beurer MM 50 4-Ply Medical Face Masks Instruction Manual

: June 5, 2024
: Beurer

Table of Contents

beurer MM 50 4-Ply Medical Face MasksIncluded in delivery
Intended use
WARNING
IMPORTANT
Use Putting on a mask
Taking off a mask
Storage
Technical data
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

beurer MM 50 4-Ply Medical Face MasksIncluded in delivery

Check that the exterior of the cardboard delivery packaging is intact and make sure that all contents are present. Before use, ensure that there is no visible damage to the mask and that all packaging material has been removed. If you have any doubts, do not use it and contact your retailer or the specified Customer Services address. Signs and symbols The following symbols appear in the instructions for use and on the packaging:

| WARNING

Warning notice indicating a risk of injury or damage to health

---|---
| CAUTION

Safety note indicating possible damage to the device/accessory

| Manufacturer
| Date of manufacture

|

Dispose of packaging in an environmentally friendly manner

| CE labeling

CE mark with Notified Body identification number. This pro- duct satisfies the requirements of the applicable European and national directives. The product complies with the PPE regulation (EU) 2016/425 (reference: OJ L 81, 31/03/2016). As well as EN149:2001 + A1:2009 (refer-

rence: OJ C 113, 27/03/2018)

---|---
| Humidity range
| Temperature range
| Not suitable for reuse
| Protect from sunlight
| Batch designation
| Protect from moisture
| Use by
| Not sterile

Intended use

The Beurer MM50 FFP2 mask (particle-filtering half-mask) is an item of personal protective equipment (PPE) for use in the context of occupational safety and is intended to protect the wearer of the FFP2 mask from potentially damaging particles and droplets as well as both liquid and solid aerosols. The FFP2 mask filters both the air you inhale and the air you exhale. Alt-hough the mask is primarily designed for self-protection, it not only protects you as the wearer but also those around you.
Warnings and safety notes
Read these instructions for use carefully! Failure to observe the information below may result in personal injury and reduce the effectiveness of the respiratory protection mask. Retain these instructions for use and make them accessible to other users. Make sure you include these instructions for use when handing over the product to third parties.

WARNING

Keep packaging material away from children There is a risk of suffocation.
Children must not play with the FFP2 mask.
Before each use, check the FFP2 mask for external damage (e.g. tears or holes). If the FFP2 mask is damaged, DO NOT use the FFP2 mask.
Materials in the FFP2 mask that come into contact with the skin may cause allergic reactions in people with sensitive skin.
Safe handling is necessary when using FFP2 masks. Non-compliance increases the risk of infection for the mask wearer.
If the FFP2 mask is saturated with moisture or you suspect contamination, replace the FFP2 mask immediately.
Do NOT use or pass on FFP2 masks if you have been in the vicinity of infectious individuals with significant exposure to aerosols.
Do not wear the FFP2 mask over your mouth only. Make sure that the FFP2 mask covers both mouth and nose correctly (see the section titled Use).
When wearing the FFP2 mask, ensure that the metal clip is always at the top. Do not put the FFP2 mask on upside down, as this prevents the protective seal from being effective.
Do not wear the FFP2 mask around the neck as this may contaminate the chin and neck area.
Sealing of the FFP2 mask cannot be guaranteed for persons with beards or scarred skin in the area of the foam strip.
The outside of the used FFP2 mask may potentially become contaminated. Avoid contaminating the wearer via the outside of the mask, especially on the face.
The FFP2 mask helps to protect you against specific particle contamination but does not eliminate the risk of contagion or infection.
Replace the FFP2 mask if it is damaged or deformed and/or does not fit tightly on the face
Do NOT use the FFP2 mask if the ambient air contains less than 19.5% oxygen and/or if you can smell or taste pollutants
Do NOT use the FFP2 mask to protect against gases or vapors.
Do NOT use the FFP2 mask if the pollutants or their concentrations are unknown to you or are life-threatening and hazardous to health.
Do NOT use the FFP2 mask when sandblasting, spraying paint, or treating asbestos and/or in an explosive atmosphere

IMPORTANT

Make sure that the FFP2 mask does not come into contact with grease, oils, or alcohol (e.g. cleaning products or face lotions).
To increase safety, regularly conduct training in the handling of personal protective equip-ment (PPE).
Cleaning, maintenance, and disinfection of the mask are not intended, as it is designated for single use.
Do not modify the FFP2 mask and do not add or omit any parts
A mask marked “NR” must not be used for more than one shift.
In the event of aerosol exposure, minimum FFP2 masks are required for the individual providing treatment.
Fit the nose clips of the FFP2 mask to your nose. When doing so, ensure that the nose clip of the FFP2 mask sits firmly on the nose in order to guarantee that the mask is sealed and so that no exhaled air can escape upwards.
To ensure a tight fit for the FFP2 mask, always unfold the FFP2 mask fully.
Make sure that the securing straps of the FFP2 mask are correctly positioned, as otherwise, it is not possible to achieve a seal.

Use Putting on a mask

WARNING
FFP2 masks are individually packaged. Take out only one FFP2 mask from the packaging. Leave the remaining unused FFP2 masks packaged.

Fully unfold the FFP2 mask. Do not touch the inside of the FFP2 mask while doing so.
Use one hand to place the FFP2 mask over your face in such a way that your mouth and nose are covered. Using the other hand, pull the securing straps over your ears.
Make sure that both securing straps are flat and not twisted.
Make sure the FFP2 mask fits snugly and comfortably on your face and cannot slip. Using your index finger, push the outer metal clip of the FFP2 mask firmly onto the bridge of your nose. Using your other hand, adjust the metal clip to your nose shape so that the FFP2 mask fits as tightly as possible and there is as little space as possible above the bridge of the nose. is created.
To check this, hold both hands in front of the FFP2 mask and breathe out hard. If air escapes above the bridge of the nose, press the metal clip more firmly onto the bridge of your nose. If air escapes from the side of the FFP2 mask, reposition the securing straps. Repeat the breathing-out exercise until the FFP2 mask fits tightly.

Taking off a mask

Pull the straps off over your ears. Ensure that the outside of the FFP2 mask does not come into contact with your face or eyes. Pull the FFP2 mask in a forward direction to remove it.
After use, dispose of the mask in accordance with applicable regulations, without touching the outside of the mask
Wash your hands thoroughly after using the mask

Storage

When not in use, store the FFP2 mask in its original packaging outside contaminated areas.
Keep the FFP2 mask in its original packaging (carton or film packaging) during transport.
Store the FFP2 mask somewhere dry and protected from sunlight.
Comply with the specified storage and transport conditions.

Technical data

Type SAAFFP2
Model MM 50
Protection level FFP 2 NR
Description of the mask Explanation: Particulate-filtering half-mask FFP = filtering facepiece Protection class 2 = filter performance ≥ 94%NR: non-reusable Product classification: EN 149:2001+A1:2009
Durability Intended for single-use; when stored in a closed bag: 3 years.
Storage and transport stipulation -30°C ~ 40°C, 0-80% RH

Notified body:
Universal Certification and Surveillance Service Trade Ltd. Co. Necip Fazıl Bulvarı Keyap Sitesi E2 Blok No: 44/84 Yukarı Dudullu Ümraniye-Istanbul
Turkey
Number: 2163
EU declaration of conformity:
https://www.beurer.com/web/we-landingpa-ges/de/cedeclarationofconformity.php
Service
Customer Service Address
Please contact our customer service if you have any questions. Please find the service address in the attached address insert