Measy Technology FHD676 Wireless HDMI Extender User Manual

Wireless HDMI Extender
1080P, 5G Frequency

User Manual

Panel Descrption

INSTALATION INSTRUCTIONS

STARING UP GUIDELINE

WIRLESS IR REMOTE CONTROL

BACKGROUND

Boot setting 1
Place the transmitter and the receiver together. After the product is powered on, the transmission indicator is always on

****  The transmission indicator lighting is in normal transmission

Connecting WiFi 2
Use the mobile phone to search for the name: ” HDMI-Extender ” in the WiFi setting, the default password is 12345678.

If you forgot your password, you can press and hold on to the RESET button for seconds to restore the factory default settings when the transmission and receiver power are on.

BACKGROUND SETTING

FAQ

Frequently Asked Questions

Q: Can I use multiple sets of products in the same environment?
Log in to the WEB background and modify the SSID name of each product without repeating it. You can use multiple sets of products in the same environment.
Q: What is the maximum transmission distance?
Wireless Transmit 150m 492ft, Can through Wall in an open field, this wireless HD sender HDMI wireless signal can up to 150m 492ft(line of sight), if through 1 wall the signal can transmit 10-20m/32ft-65ft
Q: What is the meaning of the LED light?

1. Power indicator LED: the power indicator LED is continuous lighting after power on.
2. Transmission indicator: When the receiver connects to the transmitter successfully, the transmission indicator LED is lit.

Q: There is a picture, but no audio

1. Please make sure the audio format of the HDMI signal source is LPCM2.0.
2. This HDMI support audio format includes: LPCM2.0/48KHZ/16Bit
3. If the HDMI signal source is 5.0/dolby or another audio format, there will be no sound.

Q: There is no picture and audio

1. Check whether the receiver power supply is normal
2. Confirm that the input and output in Transmitter and receiver are right connected
3. Check if the HDMI cable is damaged

Q: TV only Show “Connecting…”

1. Check the transmitter power supply is normal
2. Check whether the WEB settings are correct
3. Press the product reset button or power off to restart the product, will take 1 min to reconnect
4. Same frequency causes interference, adjust the transmission frequency or frequency channel, avoid the interference frequency

Q: Receiver displays No signal

1. Check the signal source HDMI output signal is normal
2. Confirm the output resolution of the signal source is within the support range
3. Make sure the source is connected to the transmitter’s HDMI input

Q: The image interferes

1. Inadequate signal transmission, adjust the angle of the antenna or shorten the distance of devices
   Frequently Asked Questions 2

2. Adjust the placement and height of the transmitter and receiver to enhance wireless signal transmission.

3. Same frequency causes interference, adjust the wireless frequency or frequency channel to avoid the interference frequency(refer to BACKGROUND SETTING)

Q: IR wireless return function is insensitive

1. Infrared remote has different frequencies, our product can be matched by selecting the the38KHz frequency to control, not supporting 47KHz and 56KHz
2. Adjust the placement and height of the transmitter and receiver to enhance wireless signal transmission.
3. Transmitters have an IR signal transmission function, when the transmitter is placed above the”top box, check whether the transmitter bulging”set-top box”1-2cm.
4. Transmitters have an IR signal transmission function when using the external IR extension cable. Try to keep the transmitter away from the”set-top box” and avoid sending infrared signals at the same time to cause remote control conflicts

Q: Unable to log in to the web settings interface

1. Verify the transmitter and receiver are powered on and connected successfully
2. Check whether the IP address configured on the device is set to the static IP type
3. Check whether the IP address configured on the device is set to 192.168.1. XXX
4. Try to replace the browser with a different browser and log in to the Wed Settings

CONTENTS

SPECIFICATION

FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Statement

To maintain compliance with FCC’s RF exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm from the radiator of your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>