GAGGENAU DF481100 Dishwasher User Guide
- June 9, 2024
- Gaggenau
Table of Contents
- GAGGENAU DF481100 Dishwasher User Guide
- Overview of water hardness settings
- Hardness mmol/l Setting range value
- Adding special salt
- Setting the water softening system
- Adding special salt
- Adding rinse aid
- Adding detergent
- How to use your appliance
- Cleaning filters
- Cleaning spray arms
- Clean wastewater pump
- Troubleshooting
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
GAGGENAU DF481100 Dishwasher User Guide
Overview of water hardness settings
You can find an overview of the water hardness values that can be selected
here.
A table of country-specific units can be found in the instruction manua
Medium 1.5 – 1.8 11 – 12 __
Medium 1.9 – 2.1 13 – 15 __
Medium 2.2 – 2.9 16 – 20 __
Hard 3.0 – 3.7 21 – 26 __
Hard 3.8 – 5.4 27 – 38 __
Hard 5.5 – 8.9 39 – 62
Hardness mmol/l Setting range value
Soft 0 – 1.1 0 – 8 __
Soft 1.2 – 1.4 9 – 10 __
Adding special salt
Setting the water softening system
- Press .
- To open the basic settings, press for approx. 3 seconds.
- Press repeatedly until the display shows “Water hardness”.
- Press or repeatedly until the right water hardness has been set.
- To save the settings, press for approx. 3 seconds
Adding special salt
-
To avoid damage to the appliance, only add special salt to the dispenser for special salt just before the programme starts.
Unscrew the lid of the dispenser for special salt and remove. -
On initial start-up: Fill the dispenser right up with water.
-
Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent.
Adding rinse aid
-
Press the catch on the lid of the dispenser for rinse aid and lift .
-
Close the lid of the dispenser for rinse aid. a The lid clicks into positio
Adding detergent
How to use your appliance
-
Load the tableware. Only clean tableware that is suitable for dishwashers. Remove large remnants of food from
the tableware. Check that the spray arms can ro -
tate freely. Add detergent.
-
Switch on the applianc
-
Select the programme.
-
Start the programme .
-
Remove the tableware at the end of the programme.
-
To cancel the programme, press for approx. 4 seconds. The programme is cancelled and ends after approx. 1 minute.
Cleaning filters
-
After each wash check the filters for residue.
-
Turn the coarse filter anticlockwise and remove the filter system .
-
Press the locking catches together and lift the coarse filter out
. -
Clean the filter elements under running water.
-
Re-assemble the filter system.
-
Insert the filter system into the appliance and turn the coarse filter clockwise. Make sure that the arrow markings match up
Cleaning spray arms
Unscrew the upper spray arm and pull down to remove .
Pull up the lower spray arm to remove
3. Check the outlet nozzles on the spray arms for blockages under running
water and remove any foreign bodies.
4. Insert the lower spray arm.
a The spray arm clicks into position.
5. Insert the upper spray arm and screw it firmly in plac
Clean wastewater pump
-
Disconnect the appliance from the power supply.
-
Remove the filter system.
-
Scoop out any water.
-
Prise off the pump cover using a spoon and grip it by the crosspiece
-
Lift the pump cover inwards at an angle and remove.
-
Remove any remnants of food and foreign bodies in the area of the impeller.
-
Insert the pump cover and press down . a The pump cover clicks into position
Troubleshooting
Fault Cause and troubleshooting
E:3200 or indicator for water supply lights up.
Supply hose is kinked.
▶ Install the supply hose without kinks.
Water tap is turned off.
▶ Turn on the water tap.
Water tap is jammed or furred up.
▶ Turn on the water tap.
The flow rate must be at least 10 l/min when the water supply is open.
The filters in the water connection of the supply or AquaStop hose are
blocked.
- Switch off the appliance.
- Pull out the mains plug.
- Turn off the water tap.
- Unscrew the water connection.
- Remove the filter from the supply hose
- Clean the filter.
- Re-insert the filter in the supply hose.
- Screw the water connection back on.
- Check the water connection for leaks.
- Restore the power supply.
- Switch the appliance on
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>