SOUND CRUSH SC-830 Speaker with Fast Wireless Charge User Guide

SOUND CRUSH SC-830 Speaker with Fast Wireless Charger

OVERVIEW

In the box

• 1 x SC-830 speaker,
• 1 x Quick Start Guide
• 1 x TYPE-C charging cable

Safety Precaution

• Read all the instructions carefully before using.
• Check that the voltage marked on the rating label matches your mains voltage.
• The speaker should not be taken apart or modified.

Charge the speaker before use.

1. Connect the speaker with PC/Laptop/Mac, 5V USB adapter or QC 2.0 or QC3.00 power adapter by the TYPE-C cable included. (power adapter NOT included)
2. Red LED turns ON during charging, and turns OFF after fully charged.
3. Unplug the USB cable after fully charged.
4. Red LED twinkles when low power (<21%), with awarning sound.

Bluetooth pairing

1. Turn on the speaker to be ready for pairing. After 1-2seconds you would hear a chime Bluetooth sound.
2. Activate the Bluetooth function on your mobile phone or any Bluetooth device, search the speaker and select the name “SC-830”, and connect the speaker with the device via Bluetooth pairing
3. The Bluetooth sound is chimed once more after being paired, with an LED

Notes

1. Keep the range of 1 meter when pairing. If the pairing was not successful, turn off the speaker and re-pair again.
2. Paired devices will remember each other so there is no need to pair again unless pairing information is deleted.
3. To pair with a new device, follow steps 1-3 above after disconnecting from the existing device.

Compatibility
Bluetooth is compatible with Bluetooth-enabled devices. The Wireless Charge function is compatible with Qi-enabled smartphones and devices.

Power button(power/play/pause function

1. Hold the button. O for approx. 2 seconds to turn on or turn off the device, you would hear a starting chime.
2. When speakers in TWS (True Wireless Stereo) mode, hold the button. on either of the speakers to switch them off.
3. Short click the button. , it would play or pause the music
4. Double click the power button to disconnect the current Bluetooth pairing.

Left arrow

• Short press to decrease volume.
• Long press to go back to the previous song.

Right arrow

• Short press to increase volume.
• Long press to go to next song.

TWS (True Wireless Stereo): to pair one phone with 2 speakers together

1. Make sure you have 2 SC-830 speakers at your hand, turn on both speakers together, then quickly double click the “Power” buttons of both speakers, both speakers will into pairing mode to pair with each other first.
2. Wait for around 5-10 seconds until two speakers “beep” once in sequence, which means both speakers have paired with each other already. The host speaker will show a flash of Blue light whereas the sub-speaker will show solid Blue light.
3. Then, activate the Bluetooth function of your device and pair it with the Bluetooth name “SC-830”. You would enjoy music in True Wireless

Notes:

1. TWS is workable only when you have 2 SC-830 speakers.
2. If you want to disconnect the existing TWS connection, double click the “Power” button of either speaker, the sub-speaker will disconnect, and the host speaker will keep playing music.
3. If you want to establish a TWS connection with 2nd speaker after your device is connected with one speaker already, please long press the “Power” button to disconnect from your existing paired device, then follow above steps 1-3.

How to use the Wireless Charge function

Connect to a 5V Power Adapter (for e.g your phone’s original power adapter) Wireless Charge works only when connected the speaker to a 5V Power Adapter. DO NOT connect to 9V or 12V power adapter!
We recommend using a 5V Qc2.0 or Qc3.0 power adapter to achieve the best stability and fast charging performance. Using a QC1.0 adapter might result in either overheating or a slow charge.

1. QC1.0 power adapter with output 5V/1A is NOT recommended. (charge power is lowered from 10W to 5W if using 5V/1A power adapter)
2. Qc2.0 power adapter with output 5V/2A is recommended.
3. Qc3.0 power adapter with output 5V/3A is recommended.

Place Ql enabled phone or device on the silicon cross.
The phone or device will send an indication image/sound when the charge starts. The speaker turns on the “Green” LED indicator when wireless charging is working.

Notes
Green LED last for 3 seconds and turns off when the wireless charger is in operation. GREEN twinkles when a foreign object is detected.

About working temperature
It is a normal phenomenon of fever during the charging process, please take off the device after fully charged.

Troubleshooting

I feel the charging is slow?
Check if the cable is connected correctly and ensure using QC2.0/Qc3.0 adapter.
Phone or device is not charged?
Ensure the phone is placed correctly on the + in the middle of top surface. Power ON/OFF your phone and retry Make sure your phone or device is wireless charge enabled.
Device or Wireless Charger is very warm?
Ensure you use the correct adapter. Do not cover both phone and wireless charger during charging.

Specification

• Speaker output: 5W
• Wireless charge: 10W fast charge
• Bluetooth range: 10 meters
• Driver: 2.0-inch full range
• Battery: 3.7V 1800mAh rechargeable
• Input: 5V DC
• Material: plastic, silicone.

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>