Jiangmen City Heliansheng Electronic S7 Motorcycle Handheld Bluetooth Speaker User Manual

jiangmen City Heliansheng Electronic S7 Motorcycle Handheld Bluetooth

Speaker

Features

• 5.0 Bluetooth Audio
• 3.0 USB
• FM radio
• Aluminum alloy shell

Packaging Content

Please check whether the accessories are complete after receiving the goods

• Main Speaker x1 and Slave Speaker x1
• Antenna x1
• Power Cord x1
• Hex Screw DriVer x1
• Screw x2
• Non-slip Meson x2
• Upper and Lower Bracket x4
• Rubber Pad x6
• Nylon ties x10
• User Manual x1

Wiring

Step 1: The red end of the power cord is connected to the positive pole of the battery, the black end of the power cord is connected to the negative pole of the battery, and then connect the power cord to the host.(Fig ① )

Step 2: Plug the speaker connector of the main speaker to the slave speaker. (Fig Note: Please remember the two arrows on each connector should be on one line.

Step 3: Connect the external antenna to the main speaker antenna connector. (Fig ③)

Note: To ensure safe wiring, the power cord should not be installed around any moving parts and away from spark plugs and high-temperature devices, so as not to damage the sound system.

Operating Instructions

PWR knob

• Press the knob for a short time to turn on, and press and hold for about 2 seconds to turn it off.
• In the radio mode, press the knob shortly to mute, and then press the knob shortly to release the mute.
• In Bluetooth or USB mode, short press the knob to pause, then press release to pause playback.
• Rotate clockwise to turn up the volume, and rotate counterclockwise to turn down the volume. When the volume is turned to the maximum, there will be a prompt tone.

MODE knob

• Short press the knob to switch radio/Bluetooth/USB mode
• In the radio mode, clockwise rotation is to search for a station to the high end, and counterclockwise rotation is to search for a station to the low end.
• In Bluetooth or USB mode, clockwise rotation is downward music selection, and counterclockwise rotation is upward music selection.

USB Music Mode

After inserting the USB, MP3/FLAC/AWV audio songs will be played automatically.
Note: USB mode can only be switched when an external USB source is connected.

Bluetooth Connection

To pair and connect your Bluetooth device to the S7, enter the MOD knob until you hear the voice prompt “Bluetooth mode”, which means that it has turned to Bluetooth mode. At this time, you can use your Bluetooth device to connect with Bluetooth. After the connection is successful, you will hear the prompt tone
of “Ding Dong”.

Installation Instructions

Mount each speaker with its clamp to the handlebar of the motorcycle
Note Different size handlebar please insert different slot of the bracket as below

Technical Parameters

Radio frequency range——————————————-87.5-108MHz

Frequency response———————————————-70Hz~15KHz

S/N—————————————————————-> 75dB

THD—————————————————————< 1%

Output power:—————————————————- 35W

Bluetooth connection distance———————————-> 15m

Operating voltage————————————————10～16V

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>