Shangraoshi Fenghe Dianzishangwu Youxiangongsi 2A4X618KEY RGBW LED Wall Washer Lamp with 18-Key Remote Installation Guide
- June 5, 2024
- Shangraoshi Fenghe Dianzishangwu Youxiangongsi
Table of Contents
RGBW LED Wall Washer Lamp with 18-key Remote
IMPORTANT: To ensure safety, make sure the power supply is turned OFF before installation. Perform installation in accordance with the National Electric Code(NEC) and local code specifications.
INSTALLATION GUIDE(Wall Mounting)
(Versatile Mounting Options With 180-degree Bracket), Wall mount, Pedestal mount, and ceiling mount)
-
Drill The Holes: Fasten the screws on both sides with a hex key. Mark the positions of the holes with the wash light bracket, then drill the fixing holes.
-
Drive-In: The Bolts fasten the screw clockwise with the hardware wrench. Drive in the bolts to the pre-drilled holes with the thread outside.
-
Place The Fixture: Make the bracket face tightly against the wall through the thread.
-
Rotate And Fasten: Rotate the light to the desired angle and fasten the screws.
Specifications
- Wattage: 108W(36pcs full spectrum 3W LEDs)
- Voltage: AC90-277V 50/60Hz;
- Waterproof rating: IP65;
- Working temp: -25°C- +45°C;
- Material: Die-casted aluminum+ Strong Glass+stainless steel material;
- CRI>80;
- Linear Strip Length: 3.2ft/ 40inches;
- Lighting Beam Angle: 10X60°;
- Working Time: 50,000 Hrs+;
- Lighting Color: red, green, blue, white (NOT PURE) ; yellow, purple, cyan, pink;
- Plug Cord Length: 59.06 in/1.5m US 3-Plug and male and female extension cord;
- Remote Distance: Up to 98ft;
- Bracket Degree: 180-degree.
Product Size (mm)
18-KEY RF REMOTE CONTROLLER(The Battery: 12V 23A)
New Upgraded Brightness Mode: Adjustable 5-level brightness (100%-25%), Not only adjust color brightness but also can adjust lighting mode brightness.
New Upgraded Memory Function: Will stay at your lasting setting while turning on again. Also can remember the dim level(Limited to turn on/off with remote, if power off more 5 minutes, turn on the light again, the light will keep 100% brightness).
10 Lighting Mode: M①: 7-Color Fade(no pink); M②:7-Color Slow Flash(no
pink); M③:7-Color Breathe(no pink); M④:R G B W Fade; M⑤: R G B W Jump; M⑥:R G
B Fade; M⑦:8-color Jump;
M⑧:Red Fade+Jump; M⑨: Green Fade+Jump; M⑩:Blue Fade+Jump.
Auto Lighting Mode: 10 Lighting mode automatic cycle.
Timer Mode: Pre-setting the 2 hours turn on or make it turn off 4 hours or 6 hours automatically.
► Note: Press the time switch button, the green light will flash 3 times, which means the timer function is turned on, then set the corresponding time to turn on or off, if the green light flashes 3 times again, which means the time setting successfully.
►What You Get
- 1* 3.2ft Wall Washer LED Light Bar;
- 1* User Guide;
- 1* 1.5m 3-prong plug extension cord;
- 1*Installation Tool Kit;
- 1* 18-key RF Remote Controller;
►Gift Installation Tool Kit
- 1* 8mm Open-Ended Wrench;
- 1*16mm Open-Ended Wrench;
- 12.518*53 mm Allen Wrench;
- 1421*57 mm Allen Wrench;
- 1* Waterproof 3 Core Male Female Plug.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.