Verve i2001PB Wireless Charging Power Bank User Manual
- June 5, 2024
- Verve
Table of Contents
User Manual
i2001PB
Wireless Power Bank
i2001PB
Technical Specification
| Model | i2001 PB | Battery Capacity | 3000mAh |
|---|---|---|---|
| USB Type-C Input | 5V/2A | Wireless Charging | 5W |
| USB Output | 5V/2A | Cycle Times | >300 |
| Size | 172(L) 86(W) 11(H) mm |
Product Introduction
-
Product Appearance ① Switch
② USB-C Input/Output ( 5V/2A)
③ USB-A Output (5V/2A)
④ Wireless Charging Output (5W) -
The wireless charger power bank of i2001PB is equipped with USB A to C charging cable and is compatible with most mobile phones and other smart devices.
Operation Guide
-
Power Bank
Connect the USB A or Type-C port of the power bank to the mobile phone with a cable to charge. -
Wireless Charging
Put the phone on the wireless charging pad, press the power button to start charging, or connect with the adapter to start charging. -
Magnetically Attachment
Both the Casetify phone case and wireless charging power bank have a magnet, so they can be easily attached, precisely positioned, and start charging.
Note: When the charger is disconnected (without load) for more than 30 seconds, it will automatically shut down the output circuit and enter the power-saving mode.
Pre-charging
Connect the USB Type-c cable to the device with one end to the power supplier and another end to the charging port.
Notes:
- Supports only Charging of 5V/2A and later.
- The output of a USB of a PC usually is 500mAH which makes the charging slow.
Charging Indicators
-
When charging other devices:
• The power indicators light on accordingly when charging, which indicates the remaining battery of the wireless charger.
• If the indicator light on green flash the charging run out of power. -
Pre-charging the charging power stand
• The power indicators light on indicate the remaining battery of the wireless charger.
• The indicator always be on which means the battery capacity is 100%.
• The wireless charging light on green flashing, which means abnormal charging.
When in Power Bank mode, short press the power button to check the remaining power. The battery status LED will show the remaining power.
| Indicators | 1 light on | 2 light on | 3 light on | 4 light on |
|---|---|---|---|---|
| Battery | <25% | 25-50% | 50-75% | 75-100% |
Troubleshooting
Q: Can’t pre-charge the wireless charging stand.
- Check if it is connected rightly.
- Internal wiring fault. Contact the after-sale service.
Q: No response when charging other devices.
- Low battery. Pre-charge the device.
- Incompatible voltage.
- Connect it in the right way.
- Damaged charging cable or adapter. Contact the after-sale service.
Warning
Announcements
Maintenances
- Please keep the Device dry. Do not let equipment, and battery charger contact water and vapor or use wet hand to operate equipment or charger, Lest cause short-circuits, corrosion caused by equipment failure, and personnel.
- Don’t make equipment, battery and charger strongly impact or vibration. Lest cause equipment, battery and charger fault, fire or explosion.
- Don’t put this equipment, battery, and charger in the too high or too low-temperature region. Otherwise, you may cause equipment, battery, and charger fault, fire, or explosion.
- Don’t hit, throw, acupuncture the Device, and avoid the drop, extrusion, or bending Device.
- Don’t unauthorized equipment and accessories, otherwise, the equipment and accessories will not be in the company’s warranty scope.
Safety Tips
Before using this Power bank, please read this section information, and let your child know this information. For detailed information, please refer to the Safety guidelines and note:
- Do not use a Device in driving, in order to prevent safe driving.
- Please close the Device near the use of high-precision electronic equipment: otherwise, it may lead to electronic equipment being disabled.
- Do not unauthorized to remove Devices and accessories. Only authorized institutions can repair this Device. ‘Please put Device away from magnetic equipment. The radiation of the Device will erase information that is on a magnetic storage device. ‘Please don’t use Device in the high temperature and flammable areas (such as near gas stations). ‘Please don’t put Devices and accessories in this place which children can touch it, please do not let the child use Device in unsupervised. ‘Please abide by the relevant laws and regulations when you use the Device. and respect others’ lawful rights and privacy.
- Please strictly abide by the relevant specifications of this manual when you use a USB cable. Otherwise, it might damage your Device or personal computer. ‘Please don’t use the device in a damp environment such as a bathroom etc. And avoid the Device being soaked or flushed by the liquid.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by the manufacturer could void your authority to operate this
equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirements.