Shenzhen King Serry Electronics SWNK1R01 Wireless Switch User Manual

Shenzhen King Serry Electronics SWNK1R01 Wireless Switch

Product Appearance

Note: The product depicted in this manual may appear slightly different from what you receive in the box

Manufacturer: Shenzhen King-Serry Electronics Co.,Ltd Agent Company: ALTOM INTERNATIONAL INC Address: 9638 RUSH STREET STE D,SOUTH EL MONTE,CA91733 E-Fax: mail: 001-6264444761 bestrose2003@king-serry.com

FCC ID: 2ANPS-SWNK1 R01

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that may cause undesired opera- tion. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in are sidential installation. This equipment generates, uses and can radiate radio  frequency energy and, if not installed and used in accordance with the instruc-tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recep- tion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC sRF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Installation Warnings

1.  Had better program the switch from the receiver for first installation.
2.   Protect the receivers from damage by falling from a height over 1m.
3. Do not touch the output live line with output neutral line after wiring, or the receiver will be a short circuit.
4.  It is not advisable to install a switch on a metal surface or receiver in a metal confined cover, metal will shield wireless signal, thus shortening remote control distance.
5.  Install the receivers where a man cannot reach.

Installation

Reminder : When received the product, the wireless switch and the receiver must be paired up before use- Please refer to the 3rd page : learning code guide.

Learning Code Operation

1. Connect the receiver between the light and the power source.
2. Power on electricity, press and hold the setting button for 2 seconds. When the indicator light flashes, it enters into matching code mode, then loosen your finger.
3.  Press the wireless switch button that you want to pair. Use the wireless switch to control the light on or off, indicating that the learning code is successful.
4. ot recommended that 1 switch controls many receivers.

Adding a switch from paired switch

Press and hold paired switch panel for about 20s till LED indicator on switch blinks rapidly ,then loosen your finger, press the new one ,finally test whether it can turn on/off the lamps.

Delete the switch code that has been paired (Please use cautiously)

Press and hold paired switch panel for about 60s, during which LED indicator on switch changes from: firstly blinks rapidly; secondly blinks 8 times slowly, thirdly blinks 9 times at slower speed, finally blinks once at slowest speed, then loosen your finger, press the switch panel again cannot control the lamps.

Delete the paired wireless receiver code (Please use cautiously)

Press and hold the receiver button for about 10s, loosen you finger when indicator light changes from rapid blinks to slower, press the paired switch panel cannot control the lamps.

Application

The integrated load of the wireless receiver is 1 000W.

Application (Home, hotel, inn or Factory etc.)

How to set Open / Close state of receiver to make wireless switch

compatible with traditional switch

Note: The receiver is default in Close state when leaving the factory.

1.  Power off electricity, install the receiver as the diagram, and distinguish live from neutral lines.
2. Power on electricity, then program receiver with the switch according to the Learning code Operation chapter.

IF the receiver is in Open state

• Turn on the traditional switch to light the lamps, the wireless switch can control the lamps.
• Turn off the traditional switch, wireless switch cannot control the lamps.

Method of set the receiver in Open state:
Press and hold setting button for 16s, loosen your finger when the indicator light is continuously bright. (During the 16s, the indicator light will change from quick flash to slower flash, after that, the indicator light will be off, then will be on.)
IF the receiver is in Close state:
Turn on the traditional switch and press the wireless switch to light the lamps, the wireless switch can control the lamps. Turn off the traditional switch, wireless switch cannot control the lamps.
Method of set the receiver in Close state
Same method of set the receiver in Open state, just press and hold setting button for 16s, loosen your finger when the indicator light is continuously bright.

Replace the battery

1. Remove switch frame and panel with hand or screwdriver.
2. Remove 4 screws with screwdriver, take off the battery cover;
3.  Replace the old battery with the new one, pay attention to the positive and negative poles of the battery;
4. Install the panel and frame again.

Installation

Wireless Switch
The switch can be surface mounted with screws or double-sided stickers. or set it on the table.

1. Install with Double-sided adhesive. (Included) Pick up the area where you re going to place the switch, clean the surface with wet rag, post the adhesive rubber in the back of the switch, then attach the switch to the clean surface.
2.  Install with screws (not included)
   First, take apart the frame and button panel of the switch, Fix the switch base on the wall with two screws, then install the parts together.

Specifications

Parameters of the wireless receiver Specifications

Documents / Resources

| Shenzhen King Serry Electronics SWNK1R01 Wireless Switch [pdf] User Manual
SWNK1R01, 2ANPS-SWNK1R01, 2ANPSSWNK1R01, SWNK1R01 Wireless Switch, SWNK1R01, Wireless Switch
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>