Only use approved 2 cell lithium polymer batteries. Do not over-charge or over-discharge the battery as doing so may cause the battery to become a fire hazard. If the battery should become hot during charging, discontinue charging immediately and disconnect the battery from the charger. Never leave the battery unattended while charging. If you are unsure of how to charge this battery, please seek the advice of experienced RC users. Never let children charge the battery without adult supervision.
- The motor will become hot during use. Allow 10-15 minutes between runs for the vehicle to cool down. Doing so will prolong the life of your vehicle.
- Use common sense when selecting the environment to operate your vehicle. Do not operate near power cables, cellular/radio towers, deep water or unstable terrain. The operator is solely responsible for their actions.
- The product is composed of precision electrical components. It is critical to keep the product away from moisture and other contaminants. If exposed to a humid environment, make sure the electronics are fully dried prior to using them again.
- Always check the radio range of the vehicle prior to operation in order to prevent radio loss or interference.
- Operate this product within your ability. If the vehicle is dangerous to retrieve, it’s never worth the risk.
- Always turn on the transmitter before connecting the battery on the model. When turning off the model, always disconnect the battery first, and then turn off the model, always disconnect the battery first, and then turn off the transmitter. If this order is reversed, the model may become uncontrollable and cause serious damage.
- Never allow transmitter batteries to run low as it may cause loss of vehicle control.
- Plastics on the vehicle are susceptible to damage or deformation due to extreme heat and cold climate. Do not store the model near any source of heat such as oven or heater. Store the model indoors, in a climate-controlled, room temperature environment.
- Never shorten the receiver antenna; this may affect the transmitting range of the radio system.
Setting the Gear Mesh
The gear mesh is the clearance between the pinion and spur gears in your
vehicle. If the motor or gearing components are replaced, check that the gears
are not meshing too tightly as this may cause premature wear.|
---|---
Charging the Battery
- Connect the charger to a USB port then connect the battery to the charger.
- When charging, the Green LED is flash, when charged, the Green LED is stable.
- Do not let the battery charge unattended!
- If the battery or charger is hot, disconnect the battery and charger immediately as this may be caused by an internal short-circuit.
Lithium Polymer (LiPo) Battery Warning
- Never charge a lithium polymer battery with a charger designed for Nicd, NIMH, or any other type of battery chemistry. Use ONLY charger designed for LiPo battery.
- Do not leave the LiPo battery unattended during charging.
- Do not overcharge the battery.
- Always charge LiPo batteries on non-flammable, heat-resistant surfaces.
- Always use a LiPo-safe bag or container while charging. Do not allow LiPo cells to overheat at any time. Cells that reach greater than 140 Fahrenheit(60°C) will usually become damaged and will catch fire.
- Do not charge the LiPo pack while it is still in the model. Never charge or store battery packs in a vehicle.
- Do not discharge LiPo; doing so will damage the battery.
- Do not expose LiPo cells to water or moisture at any time.
- Do not store battery near open flame or heater.
- Do not assemble LiPo cells or pre-assembled packs together with other LiPo cells or packs.
- Always store LiPo batteries in a secure location away from children.
- Always remove the LiPo battery if the model is involved in any kind of crash.
- Carefully inspect the battery and connectors for even the smallest damage.
- CAUTION: Cells may become hot after usage. Allow the pack to cool to room temperature prior to recharging.
- Do not allow the electrolyte to get into the eyes or on the skin. Wash affected areas immediately if they come into contact with electrolytes.Do not alter or modify connectors or wires of a LiPo battery pack.
- Always inspect the condition of the battery before charging and operating.
- Do not short circuit the LiPo battery.
- Do not have contact with a leaky/damaged battery directly.
- Do not charge the battery out of recommended temperature range(O°C-45°C).