San Sheng SST03 Remote Controller Instruction Manual

San Sheng SST03 Remote Controller
Instruction Manual

GENERAL INFORMATION

This remote controller is designed to separately control your ceiling fan speed and light brightness.
There are four buttons (HI, MED, LOW, OFF) to control the speed of the fan and off.
The light dimmer button will control the light brightness dimmer and off.
The red indicator on the transmitter will light when one of the five buttons is pressed.

INSTRUCTION OF INSTALLATION AND OPERATION

SETTING THE CODES

This unit has 16 different code combinations. To set the codes, perform the following steps:
A. Setting the codes on the transmitter:
a. Remove the battery cover. Press firmly on the arrow and slide the battery cover off.
b. Slide code switches to your choice of up or down position.
The factory setting is all up.
Do not use this position.
Use a small screwdriver or ballpoint pen to slide firmly up or down (Figure 1).
B. Setting the codes on the receiver:
a. Slide code switches to the same position as set on your transmitter (Figure 2)
b. Replace the battery cover on the transmitter.

INSTALLING RECEIVER IN CEILING FAN

A. Safety precautions:
WARNING: HIGH VOLTAGE! Disconnect power by removing a fuse or switching off the circuit breaker.
Do not use solid-state fans.
The electrical wire must meet all local and national electrical code requirements.
Supply for fan must be 110/120 volt, 60Hz. Maximum fan motor amps: 1.0, Maximum light watts: 180 incandescent or ballast.
Otherwise, power can cause serious injury or death.
B. Installing receiver in fan:
a. Remove power from the circuit.
b. Remove the ceiling fan canopy from the mounting bracket.
c. Disconnect existing wiring between a ceiling fan and Supply in the electrical junction box.
d. Make connections as follows, using the wire nuts supplied:

CAUTION: Ceiling Angle Shall Not Exceed 30 Degrees, For Mounting Controller, Model RC-R26

CONNECT TO
Green fan wire ….Bare supply wire
Red or Black receiver wire(AC IN L) ….Red or Black supply wire
White receiver wire(AC IN N) ….White supply wire
White receiver wire(TO MOTOR N) ….White fan wire
Black receiver wire(TO MOTOR L) ….Black fan wire
Blue receiver wire(FOR LIGHT) ….Blue light wire

If other fans or supply wires are different colors, have this unit installed by a qualified licensed electrician.
e. Push all connected wires up into the junction box.
f. Lay the brown antenna wire on top of the receiver, and put the receiver into the mounting bracket.
g. Reinstall the canopy on the mounting bracket.
h. Restore power.

OPERATING TRANSMITTER:

A. Install a 9-volt battery(not included). (To prevent damage to the transmitter, remove the battery if not used for a long time).
B. Store the transmitter away from excessive heat or humidity.
C. This remote control unit is equipped with 16 code combinations. In order to prevent possible interference from or to other remote units such as garage door openers, car alarms, or security systems. If you find that your fan and light kit go on and off without using your remote control, simply change the code combination in your transmitter and receiver.
D. Operating the buttons on the panel of the transmitter.
HI, key -for fan high speed.
MED key for fan medium speed.
LOW key-for fan low speed.
OFF key-for fan off.
LIGHT/DIMMER key-for light brightness and off.

• The light function is controlled by pressing the LIGHT/DIMMER key down to increase or decrease light.
• Tap the key quickly to turn the light off or on.
  Keep pressing the button in excess of 0.7 seconds and it becomes dimmer, the light varies cyclically in 0.8 seconds.
  The receiver can remember the last status of the light brightness when the light was switched so that it can resume adjusting the light brightness.

FCC Statement:

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
   (1) This device may not cause harmful interference.
   (2) This device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
   NOTE: This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user  is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND LIGHT.

Optional Wall Mounting for Transmitter Holder
Place inaccessible area of your home, and screw the transmitter holder into the wall using the two screws provided, slide the hand unit into holder.

TROUBLESHOOTING GUIDE

1. Fails to operate
   a. Power to receiver?
   b. Receiver wired correctly?
   c. Fan manual speed control in highest position?
   d. Light kit switch turned on?
   e. Good battery in the transmitter?
   f. Code set at exact same positions in both transmitter and receiver?

2. Won’t operate at a distance
   If transmitter operates fan/light kit when up close, but not at 20 feet away.
   Try placing the brown antenna wire higher, up through the ceiling/or outside the junction box.

NOTICE!
Your ceiling fan and light kit assembly must meet the following requirements:

1. Do not use solid-state fans.
2. Electrical rating: 120v 60Hz 3.5A
   MAX. Motor amps: 1.0
   MAX. Light watts: 180-(incandescent, or ballast non-dimmer, or LED)

WARNING
TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH A WALL CONTROL/SWITCH.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>